1 December 2023 in Journal of Polytechnic
The aim of this study was to determine some physical and mechanical properties of spruce (Picea orientalis) wood, which was impregnated with aqueous solutions of valonia (valex) (the extract of Quercus ithaburensis), pine bark powder (pinex) (Pinus brutia Ten.) and gallnut powder (galex) (Quercus infectoria Oliver) as a pre-treatment and then heat treated. Test specimens were prepared from sapwood of spruce wood and impregnated with 10% tannin solutions before heat treatment base on ASTM D 1413-76. After pre-impregnation processs, specimens subjected to heat treatment at 150 °C, 175 °C and 200 °C for 2 h. The effect of impregnation process and heat treatment temperature on the air-dried density, compressive strength paralell to the grain (CS), bending strength (MOR) and modulus of elasticity in bending (MOE) were analyzed. As results, impregnation solutions showed positive effects on mechanical strength in unheat-treated samples and determined that mecnaical strength loses due to heat treatment slightly limited at low temperatures. However, strength loses increased with increasing temperature. The highest strength loses were also determined in impregnated samples with galex extract and heat-treated samples at 200 °C.
19 March 2022 in Drvna industrija
In this study, the effects were examined of wood species, processing types and processing time on diagonal tension performance of woodworking corner joint with double tenon and mortise. Test samples were prepared by using Scots pine (Pinus sylvestris Lipsky), sessile oak (Quercus petreae Lipsky) and black locust (Robinia pseudoacacia L.). Poly vinyl acetate (PVAc) adhesive was used to join the tenon and mortise corner joints. The samples were impregnated by using the method of immersion for 20 and 40 min with a mixture of wax / linseed oil (3 % paraffin, 10 % linseed oil, 87 % white spirit) and Imersol-Aqua. The test of diagonal compression was used to test 120 samples. In this study, the minimum strength decrease of around 68 % was obtained for Scots pine impregnated with Imersol-Aqua for 40 min and the highest strength increase of around 10 % was obtained for sessile oak samples impregnated with Imersol-Aqua for 40 min. The highest diagonal tension performance of 879.734 N·m was obtained for oak samples impregnated with Imersol-Aqua for 40 min., the lowest diagonal tension performance of 189.111 N·m was obtained for Scots pine samples impregnated with Imersol-Aqua for 40 min.
18 May 2023 in BioResources
9 September 2025 in Drewno. Prace Naukowe, Doniesienia, Komunikaty = Wood. Research Papers, Reports, Announcements
This study aims to evaluate the adhesion resistance of water-based single-component varnish layers to wood surfaces by incorporating sodium borate in varying proportions. The research was conducted using specimens obtained from wood materials of Scots pine (Pinus sylvestris L.), Turkish fir (Abies bornmülleriana Mattf.), Sessile oak (Quercus petraea L.), and Oriental beech (Fagus orientalis L.). These specimens were impregnated with sodium borate solution at concentrations of 1.5% and 2.5%. After the impregnation process, water-based varnish formulations containing different proportions of sodium borate (1.5% and 2.5%) were prepared. Once the varnish layers were fully dry, an adhesion test was conducted according to ASTM-D 4541-02 standards. As a general conclusion, it was found that the modified varnish and impregnation processes resulted in the highest efficiency with beech and oak wood materials, while the impact of the sodium borate was more limited on scots pine and fir wood materials.
1 February 2021 in BioResources
Glue shear strength and wood preservatives play an important role in the longevity of engineered wood products. The effects of factors such as UV rays, humidity, and temperature on wooden materials are known. However, it is not known what effects sub-zero temperatures have on wood material and how wood preservatives play a role. This study determined the effects of synthetic-based varnish and impregnation on shear strength in cold climatic conditions. Variables including glue type, ambient temperature, tree type, and process type were investigated. Wood laminate test samples were produced for this purpose, and water repellent impregnation material and synthetic-based varnish were used as wood preservatives. Experimental samples were kept in a cold air cabinet at (-15 °C) and (-30 °C) temperature for 90 days. Samples kept in different temperature conditions were subjected to a pull experiment in a parallel (//) direction to the fibers under static load. As the ambient temperature decreased, the shear strength decreased (-15 °C: 8,960 N/mm2 ,-30 °C: 8,025 N/mm2 ) . When the performance of wood preservation elements were examined, it was determined that the varnish process (8,875 N/mm2) and the impregnation process (8,691 N/mm2) were not statistically significant, at 12% and 10%, respectively.