20 June 2025 in Engineering Technologies and Systems
Introduction. Low level of technical support for breeding works results in a high share of manual labor in the industry, violation of agrotechnical requirements, increased losses of expensive seeds, high production costs that is a constraint of developing domestic breeding and expanded reproduction of seeds. Machine harvesting of cultivated seeds is a most important operation in breeding and seed production. During this operation, a significant amount of energy is expended and a large volume of exhaust gases is released that makes important conducting the studies on improving plot combine harvesters in the direction of improving the quality of harvesting work and energy saving indicators, and of reducing the negative impact on the environment.Aim of the Study. The study is aimed at improving the quality of technological operations, energy efficiency and ecological compatibility of plot combine harvesters by using an automated electric drive and a hybrid power-generating plant with electric energy storage units.Materials and Methods. The object of the study was the technological process of the plot grain combine harvester. The basis of the study was scientific publications on the technologies of machine harvesting of selected grain crops and information materials of the manufacturers of plot combine harvesters. In the process of the study, there were used such methods as system analysis, structural and functional analysis, and synthesis.Results. There was carried out the analysis of machine harvesting technologies, technical characteristics and operating modes of modern plot grain combine harvesters. Based in its results, there were identified the patterns of energy consumption during the performance of the plot combine harvester. There was carried out structural analysis of the plot grain combine harvester and a functional diagram was constructed. In order to increase its energy efficiency, quality of work and reduce the negative environmental impact, there was proposed the use of removable energy modules with an electric drive and of an electric drive for the combine units. There have been developed the recommendations for using the electric drive of the working bodies, options for using various power plants including removable energy modules, and a functional diagram of a plot grain combine harvester with an automated electric drive of the main units powered by a removable energy module.Discussion and Conclusion. The studies contribute to solving the problems of increasing energy and economic efficiency, reducing the negative environmental impact when performing machine harvesting operations in breeding through the use of an integrated power plant. The use of additional electric drive and electric energy buffer storages according to a so-called hybrid scheme, allows reducing the impact of unbalanced loads on the internal-combustion engine performance. These unbalanced loads are caused by the peculiarities of the technological process of harvesting plots, where the loading cycles with pronounced modes of maximum power without going through the transitional modes are replaced by periods of insignificant power consumption. There has been defined a set of tasks for further studying. These tasks include determining the optimal parameters of the removable energy module and electric drive of the main units of the plot combine harvester using the method of mathematical simulation of their energy consumption in various operating modes.
28 June 2023 in Agricultural science Euro-North-East
The need to use such propulsion devices in mobile agricultural power units is substantiated. The relevance of this development based on global trends is shown. The purpose of the research is to develop the design, to evaluate strain-stress state and functional characteristics of undercarriages of agricultural tractors with replaceable half-tracks. An experimental design of the replaceable tracked undercarriage was developed and manufactured, modeling of loading modes was performed, calculations were carried out by the finite element method of the stress-strain state of structural elements according to 6 load schemes – tractor parking on a flat horizontal surface; movement with maximum traction force; parking across a 30° slope for the upper track; parking across a 30° slope for the lower caterpillar; driving into an obstacle with a deviation of 15°; driving over obstacles based on the central rollers. It was determined that the selected structural material, by the above mentioned loading modes ensure the operability of replaceable tracked undercarriage. Calculations were carried out to check the adequacy of the developed mathematical model using field tests in testing ground of FSAC VIM. It was determined that the maximum stress-strain state of the frame structure of a replaceable tracked undercarriage for all types of loading did not exceed 100 MPa. This provides a two-fold margin of safety in terms of fluidity of the structure, taking into account the characteristics of the selected material. In the maximum loaded state - parking across a slope of 30° - the highest stress on the upper track is 161 MPa, which corresponds to a safety margin of 1.45. The deformation of the bearing assembly was no more than 4 mm, which is allowed by the design of the drive assembly and the caterpillar.
7 December 2025 in Tractors and Agricultural Machinery
BACKGROUND: The paper discusses the process of modeling the motion of grain and foreign impurities carried by the air flow in the grain transportation and cleaning system of a breeding combine harvester, which is necessary to improve the quality of grain cleaning and to optimize the development and adjustment of such cleaning systems. AIM: Building a digital twin of the transportation and cleaning system with the ability to simulate the motion of particles in the air flow. METHODS: A digital model of the grain transportation and cleaning system was used as the object of study. Modeling of the process and study of particle movement in an air flow using the discrete element method was carried out at the Don Engineering Center as part of the SRW of the Federal Scientific Agroengineering Center VIM. The particle parameters were selected based on measurements of real impurities in the grain heap of the Anfisa wheat variety. RESULTS: The composition of the grain heap was clarified, the geometric dimensions and masses of typical particles — grains, chaff, awns, etc. — were measured, their digital models were created. A digital model of the grain transportation and cleaning system of a breeding combine harvester was created, with the help of which a study of the motion of particles in the air flow was carried out, in particular - their paths, motion velocities. The grain heap motion route was modeled from the time it enters the grain intake from the sieves by the time it passes the cyclone filter of the cleaning system. Some air flow parameters were measured on a physical sample of the pneumatic grain transportation and cleaning system installed on a breeding combine harvester. CONCLUSION: To improve the quality of grain cleaning in a selective combine harvester and optimize the development and configuration of such cleaning systems, the possibility of conducting research in a digital environment for a design requiring optimization of many parameters is considered, using the example of a digital twin of a grain transportation and cleaning system with the ability to simulate particle motion in an air stream.
1 August 2026 in Emerging Science Journal
This study presents an energy-based approach to compensatory control of the cutting frequency of a reciprocating cutter bar of a grain combines harvester under variable stalk density and limited drive power. The methodology combines analytical modelling, laboratory experiments, and simulation. First, the inertial characteristics of the cutting unit are analyzed to determine conditions for stable operation at a given target drive frequency. Then the cutting force for a single wheat stem is obtained experimentally on a laboratory rig based on a breeding combine cutter bar, and the cutting energy per stem is estimated from a series of repeated sheaf-cutting tests. These data are used to parameterize a mathematical model that links stalk density, total cutting resistance, drive load, and the resulting deviation of the actual cutting frequency from the target value. On this basis, a simulation model of standing-grain cutting is constructed in the form of a digital twin of the cutting device, enabling evaluation of the influence of spatially varying stalk density, stem orientation, and re-cutting of previously severed stems on the drive load. The results show that realistic fluctuations in stalk density can produce resistance peaks that exceed the available drive capacity and significantly reduce actual cutting frequency. The developed model provides a quantitative basis for designing compensatory control strategies that adapt the operating mode of the cutter bar to the predicted load, thereby maintaining the target cutting frequency, reducing overloads, and improving the quality and energy efficiency of grain harvesting.
28 August 2025 in Agricultural science Euro-North-East
The aim of the study was to determine and calculate the required operating range of the suspension of the platform wheel modules for breeding and seed production by studying its operating characteristics considering the aggregated machines and operating conditions. Based on the developed mathematical model of the platform suspension for breeding and seed production and its design characteristics, a simulation model of the platform suspension operation under the operating conditions of a given technological process was compiled. The simulation model contains the parameters of road surface unevenness, as well as the specified speed and longitudinal acceleration of the platform. The objects of research were the elastic-damping characteristics of the suspension elements of the platform for breeding and seed production. Based on the results of the research, the ranges of force adjustment, spring stiffness and shock absorber damping coefficient were determined. Thus, the range of adjustment of the force on the elastic element of each technological module of the chassis should be 5886–25715 N, the range of adjustment of the spring stiffness 34220–136883 N/m, the range of change of the damping coefficient of the shock absorber 9043–18086. Based on the obtained values of the suspension operating ranges, layout solutions for the design of the platform suspension for breeding and seed production work were given: a change in the stiffness parameters can be ensured by using two- or multi-stage stiffness change systems, and a change in the damping coefficient - by means of a controlled regulator of the hydraulic fluid flow.