Nicoleta Nicoara

Nicoleta Nicoara

Auto-generated profile, based on publicly available information

Nicoleta Nicoara

INL - International Iberian Nanotechnology Laboratory

Research Focus & Metrics

Academic Career Length

25Years (2002-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
30 January 2020 in Advanced Energy Materials
Verified
Journal Article
Open access
PDF file
SSSusanne Siebentritt
Susanne Siebentritt
EAEnrico Avancini
Enrico Avancini
MBMarcus Bär
Marcus Bär
JBJakob Bombsch
Jakob Bombsch
EBEmilie Bourgeois
Emilie Bourgeois
MWMax Hilaire Wolter
Max Hilaire Wolter
Chalcopyrite solar cells achieve efficiencies above 23%. The latest improvements are due to post‐deposition treatments (PDT) with heavy alkalis. This study provides a comprehensive description of the effect of PDT on the chemical and electronic structure of surface and bulk of Cu(In,Ga)Se2. Chemical changes at the surface appear similar, independent of absorber or alkali. However, the effect on the surface electronic structure differs with absorber or type of treatment, although the improvement of the solar cell efficiency is the same. Thus, changes at the surface cannot be the only effect of the PDT treatment. The main effect of PDT with heavy alkalis concerns bulk recombination. The reduction in bulk recombination goes along with a reduced density of electronic tail states. Improvements in open‐circuit voltage appear together with reduced band bending at grain boundaries. Heavy alkalis accumulate at grain boundaries and are not detected in the grains. This behavior is understood by the energetics of the formation of single‐phase Cu‐alkali compounds. Thus, the efficiency improvement with heavy alkali PDT can be attributed to reduced band bending at grain boundaries, which reduces tail states and nonradiative recombination and is caused by accumulation of heavy alkalis at grain boundaries.

4 September 2019 in Nature Communications
Verified
Journal Article
Open access
PDF file
NNNicoleta Nicoara
Nicoleta Nicoara
RMRoby Manaligod
Roby Manaligod
PJPhilip Jackson
Philip Jackson
DHDimitrios Hariskos
Dimitrios Hariskos
WWWolfram Witte
Wolfram Witte
SSSascha Sadewasser
Sascha Sadewasser
The properties and performance of polycrystalline materials depend critically on the properties of their grain boundaries. Polycrystalline photovoltaic materials – e.g. hybrid halide perovskites, copper indium gallium diselenide (CIGSe) and cadmium telluride – have already demonstrated high efficiencies and promise cost-effective electricity supply. For CIGSe-based solar cells, an efficiency above 23% has recently been achieved using an alkali-fluoride post-deposition treatment; however, its full impact and functional principle are not yet fully understood. Here, we show direct evidence for the passivation of grain boundaries in CIGSe treated with three different alkali-fluorides through a detailed study of the nanoscale optoelectronic properties. We determine a correlation of the surface potential change at grain boundaries with the open-circuit voltage, which is supported by numerical simulations. Our results suggest that heavier alkali elements might lead to better passivation by reducing the density of charged defects and increasing the formation of secondary phases at grain boundaries.

1 October 2006 in Organic Electronics
Verified
Journal Article
Closed access
NNNicoleta Nicoara
Nicoleta Nicoara
ERElisa Román
Elisa Román
JGJosé M. Gómez-Rodríguez
José M. Gómez-Rodríguez
JMJosé A. Martín-Gago
José A. Martín-Gago
Javier MéndezJavier Méndez
Javier Méndez

27 January 2017 in Scientific Reports
Verified
Journal Article
Open access
PDF file
NNN. Nicoara
N. Nicoara
TLTh. Lepetit
Th. Lepetit
LAL. Arzel
L. Arzel
SHS. Harel
S. Harel
NBN. Barreau
N. Barreau
SSSascha Sadewasser
Sascha Sadewasser
Significant power conversion efficiency improvements have recently been achieved for thin-film solar cells based on a variety of polycrystalline absorbers, including perovskites, CdTe, and Cu(In,Ga)Se2(CIGS). The passivation of grain boundaries (GBs) through (post-deposition) treatments is a crucial step for this success. For the case of CIGS, the introduction of a potassium fluoride post-deposition treatment (KF-PDT) has boosted their power conversion efficiency to the best performance of all polycrystalline solar cells. Direct and indirect effects of potassium at the interface and interface-near region in the CIGS layer are thought to be responsible for this improvement. Here, we show that also the electronic properties of the GBs are beneficially modified by the KF-PDT. We used Kelvin probe force microscopy to study the effect of the KF-PDT on the CIGS surface by spatially resolved imaging of the surface potential. We find a clear difference for the GB electronic properties: the KF-PDT increases the band bending at GBs by about 70% and results in a narrower distribution of work function values at the GBs. This effect of the KF-PDT on the GB electronic properties is expected to contribute to the improved efficiency values observed for CIGS thin-film solar cells with KF-PDT.

4 September 2014 in IEEE Journal of Photovoltaics
Verified
Journal Article
Open access
Bart VermangBart Vermang
Bart Vermang
JWJorn Timo Watjen
Jorn Timo Watjen
CFChristopher Frisk
Christopher Frisk
VFViktor Fjallstrom
Viktor Fjallstrom
FRFredrik Rostvall
Fredrik Rostvall
SSSascha Sadewasser
Sascha Sadewasser
Recently, Cu(In,Ga)Se 2 (CIGS) solar cells have achieved 21% world-record efficiency, partly due to the introduction of a postdeposition potassium treatment to improve the front interface of CIGS absorber layers. However, as high-efficiency CIGS solar cells essentially require long diffusion lengths, the highly recombinative rear of these devices also deserves attention. In this paper, an Al 2 O 3 rear surface passivation layer with nanosized local point contacts is studied to reduce recombination at the standard Mo/CIGS rear interface. First, passivation layers with well-controlled grids of nanosized point openings are established by use of electron beam lithography. Next, rear-passivated CIGS solar cells with 240-nm-thick absorber layers are fabricated as study devices. These cells show an increase in open-circuit voltage (+57 mV), short-circuit current (+3.8 mA/cm 2 ), and fill factor [9.5% (abs.)], compared with corresponding unpassivated reference cells, mainly due to improvements in rear surface passivation and rear internal reflection. Finally, solar cell capacitance simulator (SCAPS) modeling is used to calculate the effect of reduced back contact recombination on high-efficiency solar cells with standard absorber layer thickness. The modeling shows that up to 50-mV increase in open-circuit voltage is anticipated.

9 November 2020 in Advanced Optical Materials
Verified
Journal Article
Closed access
PDF file
MCMarcel S. Claro
Marcel S. Claro
JGJustyna Grzonka
Justyna Grzonka
NNNicoleta Nicoara
Nicoleta Nicoara
PFPaulo J. Ferreira
Paulo J. Ferreira
SSSascha Sadewasser
Sascha Sadewasser