19 September 2025 in IEEE Solid-State Circuits Letters
Capacitive touch screens have become the dominant user interface over the past decade. Achieving high framerates with low power consumption remains a critical design goal for touch systems. The conventional charge-recycling technique reduces driving power by 64%, but it relies on off-chip capacitors. To address this issue, we propose a tri-level energy recycling scheme, in which energy released during the 2-to-1 transition is recycled to power the 0-to-1 transition on the complementary channel. This approach achieves a 25% power reduction using on-chip transmission gates. Additionally, a compressive sensing method is introduced to selectively process touched RX channels while bypassing the others, reducing the number of fine ADCs by a factor of four compared to conventional two-step sensing. The proposed techniques are implemented in a 65 nm CMOS process and integrated into a 32×20 channel prototype occupying 2.4 mm. Measurement results show that the chip consumes only 2.6 mW at a framerate of 1513 Hz. The signal-to-noise ratio (SNR) reaches 49.7 dB for finger touch and 28.7 dB for a 1 mm Φ stylus, resulting in an energy efficiency of 10.66 pJ/step.
30 July 2025 in IEEE Transactions on Circuits and Systems I: Regular Papers
Radio frequency (RF) power-harvesting technology is widely used by the temperature sensors inside high-voltage power-distribution cabinets, which avoids the safety risks caused by the use of batteries. Although the RF electromagnetic wave generated by high-voltage electric fields inside the cabinet can serve as the power supply, it suffers from unstable energy density. As a result, an external device is usually required to power up and read the temperature sensor, such as the near-field communication (NFC) reader of a smartphone. In this case, the RF harvester of the temperature sensor should be sensitive enough to enable a safe operating distance between the external reader and cabinet. Traditional methods combined an AC-DC rectifier and a DC-DC converter to provide a sufficient-high supply voltage for the sensing circuits, but the sensitivity was limited to −21dBm. In this work, an oscillator-enhanced energy-fusion power-harvesting technique is proposed to extend the power-transfer range of NFC. The harvester picks up the NFC energy to start up an oscillator, which enhances the power-harvesting sensitivity of other RF electromagnetic waves such as the 433MHz component in the cabinet. Then, the harvested DC voltage can be increased due to the power superposition of both the 13.56MHz and 433MHz tones. The proposed technique is implemented in a power-harvesting chipset fabricated in 55nm CMOS and 65nm CMOS processes. Measurement results show that the sensitivity of 433MHz power harvester is improved by 4.1dB due to the enhancement of the NFC excited oscillator, which also extends the NFC power-transfer range to 9cm.
10 June 2025 in IEEE Journal of Solid-State Circuits
Capacitive touch-screen systems have been widely used in tablets, smartphones, smartwatches, etc. Various sources of noise, such as display and charger noise, limit the energy efficiency of capacitive touch sensors. Traditional noise-reduction methods such as lock-in sensing architecture lead to significant power consumption that shortens the lifetime of battery-powered devices. To address the issue, we propose a noise transfer function (NTF)-alignment technique, in which the excitation signals are precisely placed at the zeros of NTF and the touch-screen system noise lies between them. In addition, a subsequent direct lock-in analog-to-digital converter (ADC) with bandpass noise shaping utilizes the same NTF zeros as the excitation source, resulting in a high signal-to-noise ratio (SNR) throughout the entire signal chain. This simple structure also eliminates bandpass filters, mixers, and low-pass filters in conventional lock-in sensing chains. The proposed techniques are implemented in a 65-nm CMOS process, demonstrating a touch-screen prototype embedded with a 28-channel chip occupying an area of 1.31 mm2. The measured results show that the chip achieves an SNR of 58.9 (for 10-mm $\Phi $ ) and 41.3 dB (for 1-mm $\Phi $ stylus), with only 1.054-mW power dissipated at 120 frames/s. Compared to state-of-the-art designs, the proposed chip achieves the best energy efficiency (27.2 pJ/step).