10 May 2024 in IEEE Sensors Journal
The increasing demand for efficient and sustainable agricultural practices underscores the importance of Agriculture Internet-of-Things (Agri-IoT). This integration of technology in agriculture facilitates precise and efficient farming methods, contributing significantly to global food security and environmental conservation. For Agri-IoT optimization, it is essential to obtain information such as temperature, ambient humidity (AH) and soil moisture (SM) in an environment-friendly manner. The existing sensor node is powered by battery that can potentially pollute the soil and have limited lifespan. In this work, we present a sensor chip that can efficiently read in temperature, AH and SM in an all-dynamic manner. The multi-parameter chip operates in an event-driven manner, which only starts wireless transmission if an input event is detected. The event-driven operation further reduces the energy consumption of the sensor node. The low-energy sensor is combined with RF energy harvester and wireless transmitter to achieve battery-less data acquisition. The proposed sensor chip is fabricated in 65-nm CMOS technology and occupies a chip area of 0.612mm 2 . The measured temperature accuracy is ±1°C over the range of -40 to 85°C with a single-point calibration. The measured ambient humidity ±3.8 %RH over the 10-90 %RH range. Besides, it can support soil moisture monitoring over the range of 10-50 % gravimetric water content. The power consumption of the multi-sensor interface circuits is 4.8 μW at a supply voltage of 0.8 V.
23 January 2024 in IEEE Journal of Solid-State Circuits
The growing trend of the Internet of Things (IoT) involves trillions of sensors in various applications. An extensive array of parameters need to be gathered concurrently with high-precision, low-cost, and low-power sensor nodes, such as resistive (R) and capacitive (C) sensors. Single-chip channel fusion can be an effective solution, while it is challenging to suppress the noise and integrate massive I/O pads. However, conventional oversampling noise-shaping methods increase power consumption, which fails to meet the demand of long-term monitoring applications. In addition, existing R/C sensor-interface chips require a pair of I/O pads for each sensor, where the pad frame dominates the overall chip area in massive-channel integration. In this work, we demonstrate a 72-channel R&C sensor-interface chip for proximity-and-temperature sensing. A noise-orthogonalizing technique is proposed to eliminate the quantization noise at the signal frequencies, achieving an energy efficiency of 19.1 pJ/step/channel. Moreover, a pad-sharing technique is proposed to reduce the number of I/O pads by half, enabling 72 sensors to be read by 36 pairs of I/O pads. The chip is fabricated by 65-nm CMOS technology, and measurement results show resolutions of 286 $\Omega $ and 162 fF, respectively. The power consumption and die area are reduced to 0.74 $\mu \text{W}$ /Channel and 0.038 mm2/Channel, respectively.
21 June 2022 in IEEE Transactions on Circuits and Systems II: Express Briefs
DNA analyzing technologies are commonly used in prevention and treatment of various infectious diseases. A portable DNA analyzer based on impedance spectroscopy facilitates the testing, while low pow consumption is necessary to minimize the battery size. However, traditional impedance spectroscopy techniques utilize power-hungry sinusoid signal to stimulate the DNA sample. In this brief, we demonstrate a DNA analyzer chip with square-wave stimulation and detection. The spectral aliasing induced by the harmonics of square wave is avoided by a half-integer over-sampling technique. In this way, the chip eliminates the requirement of power-hungry filters in conventional works. In addition, the impedance spectroscopy corresponding to the $3^{rd}$ harmonic is utilized to provide an extra stimulus frequency, enabling simultaneous DNA analysis at two frequencies. Fabricated in 65nm CMOS process, the in-vitro DNA testing data of our chip matches favorably with the results of an electrochemical workstation (CHI760E). The proposed DNA analyzer chip consumes $120\mu \text{W}$ power, and doubles the analyzing speed by the $3^{rd}$ harmonic based detection.
19 September 2025 in IEEE Solid-State Circuits Letters
Capacitive touch screens have become the dominant user interface over the past decade. Achieving high framerates with low power consumption remains a critical design goal for touch systems. The conventional charge-recycling technique reduces driving power by 64%, but it relies on off-chip capacitors. To address this issue, we propose a tri-level energy recycling scheme, in which energy released during the 2-to-1 transition is recycled to power the 0-to-1 transition on the complementary channel. This approach achieves a 25% power reduction using on-chip transmission gates. Additionally, a compressive sensing method is introduced to selectively process touched RX channels while bypassing the others, reducing the number of fine ADCs by a factor of four compared to conventional two-step sensing. The proposed techniques are implemented in a 65 nm CMOS process and integrated into a 32×20 channel prototype occupying 2.4 mm. Measurement results show that the chip consumes only 2.6 mW at a framerate of 1513 Hz. The signal-to-noise ratio (SNR) reaches 49.7 dB for finger touch and 28.7 dB for a 1 mm Φ stylus, resulting in an energy efficiency of 10.66 pJ/step.
30 July 2025 in IEEE Transactions on Circuits and Systems I: Regular Papers
Radio frequency (RF) power-harvesting technology is widely used by the temperature sensors inside high-voltage power-distribution cabinets, which avoids the safety risks caused by the use of batteries. Although the RF electromagnetic wave generated by high-voltage electric fields inside the cabinet can serve as the power supply, it suffers from unstable energy density. As a result, an external device is usually required to power up and read the temperature sensor, such as the near-field communication (NFC) reader of a smartphone. In this case, the RF harvester of the temperature sensor should be sensitive enough to enable a safe operating distance between the external reader and cabinet. Traditional methods combined an AC-DC rectifier and a DC-DC converter to provide a sufficient-high supply voltage for the sensing circuits, but the sensitivity was limited to −21dBm. In this work, an oscillator-enhanced energy-fusion power-harvesting technique is proposed to extend the power-transfer range of NFC. The harvester picks up the NFC energy to start up an oscillator, which enhances the power-harvesting sensitivity of other RF electromagnetic waves such as the 433MHz component in the cabinet. Then, the harvested DC voltage can be increased due to the power superposition of both the 13.56MHz and 433MHz tones. The proposed technique is implemented in a power-harvesting chipset fabricated in 55nm CMOS and 65nm CMOS processes. Measurement results show that the sensitivity of 433MHz power harvester is improved by 4.1dB due to the enhancement of the NFC excited oscillator, which also extends the NFC power-transfer range to 9cm.
10 June 2025 in IEEE Journal of Solid-State Circuits
Capacitive touch-screen systems have been widely used in tablets, smartphones, smartwatches, etc. Various sources of noise, such as display and charger noise, limit the energy efficiency of capacitive touch sensors. Traditional noise-reduction methods such as lock-in sensing architecture lead to significant power consumption that shortens the lifetime of battery-powered devices. To address the issue, we propose a noise transfer function (NTF)-alignment technique, in which the excitation signals are precisely placed at the zeros of NTF and the touch-screen system noise lies between them. In addition, a subsequent direct lock-in analog-to-digital converter (ADC) with bandpass noise shaping utilizes the same NTF zeros as the excitation source, resulting in a high signal-to-noise ratio (SNR) throughout the entire signal chain. This simple structure also eliminates bandpass filters, mixers, and low-pass filters in conventional lock-in sensing chains. The proposed techniques are implemented in a 65-nm CMOS process, demonstrating a touch-screen prototype embedded with a 28-channel chip occupying an area of 1.31 mm2. The measured results show that the chip achieves an SNR of 58.9 (for 10-mm $\Phi $ ) and 41.3 dB (for 1-mm $\Phi $ stylus), with only 1.054-mW power dissipated at 120 frames/s. Compared to state-of-the-art designs, the proposed chip achieves the best energy efficiency (27.2 pJ/step).