1 August 2019 in Construction and Building Materials
14 March 2019 in Road Materials and Pavement Design
Aggregate–binder adhesiveness in asphalt mixtures is affected by the physico-chemical properties of aggregates and asphalt binder. The objective of this paper is to analyse how aggregate morphological and physico-chemical properties affect the aggregate–binder adhesiveness measured by different techniques. Two aggregate sources (granitic and phonolitic) combined with two asphalt binders (a neat binder and the same binder modified by an anti-stripping agent) were used. Grounded plastic bags were also used as an additive to improve aggregate–binder interface properties. The adhesiveness test used follows ABNT 12583 (similar to static water storage according to EN 12697-11B) and subsequent digital image processing (DIP), developed in a previous work. Absorption was measured by a classical immersion weighting procedure (DNER 081), while angularity and texture were determined using the Aggregate Image Measurement System (AIMS). Aggregate’s chemical composition was investigated by X-Ray Fluorescence. Moisture-induced damage resistance was determined by the modified Lottman test (ABNT 15617). Asphalt Bond Strength (ABS) tests were performed with different water conditioning times. DIP allowed correlating adhesiveness to different parameters, such as angularity, texture, porosity and oxide content of the aggregate, and also to moisture-induced damage test results and the ABS test results. Results show that the granitic aggregate presented better adhesiveness with both the neat binder and the binder with anti-stripping agent. The mixture with grounded plastic bags also had better adhesiveness when compared to the control mixture. Aggregate’s angularity, texture and porosity do not appear to affect aggregate–binder adhesiveness, whereas Fe2O3 and CaO content presented excellent correlations with the adhesiveness test analysed by DIP. The asphalt film dislocation test analysed by DIP also presented strong correlation with the moisture-induced damage test. It seems possible to establish a reliable limit for DIP results in this simple test to prevent mixtures of being susceptible to moisture damage.
15 January 2021 in International Journal of Pavement Engineering
Aggregate-binder adhesiveness is a property that can affect the service life of asphalt pavements. In order to reduce the effects of the loss of adhesion between aggregates and binders over time, lime or amine-based anti-stripping agents are commonly used. The objective of this paper is to evaluate the impact of using an amine-based anti-stripping agent on the fatigue life of asphaltic pavements. Stiffness characterisation, the Simplified Viscoelastic Continuum Damage model, and the software FlexPAVE™ were used. Two different layered structures were analysed: one with a 0.10 m asphalt layer thickness, and another with a combination of two 0.05 m asphalt layers, with the same 0.10 m total asphalt layers thickness. The 10 years fatigue simulation was considered with 1,000,100 total ESALs traffic volume, single wheel loading of 40 kN, traffic speed of 60 km/h, and constant temperature of 20°C. It was concluded that mixtures with anti-stripping agent and/or granitic aggregate showed better fatigue behaviour than mixtures with neat binder and/or phonolitic aggregate. All investigated pavements showed bottom-up predicted crack initiation. It is more recommended to use the mixtures with amine-based anti-stripping agent on the bottom asphalt layer and mixtures with neat binder on the top layer.
31 July 2019 in Journal of Testing and Evaluation
The adhesiveness between aggregate and asphalt binder is believed to affect the life cycle of asphalt pavements, mainly in the presence of water. One of the most common asphalt pavement distresses is fatigue cracking. The objective of this article is to investigate the relationship between adhesion properties and fatigue life of asphalt mixtures. The asphalt bond strength test was used to measure adhesion (pull-off tensile strength) at two different moisture conditioning states: unconditioned (or dry) and conditioned in distilled water for 24 h at 40°C. The test consists of measuring the pull-off pressure required to break an aggregate–binder interface, called the pull-off tensile strength. For the fatigue damage characterization of the mixtures, controlled crosshead sinusoidal tension-compression tests were used, associated with the Simplified Viscoelastic Continuum Damage modeling protocol. Four asphalt mixtures were investigated. They share the same aggregate gradation but differ in aggregate source (two different sources) and the presence or absence of an anti-stripping agent. The mixture with pure asphalt binder showed higher values of pull-off tensile strength than mixtures with asphalt binder doped by an anti-stripping agent. However, the analysis of the pull-off tensile strength ratio (comparison between unconditioned and moisture-conditioned specimens) showed that the addition of anti-stripping agent provided significant moisture damage resistance in the aggregate–binder interface. Results also show that mixtures with asphalt binder modified by anti-stripping agent had higher simulated fatigue life than mixtures with pure asphalt binder. Excellent correlations were obtained between the strain amplitude required to obtain a given @ Nf (strain amplitude @ Nf) with pull-off tensile strength, which confirms that the fatigue life of asphalt mixtures is related to the adhesion between aggregate and asphalt binder.
16 April 2020 in Materials and Structures
16 June 2021 in The Journal of Adhesion
Adhesiveness is a property that directly affects the service life of asphalt pavements. Over the years, different materials, research methods and tests have been used to investigate different adhesiveness aspects of materials. This paper investigated two asphalt binders, one with and one without amine-based anti-stripping agent, as well as two aggregate sources. The objective was to investigate the effects of rheology (stiffness and rutting) of the asphalt binder and adhesiveness of asphalt binders to different substrates on the resistance to moisture conditioning. The results indicated that moisture conditioning reduced the average stiffness of the binders by about 15% for both binders. The addition of amine-based anti-stripping agent reduced the stiffness of the neat binder by approximately 9%, and at 82°C the neat binder presented higher rutting resistance if compared to the modified binder using anti-stripping agent. The aggregate area within the HMAs in contact with asphalt binder did not show a good correlation with the pull-off tensile strength in the dry condition, but it presented good correlation after moisture conditioning. This suggests that adhesion force itself may not be greatly affected by the proper contact between aggregate and binder, but such contact does help preventing moisture damage in the interface.