Juris Smirnovs

Juris Smirnovs

Auto-generated profile, based on publicly available information

Juris Smirnovs

Department of Roads and Bridges, Transportation Engineering Institute, Faculty of Civil Engineering, Riga Technical University, Riga, Latvia

Research Focus & Metrics

Academic Career Length

18Years (2009-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2016 in Transportation Research Procedia
Verified
Journal Article
Open access
VHViktors Haritonovs
Viktors Haritonovs
JTJanis Tihonovs
Janis Tihonovs
JSJuris Smirnovs
Juris Smirnovs
Dolomite is one of the most widely available sedimentary rocks in the territory of Latvia. Dolomite quarries contain about 1,000 million tons of this material. However, according to Latvian Road Specifications, this dolomite cannot be used for average and high intensity roads because of its low quality, mainly, its LA index (The Los Angeles abrasion test). Therefore, mostly the imported magmatic rocks (granite, diabase, gabbro, basalt) or imported dolomite are used, which makes asphalt expensive. However, practical experience shows that even with these high quality materials roads exhibit rutting, fatigue, and thermal cracks. The aim of the research is to develop a high performance asphalt concrete for base and binder courses using only locally available aggregates. In order to achieve resistance against deformations at a high ambient temperature, a hard grade binder was used. Workability, fatigue and thermal cracking resistance, as well as sufficient water resistance is achieved by low porosity (3-5%) and higher binder content compared to traditional asphalt mixtures. The design of the asphalt includes a combination of empirical and performance based tests, which in laboratory circumstances allow simulating traffic and environmental loads. High performance AC 16 base asphalt concrete was created using local dolomite aggregate with polymer modified (PMB 10/40-65) and hard grade (B20/30) bitumen. The mixtures were specified based on fundamental properties in accordance with EN 13108-1 standard

17 October 2012 in The Baltic Journal of Road and Bridge Engineering
Verified
Journal Article
Closed access
MZMartins Zaumanis
Martins Zaumanis
EOEric Olesen
Eric Olesen
VHViktors Haritonovs
Viktors Haritonovs
GBGuntis Brencis
Guntis Brencis
JSJuris Smirnovs
Juris Smirnovs
Warm mix asphalt (WMA) technologies allow significant lowering of the production and paving temperature of the conventional hot mix asphalt (HMA), which promise various benefits, e.g. lowering the greenhouse gas emissions, reduction of energy consumption, improved working conditions, better workability and compaction, etc. However, in order to reach widespread implementation of WMA, it is necessary to prove that it has the same or better mechanical characteristics and long-term performance as HMA. This article presents a laboratory study that has been conducted to evaluate two different WMA technologies ? chemical (using Rediset WMX) and organic (using Sasobit) for the use with stone matrix asphalt (SMA). The properties of two types of bitumen after modification with two different dosages of each WMA additive have been tested by traditional empirical test methods and with the Dynamic Shear Rheometer for a wide temperature range. Asphalt testing has been performed for SMA11 type mixture. At first, the necessary changes in testing conditions were determined by means of asphalt stiffness ? the results suggested that for adequate comparison with reference HMA, at least two hour asphalt aging is essential before preparing test specimens. The properties of asphalt were determined for specimens that were prepared at four different compaction temperatures by means of two compaction methods ? Marshall hammer and gyratory compactor. The test results show that it is possible to reduce the compaction temperature of 155 ?C for HMA to at least 125 ?C for both WMA products with maintaining similar density and mechanical characteristics at intermediate to high temperatures.

14 August 2020 in The Baltic Journal of Road and Bridge Engineering
Verified
Journal Article
Open access
PDF file
ABAndrius Baltrušaitis
Andrius Baltrušaitis
AVAudrius Vaitkus
Audrius Vaitkus
JSJuris Smirnovs
Juris Smirnovs
The assurance of asphalt pavement layer compaction, expressed by ratio between field and laboratory bulk density and air voids content, is one of the main criteria of the durability of asphalt road pavement. Destructive measures should be applied and cores should be taken from the asphalt pavement seeking to determine the representative compaction level of the constructed asphalt layers. New methods are constantly being sought for fast, non-destructive and accurate asphalt layer density and air void determination on road. Ground Penetrating Radar (GPR) can allow determining the qualitative characteristics of asphalt pavement across the entire length of the road without causing damage to the road structure. Relative dielectric permittivity, usually called dielectric value or constant, is the leading property used in GPR applications on road pavement surveys. This article presents GPR measurement results from asphalt base and binder layers of four test sections. GPR measurements were conducted immediately after the end of asphalt layer compaction process. Test points on each layer were selected and density, air void content were determined by drilling cores and testing them in the laboratory. To estimate asphalt layer density and air void content, GPR data were analysed using different existing mathematical models. To justify the reliability of the data measured by GPR, results were checked by comparing them with the results measured directly on cores taken from the asphalt pavement layers.

20 April 2013 in The Baltic Journal of Road and Bridge Engineering
Verified
Journal Article
Closed access
VHViktors Haritonovs
Viktors Haritonovs
MZMartins Zaumanis
Martins Zaumanis
GBGuntis Brencis
Guntis Brencis
JSJuris Smirnovs
Juris Smirnovs
The rapid growth of traffic loads in Latvia increases the demands for asphalt carrying capacity on large motorways. The dolomite and sandstone that can be found in Latvia lacks the mechanical strength and for most of the large motorways the aggregates are imported from other countries causing increase of costs and growth of emissions from transportation. On the other hand, large amounts of Basic Oxygen Furnace (BOF) steel slag aggregates with good qualities are being produced in Latvia and put to waste. During the recent decades, the dolomite sand waste has also been accumulated and its quantity has reached a million of tons and is rapidly increasing. This huge quantity of technological waste needs to be recycled with max efficiency. The lack of experience in the use of steel slag and dolomite sand waste requires an accelerated evaluation of the asphalt performance-based characteristics. This paper presents the testing results of dense graded asphalt concrete AC 11 mixtures made of four types of aggregate: steel slag, dolomite sand waste, conventional imported dolomite aggregates and conventional local crushed quartz sand that were proportioned to develop a mixture that would satisfy the requirements of permanent deformation and stiffness. Analysis of the results showed that the mixes with steel slag and dolomite waste sand or unconventional aggregate combination with dolomite in coarse portion, crushed quartz sand in sand portion plus dolomite waste sand in sand and filler portions had high resistance to plastic deformations and fatigue failure. These mixes can fully satisfy and in some cases significantly overcome the requirements of local asphalt specifications for highly loaded motorways.

20 January 2010 in The Baltic Journal of Road and Bridge Engineering
Verified
Journal Article
Closed access
VHViktors Haritonovs
Viktors Haritonovs
JSJuris Smirnovs
Juris Smirnovs
JNJuris Naudžuns
Juris Naudžuns
Asphalt pavement in actual circumstances is subjected to the repetitive and changing transport load. As a result of the repetitive load impact, both elastic and plastic deformations occur to the pavement. Accumulation of plastic deformations in one or several layers leads to appearance of permanent deformations or rutting. This type of deformations reduces safety and convenience of traffic. Aim of the research is investigation of the rutting dynamics on the dense graded asphalt concrete (AC) and stone mastic asphalt (SMA) mixtures. The research has been made by using the standard performance test method

1 December 2012 in Journal of Testing and Evaluation
Verified
Journal Article
Closed access
VHViktors Haritonovs
Viktors Haritonovs
MZMartins Zaumanis
Martins Zaumanis
GBGuntis Brencis
Guntis Brencis
JSJuris Smirnovs
Juris Smirnovs
The rapid growth of transport load in Latvia increases the demands for asphalt carrying capacity on large motorways. The limestone and sandstone that can be found in Latvia lack the mechanical strength and, for most of the large motorways, the aggregates are imported from other countries causing increase of the costs and growth of emissions from transportation. On the other hand, large amounts of basic oxygen furnace (BOF) steel slag aggregates with good qualities are being produced in Latvia and put to waste. During recent decades, the dolomite sand waste has been accumulating and its quantity has reached a million tons and is rapidly increasing. This huge quantity of technological waste needs to be recycled with maximum efficiency. The lack of experience on the use of steel slag and sand waste requires an accelerated evaluation of the asphalt performance-based characteristics. This paper presents the testing results of different combinations of steel slag, dolomite sand waste, and local limestone aggregates that were proportioned to develop a mixture that would satisfy the requirements of permanent deformation and fatigue. Analysis of the results showed that mixes with steel slag and local limestone in coarse portion and dolomite sand waste in sand and filler portions had high resistance to plastic deformations and good resistance to fatigue failure. These mixes can fully satisfy and, in some cases, significantly overcome the requirements of local asphalt specifications for highly loaded motorways.