Wide bandgap two-dimensional semiconductors are of paramount importance for developing van der Waals heterostructure electronics. This work reports the use of layer and strain engineering to introduce the feasibility of two-dimensional hexagonal (h)-AlN to fill the scientific and application gap. We show that such one- to five-layer h-AlN has an indirect bandgap, tunable from 2.9 eV for a monolayer to ∼3.5 eV for multilayer structures, along with isotropic effective masses and carrier mobilities between zigzag and armchair directions. With an increase in the layer number to bulk AlN, the bandgap will experience a transition from an indirect gap to direct gap. Surprisingly, high room-temperature mobilities of electrons and holes (of the order of 1000 cm2 V−1 s−1) in a relaxed monolayer h-AlN system and widely adjustable effective masses and carrier mobilities in a different layer h-AlN are observed. In the presence of strain engineering, the bandgap decreases obviously with an increase in tensile strain; meanwhile, the isotropy and value of effective mass or carrier mobility in monolayer h-AlN can also be modulated effectively; the hole mobilities in the armchair direction, especially, will be enhanced dramatically. With a tunable bandgap, high carrier mobilities, and modifiable isotropy, our results indicate that few-layer h-AlN has potential applications in future mechano-electronic devices.
1 October 2021 in IEEE Transactions on Electron Devices
This article presents a high quality factor ( ${Q}$ ) load sensor based on Sc 0.2 Al 0.8 N/aluminum nitride (AlN)-on-silicon surface acoustic wave (SAW) resonator. Finite element method (FEM) analysis is performed to predict the resonance frequency and the wave propagation mode. A high- ${Q}$ of 7200 at the parallel resonance frequency ( ${f}_{p}$ ) of 447.50 MHz is measured for Sc 0.2 Al 0.8 N/AlN configured SAW resonator on a silicon substrate. Experimental values for variation of series resonance frequency ( ${\Delta } {f}_{s}$ ) and variation of ${f}_{p}$ ( ${\Delta } {f}_{p}$ ) are found to be −75.3 and −186.8 kHz with variation of applied force $({\Delta } \textit {F)} = 4.155$ N, operating in the analyzed range. The linear approximation of measured frequency variations under force is ${\Delta } {f}_{s}/{F} = -12.7$ kHz/N and ${\Delta } {f}_{p}/{F} = -46.2$ kHz/N. Moreover, the force sensitivities for this sensor are −28.4 and −103.2 ppm/N for ${f}_{s}$ and ${f}_{p}$ , respectively. This high- ${Q}$ scandium-doped AlN (ScAlN)/AlN-based SAW resonator exhibits high sensitivity, demonstrating that the structure can be used as load sensors in industrial applications such as manufacturing, medical, grocery, and automotive industries.
5 April 2023 in Journal of Microelectromechanical Systems
The demand for filters with a large fractional bandwidth, up to 5%, still puts a great challenge to the typical aluminum nitride (AlN) thin films-based bulk acoustic wave (BAW) filters in an acoustic-only approach. This paper presents the design, fabrication, and characterization of film bulk acoustic wave resonator (FBAR) and filters using aluminum scandium nitride (Al $_{0.8}$ Sc $_{0.2}$ N) thin films. The fundamental thickness-mode resonance of the FBAR is measured at 4.235 GHz with an excellent effective electromechanical coupling factor ( $K_{eff}^{2})$ of 14%. The filters employ a modified structure with additional $\vphantom{^{\int}}$ molybdenum (Mo) layers formed on the connection strips between each adjacent resonator. The proposed filtering topologies including ladder topology, lattice topology, and ladder-lattice topology are constructed. Results show that the modified connection strips can decrease the magnitude impedance at series resonant frequency and improve the insertion loss (IL) of the filters. The fabricated ladder filter demonstrates a high center frequency of 4.25GHz, low IL of 1.804 dB, wide bandwidth of 189 MHz, and out-of-band rejection of 30 dB, holding a great potential for the 5G wideband applications. 2022-0201
Bulk acoustic wave (BAW) filters have been extensively used in consumer products for mobile communication systems due to their high performance and a standard CMOS compatible integration process. However, a traditional BAW filter generally presents only one frequency transmission band; hence, it cannot meet the demands of multi-mode wireless communication systems. In this work, we propose a radio frequency dual-band filter based on a dual-mode film bulk acoustic resonator (FBAR). The dual-mode FBAR consists of molybdenum electrodes and an aluminum nitride film with a c axis tilt angle, which leads to the coexistence of the longitudinal mode and the shear mode in the resonator. The influence of the tilt angle on the resonant frequency and electromechanical coupling coefficient of the dual-mode FBAR is investigated. Subsequently, the behaviors of the dual-mode FBAR have been emulated by a modified Butterworth–Van Dyke model with two motional branches, which is further used to design and optimize the dual-band filter. The dual-mode FBAR-based filters connected in a ladder configuration present two dual passbands of 43 MHz and 105 MHz, respectively. The developed filters with dual passbands can give an inspiration to the design of BAW devices in modern wireless communications.
In this paper, 600nm Z-cut lithium niobate (LiNbO 3 ) thin film based third-order antisymmetric (A3) mode resonators with different geometries has been investigated. Through a series of experiments, it has been found for the first time that effective electromechanical coupling coefficient (K eff2 ) is influenced by the gap between electrodes (Ge), and K eff2 decreases with the increase of Ge when electrode pitch (P) higher than 5μm. Finally, a A3 mode resonator with a high 2 Keff of 6.72% is obtained. This K eff2 is the highest reported value in similar acoustic resonators working about 9 GHz and will be beneficial to the construction of X-band filters.
The thin film bulk acoustic resonator (FBAR) has emerged as a promising choice for liquid sensors because of its high frequency and sensitivity. To investigate the potential of FBAR devices working as the liquid sensors, we study the operating law of FBAR in liquid environments and explore the different loading effects of liquid on the shear mode and longitudinal mode. By analyzing the device and liquid interactions, we modify the Mason model of FBAR in the liquid environment. Subsequently, the influence of the piezoelectric film with different tilt angles and liquids on the characteristics of FBAR is discussed. We also prepared Sc0.2Al0.8N film-based FBAR to confirm the influence of different liquid environments on the resonant performances. The results show that the frequency drift of FBAR in the shear mode is related to density and viscosity of liquid, and the frequency drift of FBAR in the longitudinal mode is related to bulk modulus and density of liquid. The resonant frequency of FBAR in the shear mode is more sensitive with glycerol solution than that of FBAR in the longitudinal mode. This work can provide a research basis for the application of FBAR liquid sensors.