Negative triangularity (NT) is a potentially transformative configuration for tokamak-based fusion energy with its high-performance core, edge localized mode (ELM)-free edge, and low-field-side divertors that could readily scale to an integrated reactor solution. Previous NT work on the TCV and DIII-D tokamaks motivated the installation of graphite-tile armor on the low-field-side lower outer wall of DIII-D. A dedicated multiple-week experimental campaign was conducted to qualify the NT scenario for future reactors. During the DIII-D NT campaign, high confinement ( 1), high current ( 3), and high normalized pressure plasmas ( 2.5) were simultaneously attained in strongly NT-shaped discharges with average triangularity = −0.5 that were stably controlled. Experiments covered a wide range of DIII-D operational space (plasma current, toroidal field, electron density and pressure) and did not trigger an ELM in a single discharge as long as sufficiently strong NT was maintained; in contrast, to other high-performance ELM-suppression scenarios that have narrower operating windows. These strong NT plasmas had a lower outer divertor X-point shape and maintained a non-ELMing edge with an electron temperature pedestal, exceeding that of typical L-mode plasmas. Also, the following was achieved during the campaign: high normalized density ( / of at least 1.7), particle confinement comparable to energy confinement with , a detached divertor without impurity seeding, and a mantle radiation scenario using extrinsic impurities. These results are promising for a NT fusion pilot plant but further questions on confinement extrapolation and core-edge integration remain, which motivate future NT studies on DIII-D and beyond.
Strongly-shaped diverted negative triangularity (NT) plasmas in the DIII-D tokamak demonstrate simultaneous access to high normalized density, current, pressure, and confinement. NT plasmas are shown to exist across an expansive parameter space compatible with high fusion power production, revealing surprisingly good core stability properties that compare favorably to conventional positive triangularity plasmas in DIII-D. Non-dimensionalizing the key parameters, expanded operating spaces featuring edge safety factors below 3, normalized betas above 3, Greenwald density fractions above 1, and high-confinement mode (H-mode) confinement qualities above 1 are observed, even simultaneously, and all with a robustly stable edge free from deleterious edge-localized mode instabilities. Scaling of the confinement time with engineering parameters reveals at least a linear dependence on plasma current although with significant power degradation, both in excess of expected H-mode scalings. These results increase confidence that NT plasmas are a viable approach to realize fusion power and open directions for future detailed study.
Laser blow-off injections of aluminum and tungsten have been performed on the DIII-D tokamak to investigate the variation of impurity transport in a set of dedicated ion and electron heating scans with a fixed value of the external torque. The particle transport is quantified via the Bayesian inference method, which, constrained by a combination of a charge exchange recombination spectroscopy, soft x-ray measurements, and vacuum ultraviolet spectroscopy provides a detailed uncertainty quantification of transport coefficients. Contrasting discharge phases with a dominant electron and ion heating reveal a threefold drop in the impurity confinement time and order of magnitude increase in midradius impurity diffusion, when additional electron heating is applied. Furthermore, the calculated stationary aluminum density profiles reverse from peaked in electron heated to hollow in the ion heated case, following a similar trend to electron and carbon density. Comparable values of a core diffusion have been observed for W and Al ions, while differences in the propagation dynamics of these impurities are attributed to pedestal and edge transport. Modeling of the core transport with non-linear gyrokinetics code CGYRO [J. Candy and E. Belly, J. Comput. Phys. 324, 73 (2016)], significantly underpredicts the magnitude of the variation in Al transport. Diffusion increases three-times steeper with additional electron heat flux, and 10-times lower diffusion is observed in ion heated case than predicted by the modeling. The CGYRO model quantitatively matches the increase in the Al diffusion when approaching the linear threshold for the transition from the ion temperature gradient to trapped electron mode.
DIII-D physics research addresses critical challenges for the operation of ITER and the next generation of fusion energy devices. This is done through a focus on innovations to provide solutions for high performance long pulse operation, coupled with fundamental plasma physics understanding and model validation, to drive scenario development by integrating high performance core and boundary plasmas. Substantial increases in off-axis current drive efficiency from an innovative top launch system for EC power, and in pressure broadening for Alfven eigenmode control from a co-/counter-Ipsteerable off-axis neutral beam, all improve the prospects for optimization of future long pulse/steady state high performance tokamak operation. Fundamental studies into the modes that drive the evolution of the pedestal pressure profile and electron vs ion heat flux validate predictive models of pedestal recovery after ELMs. Understanding the physics mechanisms of ELM control and density pumpout by 3D magnetic perturbation fields leads to confident predictions for ITER and future devices. Validated modeling of high-Zshattered pellet injection for disruption mitigation, runaway electron dissipation, and techniques for disruption prediction and avoidance including machine learning, give confidence in handling disruptivity for future devices. For the non-nuclear phase of ITER, two actuators are identified to lower the L–H threshold power in hydrogen plasmas. With this physics understanding and suite of capabilities, a high poloidal beta optimized-core scenario with an internal transport barrier that projects nearly toQ= 10 in ITER at ∼8 MA was coupled to a detached divertor, and a near super H-mode optimized-pedestal scenario with co-Ipbeam injection was coupled to a radiative divertor. The hybrid core scenario was achieved directly, without the need for anomalous current diffusion, using off-axis current drive actuators. Also, a controller to assess proximity to stability limits and regulateβNin the ITER baseline scenario, based on plasma response to probing 3D fields, was demonstrated. Finally, innovative tokamak operation using a negative triangularity shape showed many attractive features for future pilot plant operation.
A one dimensional, absolutely calibrated pinhole camera system was installed on the DIII-D tokamak to measure edge Lyman-alpha (Ly-α) emission from hydrogen isotopes, which can be used to infer neutral density and ionization rate profiles. The system is composed of two cameras, each providing a toroidal fan of 20 lines of sight, viewing the plasma edge on the inboard and outboard side of DIII-D. The cameras’ views lie in a horizontal plane 77 cm below the midplane. At its tangency radius, each channel provides a radial resolution of ∼2 cm full width at half maximum (FWHM) with a total coverage of 22 cm. Each camera consists of a rectangular pinhole, Ly-α reflective mirror, narrow-band Ly-α transmission filter, and a 20 channel AXUV photodetector. The combined mirror and transmission filter have a FWHM of 5 nm, centered near the Ly-α wavelength of 121.6 nm and is capable of rejecting significant, parasitic carbon-III (C-III) emission from intrinsic plasma impurities. To provide a high spatial resolution measurement in a compact footprint, the camera utilizes advanced engineering and manufacturing techniques including 3D printing, high stability mirror mounts, and a novel alignment procedure. Absolutely calibrated, spatially resolved Ly-α brightness measurements utilize a bright, isolated line with low parasitic surface reflections and enable quantitative comparison to modeling to study divertor neutral leakage, main chamber fueling, and radial particle transport.
Quiescent H-mode (QH-mode) has been identified as an attractive stationary operational regime in tokamaks due to its lack of edge localized modes (ELMs), along with good particle and impurity control aided by the presence of magnetohydrodynamic modes such as the edge harmonic oscillation (EHO) or edge turbulence. Experiments on the DIII-D tokamak explore local access conditions for QH-mode through measurements of the critical edge rotational shear necessary for the transition from a QH-mode with a coherent EHO to a typical ELMy H-mode. The critical ExB shear and EHO frequency are predicted by a nonlinear phase-dynamics model relating the pressure and velocity perturbations in the edge pedestal region. The reduced theoretical model predicts a linear relationship between critical shearing rate and c_s⁄√(L_p Δx), where c_s is the ion acoustic velocity, Lp the pressure gradient scale length, and Δx the radial width of the mode. This scaling of the critical shearing rate agrees with the experimental trend, although the absolute magnitude of the shearing rate threshold is over-predicted by the model. Through a normalized predicted scaling, the model demonstrates the dynamic transition into and out of QH-mode qualitatively, within a single plasma discharge. The experimental comparison lends insight into improving the theoretical model by including more accurate geometry and toroidal mode number physics for more accurate quantitative predictions.