18 August 2021 in IEEE Transactions on Power Electronics
Active disturbance rejection control using extended state observer (ESO) is less dependent on the knowledge of the system. It has proved to be an excellent scheme for speed control of electrical drives. However, for time-varying disturbance, the observation precision of conventional ESO is undesired, which limits the speed tracking accuracy. Accordingly, this article proposes an enhanced speed controller for electrical drives based on adaptive switching high-order ESO (ASHESO). First, the critical parameters affecting the steady-state performance of ASHESO are determined according to frequency analytical results. Then, optimized observer gain is obtained by modifying a part of pole locations, which weakens the influence of noise on estimated state. Finally, an adaptive switching gain mechanism is proposed according to the closed-loop tracking error and the swiftness of dynamic response is maintained. The proposed speed controller has achieved high estimation accuracy for disturbance and strong immunity to measurement noise. The feasibility and effectiveness of the strategy is verified on a laboratory permanent magnet synchronous motor (PMSM) drive system.
10 October 2019 in IEEE Transactions on Power Electronics
14 August 2019 in IEEE Transactions on Power Electronics
This paper introduces the classical direct torque control (DTC) to three-phase open-end winding permanent magnet synchronous motor (OEW-PMSM) with common dc bus for the first time. The electromagnetic torque and stator flux are controlled at the same time. However, the zero-sequence current is not suppressed, and the ripples of electromagnetic torque and stator flux are large. To improve the operation performance of this drive system, a DTC based on duty ratio modulation (DRM-DTC) is proposed. Firstly, a deadbeat zero-sequence current controller (DB-ZSCC) is proposed in the DRM-DTC to suppress the zero-sequence current. Secondly, another strategy, which is based on a graphical analysis method and a simple deadbeat direct torque and flux controller (DB-DTFC), is proposed to optimize the duty ratio of active voltage vector. Thus, the electromagnetic torque and stator flux ripples can be reduced. Finally, an optimized PWM implementation strategy is proposed in the DRM-DTC to further reduce the switching frequency of inverters. The classical DTC and the proposed DRM-DTC are compared through simulation and experiment, and the results verify the effectiveness of the proposed strategy.
11 November 2019 in IEEE Transactions on Power Electronics
Owing to simple implementation and excellent performance, the conventional stator flux observer based on active flux concept is considered as a competitive scheme for direct torque control (DTC) system of permanent magnet synchronous motor (PMSM). However, it is constructed by a large number of motor parameters, which may vary with the operating points. This leads to weak robustness. To improve its performance, a stator flux observer with phase self-tuning is proposed as an improved version in this paper. Firstly, relationship between the stator flux observed values obtained by current and voltage models and observed error of rotor position angle are analyzed. Then, according to the above mentioned analysis, a phase self-tuning link constructed by a proportional-integral (PI) regulator is proposed to ensure that the observed coordinate system converge to the actual one even under motor parameters vary conditions. Consequently, the robustness and accuracy of the stator flux observer can be improved. Finally, the stability of the proposed phase self-tuning link is analyzed. Experimental comparison between the conventional stator flux observer based on active flux concept and the proposed improved stator flux observer have been done, and the results verify the feasibility and effectiveness of the proposed stator flux observer.
21 July 2020 in IEEE Transactions on Industrial Electronics
The general rules of rotor pole and armature winding configurations combinations for 24-slot stator wound field flux switching machines (SWFFSMs) are investigated thoroughly in this article. Meanwhile, based on the virtual coil method, a novel general auxiliary evaluation variable, which is proportional to the fundamental amplitude of open-circuit flux-linkage of armature coil is proposed in this article. Hence, these SWFFSMs with larger open-circuit flux-linkage and back-EMF can be obtained effectively. In addition, the effect of rotor poles on the complementarity of armature windings is analyzed so that more sinusoidal and symmetrical back-EMF can be acquired. Furthermore, for these SWFFSMs with larger open-circuit back-EMF, the torque capability is restricted to a considerable extent due to the deep magnetic saturation caused by overlapping armature winding. Hence, a new method by optimizing the ratio of armature slot area and excitation slot area is proposed in this article to ensure that the higher torque density of selected SWFFSMs can be maintained. To verify the validity of analysis and methodology proposed in this article, seven representative SWFFSMs are chosen for verification at no load by the finite-element analysis (FEA) while a 24s/17p SWFFSM with the highest torque density is chosen for further verification at on-load conditions by the FEA and experiments.
10 March 2021 in IEEE Transactions on Industrial Electronics
A novel 24/17-pole 3-phase stator wound field flux switching (SWFFS) machine with the combination of overlapping armature winding (OAW) and asymmetric stator poles (ASP) is proposed for higher torque density in this article. First, the air-gap modulation principle of the 24/17-pole OAW-SWFFS machine is analyzed to better understand its torque production mechanism. Second, since the torque capacity will be greatly restricted by the serious magnetic saturation which is introduced by the OAW configuration, two effective measures are proposed from two perspectives in this article to solve this problem. The first measure is to reduce the magnetic saturation directly by optimizing the area ratio of armature slot and excitation slot, and thus, the torque density can be improved effectively. The second measure is to further enhance the open circuit flux linkages, back electromotive force (EMF), and thus, the torque density by adopting the proposed ASP structure. Furthermore, the accurate ASP distances which are corresponding to the largest back EMF can be obtained effectively based on the air-gap field modulation theory. Finally, the proposed design is validated experimentally by a prototype machine. The simulated and experimental results show that about 25.7% higher torque density can be obtained when compared with 24/14-pole SWFFS machine.