The Al2O3-13 wt.% TiO2 (AT13) composite coatings were prepared on Q235 steel by plasma spray technique. The spray parameters were designed by the orthogonal experiments, and the properties of the coating were evaluated. Results showed that with respect to the bond strength of the coating, the optimized spraying parameters were the plasma current of 530 A, Ar flow of 41 L/min, H2 flow of 10 L/min, and spray standoff distance of 100 mm. The plasma spray process led to the transition of α-Al2O3 to γ-Al2O3, resulting in the increase in the porosity of AT13 coating prepared at nonoptimized parameters. Meanwhile, the porosity and cracks were also increased due to the decrease in the Ar flow and the increase in spray standoff distance. The low porosity, a few cracks, and the uniformly dispersed TiO2 particles contributed the enhanced properties including mechanical and corrosion behaviors of the AT13 coating prepared at optimized parameters. The bond strength, microhardness, and thermal shock resistance of the AT13 coating could reach 25.01 MPa, 1000.6 HV0.5, and 40 times when the coating was prepared at optimized parameters, respectively. Especially, the static Icorr of the AT13 coating prepared at optimized parameters was two order of magnitude less than that of Q235 steel. In addition, the erosion weight loss of Q235 steel could be decreased about 30 times by the protection of the AT13 coating.
Polyimide is type of heterocyclic polymer compound characterized by an imide ring structure. The aromatic ring structure in polyimide facilitates good electrical properties, mechanical properties, thermal properties and radiation resistance, etc. It is widely used in the aerospace field, in electronic components and in the semiconductor industry. Traditional methods for the preparation of polyimide films have different limitations. Here, a new one-step method was established to prepare polyimide coatings using liquid flame spray. The effect of different mass fraction on the surface and cross section structure characteristics of polyimide coatings was studied. The formation process of the polyimide-alumina composite coatings was analyzed using single particles and coatings with different amount of alumina. The composite coating shows a flat and dense structure and excellent dielectric properties. The results shed light on construction of polymer-inorganic composite layers for widespread applications.
Aiming at the wear and corrosion problems of fittings in 500-kV power transmission lines, a functional aluminum-based coating is prepared by an electric arc spraying process and self-made aluminum-based powder-cored wire. The experimental results showed that the friction coefficient of the coating is reduced from 0.4 to 0.2 after adding carbon fiber and that the wear rate is reduced from 2 × 10−3 to 8 × 10−4 mm3/(N·m). The electrochemical behavior of the composite coating is similar to that of the pure aluminum coating. After a 720-h salt spray test, there is no obvious corrosion products on the coating surface, and the thickness of the corrosion layer is only 29 μm. The new composite coating not only has a good anti-wear effect, but also maintains good corrosion resistance of the aluminum coating.
Corrosion is a severe problem for steel structures in humid environments. In particular, humidity usually triggers the surface adhesion of microorganisms, leading to microbiologically induced corrosion. This study aims to explore the effect of bacterial biofilm formation on the pitting corrosion of stainless steel. This research uses electrochemical methods to obtain indirect evidence of the pitting corrosion of steel. In addition, in order to obtain direct evidence of the pitting corrosion of stainless steel, field emission scanning electron microscopy (FESEM) and atomic force microscopy (AFM) were used to characterize the dimensional morphology of the stainless steel after pitting. It was shown that the bacterial adhesion increased with the pH and temperature, which significantly increased the surface roughness of the stainless steel. Electrochemical analysis revealed that the formation of biofilm greatly destroyed the oxide film of 304 SS and accelerated the corrosion of stainless steel by forming an oxygen concentration battery. SEM and AFM analyses showed cracks and dislocations on the surface of stainless steel underneath the attached bacteria, which suggested a direct role of biofilm in corrosion induction. The results presented here show that the bacterial biofilm formation on the steel surfaces significantly accelerated the corrosion and affected the pitting corrosion process of the steel structure.