Petr Svora

Petr Svora

Auto-generated profile, based on publicly available information

Petr Svora

Institute of Physics of the Czech Academy of Sciences, Na Slovance 1999/2, Prague, Czech republic

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
16 October 2023 in Nature Communications
Verified
Journal Article
Open access
PDF file
ESElla Mara Schmidt
Ella Mara Schmidt
PKPaul Klar
Paul Klar
YKYaşar Krysiak
Yaşar Krysiak
PSPetr Svora
Petr Svora
AGAndrew L. Goodwin
Andrew L. Goodwin
LPLukas Palatinus
Lukas Palatinus
Structure-property relationships in ordered materials have long been a core principle in materials design. However, the introduction of disorder into materials provides structural flexibility and thus access to material properties that are not attainable in conventional, ordered materials. To understand disorder-property relationships, the disorder – i.e., the local ordering principles – must be quantified. Local order can be probed experimentally by diffuse scattering. The analysis is notoriously difficult, especially if only powder samples are available. Here, we combine the advantages of three-dimensional electron diffraction – a method that allows single crystal diffraction measurements on sub-micron sized crystals – and three-dimensional difference pair distribution function analysis (3D-ΔPDF) to address this problem. In this work, we compare the 3D-ΔPDF from electron diffraction data with those obtained from neutron and x-ray experiments of yttria-stabilized zirconia (Zr0.82Y0.18O1.91) and demonstrate the reliability of the proposed approach.

15 June 2024 in Additive Manufacturing
Verified
Journal Article
Closed access
ASAngelina Strakosova
Angelina Strakosova
MRMichaela Roudnická
Michaela Roudnická
JŠJiří Šafka
Jiří Šafka
MAMichal Ackermann
Michal Ackermann
DDDrahomír Dvorský
Drahomír Dvorský
PLPavel Lejček
Pavel Lejček

6 September 2025 in Journal of Materials Science
Verified
Journal Article
Open access
PDF file
ASAngelina Strakosova
Angelina Strakosova
DKDaniel Kvapil
Daniel Kvapil
Filip PrůšaFilip Průša
Filip Průša
MVMarek Vronka
Marek Vronka
PSPetr Svora
Petr Svora
DVDalibor Vojtěch
Dalibor Vojtěch
The present work focuses on the characterization of the ultra-high-strength 1.2709 maraging steel produced by the Direct Energy Deposition (DED) technique, either in its as-built or as-built + heat-treated state. Scanning electron microscope micrographs and X-ray diffraction patterns showed that the heat treatment (namely, solution annealing and aging) had minimal impact on the microstructure changes of the maraging steel. The material is characterized by fine cellular or dendritic microstructure containing several percent of the ductile γ-austenite phase in both as-built and as-built + heat-treated states. A small amount of the Ni3Mo0.5Ti0.5 intermetallic phase was observed even in the as-built state of the material. The heat treatment caused a substantial improvement of the mechanical properties through the homogeneous precipitation of nano-sized needle-shaped Ni3Mo0.5Ti0.5 intermetallic phase. Tensile yield strength increased from 753 to 1957 MPa, ultimate tensile strength—from 991 to 2024 MPa, and microhardness—from 350 to 700 HV0.1. The present results are also compared with those obtained for the same material produced by the more commonly used Laser Powder Bed Fusion (L-PBF) technique. Despite having a coarser microstructure with a presence of γ-phase than the LPBF-printed material, the DED-printed maraging steel exhibited greater precipitation hardening while maintaining 5% ductility after heat treatment.

24 December 2025 in Materials & Design
Verified
Journal Article
Open access
AŠAndrea Školáková
Andrea Školáková
HKHaruka Katayama
Haruka Katayama
PLPavel Lejček
Pavel Lejček
OMOrsolya Molnárová
Orsolya Molnárová
Sadahiro TsurekawaSadahiro Tsurekawa
Sadahiro Tsurekawa
JPJan Pinc
Jan Pinc

14 October 2025 in Journal of Materials Chemistry C
Verified
Journal Article
Open access
PDF file
Irimiciuc Stefan-AndreiIrimiciuc Stefan-Andrei
Irimiciuc Stefan-Andrei
SCSergii Chertopalov
Sergii Chertopalov
VGVeronica Goian
Veronica Goian
EPEsther de Prado
Esther de Prado
MVMartin Vondráček
Martin Vondráček
Jan LancokJan Lancok
Jan Lancok
The controlled growth of highly oriented MnO and Mn 3 O 4 thin films was achieved via kinetics control during pulsed laser deposition. Correlating the growth environment and the properties of the films, generates a context for epitaxial growth.

1 January 2022 in SSRN Electronic Journal
Verified
Preprint
Open access
PDF file
SPSylwia Svorová Pawełkowicz
Sylwia Svorová Pawełkowicz
PSPetr Svora
Petr Svora
ZPZdeněk Prošek
Zdeněk Prošek
MKMartin Keppert
Martin Keppert
EVEva Vejmelková
Eva Vejmelková
HBHana Bíbová
Hana Bíbová
The subject of our work is to develop a photoactive, self-cleaning repair plaster for conservation of various gypsum decorations, such as thin-layer finishing plasters or moulded elements, in compliance with the requirements of the conservators-restorers international community. Hence, the composition of the repair plaster is based on traditional materials (plaster of Paris) with the admixture of modern material – photoactive titanium dioxide (TiO2) in different concentrations 0.5%, 1%, 1.5%, 2%. We present results of mechanical and photoactivity, and microbiological tests together with the phase analysis and study of the microstructure of the mock samples. Several analytical techniques were applied to characterize them, such as X-ray powder diffraction (XRD) and electron microscopy (SEM) coupled with energy dispersive X-ray spectroscopy (EDS). We demonstrate that gypsum/TiO2 conservation plaster could be an effective solution for historical monuments struggling with high air pollution.