5 December 2022 in IEEE Transactions on Power Electronics
Due to its merits of fewer power switches, a wide zero-voltage switching range, and high efficiency, the dual-active-bridge (DAB) microinverter is drawing growing interest. However, it has an inherent issue of grid current distortion and spikes, which deteriorate the total current distortion. Existing literature mainly focuses on modulation strategies and barely analyzes the underlying causes, let alone the methods to improve grid current quality. This article fills this blank by revealing the dead-time effect on grid current distortion from two aspects. Several methods are proposed to improve the grid current quality and are compared in detail. Besides, a complete set of grid current closed-loop control methods is proposed based on the DAB microinverter modeling. The control method not only provides the correct control logic but also eliminates the immanent time-varying and condition-dependent features of the control loop, making the proposed current control method self-adaptive and universal. The analyses and the proposed control method are all validated by experimental results.
17 May 2022 in IEEE Transactions on Industrial Electronics
The cascaded dc–dc converter is a popular topology for large-scale medium-voltage photovoltaic (PV) system with the advantages of high voltage conversion ratio, high efficiency, great flexibility, and independent control capability. However, the absence of optimal string maximum power point tracking (MPPT) operation under power mismatch is a big issue in common centralized control. Furthermore, the cost and time delay are unacceptable resulting from the distance among PV strings in the large-scale PV station and the cascaded dc–dc converter needs to adopt the distributed control method without real-time communication. To this end, by introducing other necessary constraints including voltage constraints, power constraints, and gain constraints on the basis of the distributed MPPT control strategy, a distributed multimode control scheme is proposed in this article. Each submodule (SM) can be switched flexibly between multiple operation modes to maximize the extracted solar energy. Individual string MPPT and autonomous distribution of output voltage are achieved without communication under the proposed distributed control strategy. In this way, optimal operation range is wider, mode switching is simpler, and applicability and robustness are improved. A downscaled prototype and a 35-kV/6-MW simulation system are constructed to verify the effectiveness of the proposed control strategy.
27 June 2023 in IEEE Transactions on Power Electronics
Neutral-point voltage unbalancing is a common problem in three-level inverters. The original neutral-point voltage balancing circuit is the buck-boost converter. Since the inductor carries low frequency components, the power density is limited. At the same time, the efficiency is low because the soft switching cannot be realized. In this paper, a neutral-point voltage balance circuit based on resonant switched-capacitor converter (RSCC) is proposed. The proposed converter uses a series resonant inductor and resonant capacitor to transfer the unbalanced energy between two dc-link capacitors. Based on phase shift modulation, the RSCC circuit controls the output current to compensate the neutral-point current of the inverter to achieve the suppression of neutral-point voltage ripple. To achieve the minimum loss, a step-by-step optimal design is presented and the optimal switching frequency, resonant inductance and resonant capacitance can be derived. The proposed circuit has the advantages that all switches of RSCC can realize the zero voltage switching (ZVS), and the magnetic volume can be greatly reduced because only high frequency components flow through the inductor. A 400V-10A prototype of RSCC and the inverter is built, and main experimental results are provided to verify the time-domain analysis and the effectiveness of the proposed RSCC voltage balance circuit.
1 August 2023 in IEEE Journal of Emerging and Selected Topics in Power Electronics
2 May 2023 in IEEE Journal of Emerging and Selected Topics in Power Electronics
Zero-voltage switching (ZVS) for dual active bridge (DAB) with wide voltage conversion ratio has a contradiction with low conduction loss, especially under light power transmission. Root mean square (RMS) increase of inductor current is unavoidable just by optimizing modulation schemes. Inspired by the various frequency (VF) and various inductor (VI), this article proposes a DAB converter with the capability of regulating the impedance of the resonant tank to extend the ZVS region. With an LC antiresonant circuit in series with original inductor, the equivalent inductance of the resonant network of the proposed converter increases along with the switching frequency within the designed frequency range. Thereby, when the voltage mismatches and the transferred power decreases, a large impedance is obtained by slightly increasing frequency to help to achieve ZVS. Moreover, the proposed DAB is found that single phase shift (SPS) has nearly identical characteristics of ZVS and conduction loss compared with multiple phase shift modulation. The benefit of this is that the complexity of close-loop control is significantly reduced just considering the switching frequency and external shift phase. In addition, ZVS characteristics and optimal control method are analyzed in detail. Finally, a 2 kW 360-400V/40-60V prototype is built, and the main experimental results are provided to verify the feasibility of the proposed converter and soft switching range of all switches.
12 September 2025 in IEEE Transactions on Power Electronics
Single-phase full-bridge inverter operating in triangular current mode (TCM) can realize zero-voltage switching to achieve high efficiency. However, the TCM full-bridge inverter features a wide range of switching frequency variation, especially near the ac current zero-crossing point (ZCP), which increases the switching loss and control difficulty. In this article, an adaptive optimal quasi-trapezoidal current mode (QTCM) control strategy is proposed based on the output characteristics of the full-bridge inverter, which reduces the switching frequency and inductor current rms by adjusting the durations of the different operating modes. The relationship between the zero level ratio m of the inverter output and the switching frequency and the peak inductor current is established. By adjusting the ratio m, co-optimization of switching frequency and conduction loss is implemented according to the output voltage and current. The switching sequence of the power switches is improved to achieve the seamless switching of the ac current ZCP. A 1-kW prototype with Gallium nitride (GaN) devices is built to verify the effectiveness of proposed modulation strategy with a peak efficiency of 98.3%. Compared with TCM, the proposed QTCM has a higher efficiency over the whole load range with the same hardware cost.