Heat dissipation problem is the primary factor restricting the service life of an electronic component. The thermal conductivity of materials has become a bottleneck that hinders the development of the electronic information industry (such as light-emitting diodes, 5G mobile phones). Therefore, the research on improving the thermal conductivity of materials has a very important theoretical value and a practical application value. Whether the thermally conductive filler in polymer composites can form a highly thermal conductive pathway is a key issue at this stage. The carbon fiber/carbon felt (CF/C felt) prepared in the study has a three-dimensional continuous network structure. The nickel-coated carbon fiber/carbon felt (CF/C/Ni felt) was fabricated by an electroplating deposition method. Three-dimensional CF/C/Ni/epoxy composites were manufactured by vacuum-assisted liquid-phase impregnation. By forming connection points between the adjacent carbon fibers, the thermal conduction path inside the felt can be improved so as to improve the thermal conductivity of the CF/C/Ni/epoxy composite. The thermal conductivity of the CF/C/Ni/epoxy composite (in-plane K∥) is up to 2.13 W/(m K) with 14.0 wt % CF/C and 3.70 wt % Ni particles (60 min electroplating deposition). This paper provides a theoretical basis for the development of high thermal conductivity and high-performance composite materials urgently needed in industrial production and high-tech fields.
The formation of highly thermally conductive composites with a three-dimensional (3D) oriented structure has become an important means to solve the heat dissipation problem of electronic components. In this paper, a carbon fiber (CF) felt with a 3D network structure was constructed through the airflow netting forming technology and needle punching. The carbon fiber/phenolic composites were then fabricated by CF felt and phenolic resin through vacuum impregnation and compression molding. The effects of CF felt content and porosity on the thermal conductivity of carbon fiber/phenolic composites were investigated. The enhancement of carbon skeleton content promotes the conduction of heat inside the composites, and the decrease of porosity also significantly improves the thermal conductivity of the composites. The results indicate that the composites exhibit a maximum in-plane thermal conductivity of 1.3 W/mK, which is about 650% that of pure phenolic resin, showing that the construction of 3D thermal network structure is conducive to the reinforcement of thermal conductivity of composites. The method can provide a certain theoretical basis for constructing a thermally conductive composite with a three-dimensional structure.
As electronic devices tend to be integrated and high-powered, thermal conductivity is regarded as the crucial parameter of electronic components, which has become the main factor that limits the operating speed and service lifetime of electronic devices. However, constructing continuous thermal conductive paths for low content particle fillers and reducing interface thermal resistance between fillers and matrix are still two challenging issues for the preparation of thermally conductive composites. In this study, 3D-oriented carbon fiber (CF) thermal network structures filled with boron nitride flakes (BN) as thermal conductive bridges were successfully constructed. The epoxy composite was fabricated by thermal conductive material with a 3D oriented structure by the vacuum liquid impregnation method. This special 3D-oriented structure modified by BN (BN/CF) could efficiently broaden the heat conduction pathway and connected adjacent fibers, which leads to the reduction of thermal resistance. The thermal conductivity of the boron nitride/carbon fiber/epoxy resin composite (BN/CF/EP) with 5 vol% 10 mm CF and 40 vol% BN reaches up to 3.1 W m−1 K−1, and its conductivity is only 2.5 × 10−4 S cm−1. This facile and high-efficient method could provide some useful advice for the thermal management material in the microelectronic field and aerospace industry.
The low thermal conductivity and poor shape stability of phase change materials (PCMs) have seriously restricted their applications in energy storage and energy saving. In this paper, poly(ethylene glycol)–calcium chloride/carbon/carbon fiber felt (PEG-CaCl2/CCF) PCMs were fabricated by a liquid-phase impregnation–vacuum drying–hot compression molding method with carbon/carbon fiber felt as the three-dimensional (3D) thermal skeleton and PEG-CaCl2 as the polymer PCM matrix. PCMs were heated and compressed by the compression confinement method to improve the contact area between 3D skeleton carbon fibers. The carbon fibers in PCMs presented a 3D (X–Y–Z) network structure and the fiber arrangement was anisotropic, which were beneficial to improve the thermal conductivity of PCMs in the fiber direction. The compression confinement can improve the contact area between the fibers in the 3D skeleton. As a result, the thermal conductivity of PEG-CaCl2/CCF PCMs can reach 3.35 W/(m K) (in-plane) and 1.94 W/(m K) (through-plane), about 985 and 571% of that of PEG-CaCl2, respectively. Due to the complexation of PEG and CaCl2 and the 3D skeleton support of carbon fiber felt, PCMs have excellent shape stability. The paper may provide some suggestions for the preparation of high thermal conductivity and excellent shape stability PCMs.