In this work, we demonstrate that the permeability of 1 μm thick NiFe/Cr multilayer films can be tuned by varying the thickness of individual NiFe layers while keeping the total multilayer film thickness constant. Our results show that the permeability can be increased from 170 to 650 by varying the NiFe thicknesses from 100 to 50 nm. The thickness dependant permeability variation was attributed to the presence of stripe domains, as examined by hysteresis measurements and magnetic force microscope imaging. Films with thinner NiFe layers coupled with on-chip spiral inductors enable an inductance increase by a factor of 6.
This work uniquely reports the synthesis of ZnxMg1–xO nanowires and submicron columns by utilizing a traditional carbothermal reduction process toward forming ZnO nanowire ultraviolet detectors, while simultaneously utilizing Mg3N2 as the source of Mg. To investigate the relationship between Mg content in the ZnO lattice and the cutoff wavelength for high spectral responsivity, the nanowires were annealed in a series of designed conditions, whereas chemical, nanostructural, and optoelectronic characteristics were compared before and after treatment. Postanneal scanning electron micrographs revealed a reduction of the average ensemble nanowire dimensions, which was correlated to the modification of ZnO lattice parameters stemming from Zn2+ dissociation and Mg2+ substitution (confirmed via Raman spectroscopy). The analysis of cathodoluminescence spectra revealed a blueshift of the peak alloy band-edge emission along with a redshift of the ZnO band-edge emission; and both were found to be strong functions of the annealing temperature. The conversion of Zn2SiO4 to Mg2SiO4 (in O2) and MgSiO3 (in Ar) was found to correspond to transformations (shifting and scaling) of high-energy luminescence peaks and was confirmed with X-ray diffraction analysis. The tunability of the cutoff photodetection wavelength was evaluated as the nanowire arrays exhibited selective absorption by retaining elevated conduction under high-energy UV-C irradiation after thermal treatment but exhibiting suppressed conductivity and a single order of magnitude reduction in both spectral responsivity (Rλ) and photoconductive gain (G) under UV-A illumination. Noise analysis revealed that the variation of detectivity (D*) depended on the regime of ultraviolet irradiation, and that these variations are related to thermal noise resulting from oxygen-related defects on both nanowire and substrate surfaces. These results suggest a minor design tradeoff between the noise characteristics of thermally treated ZnMgO nanowire array UV detectors and the tunability of their spectral sensitivity.
2 July 2018 in IEEE Transactions on Electron Devices
Autonomous smart windows may be integrated with a stack of active components, such as electrochromic devices, to modulate the opacity/transparency by an applied voltage. This voltage may be generated with a visibly transparent photovoltaic device. This paper describes the processing and performance of zinc oxide (ZnO) films for integration with electrochromic stacks. Sputtered ZnO (2% Mn) films on indium-tin oxide with transparency in the visible range were used to fabricate metal- semiconductor (MS), metal-insulator-semiconductor, and p-i-n heterojunction devices, and their photovoltaic conversion under ultraviolet (UV) illumination was evaluated with and without oxygen plasma-treated surface electrodes (Au, Ag, Al, and Ti/Ag). The MS Schottky parameters were fit against the generalized Bardeen model to obtain the density of interface states (D it ≈ 8.0 × 10 11 eV -1 cm -2 ) and neutral level (E o ≈ -5.2 eV). These devices have exhibited a photoconductive behavior at λ = 365 nm, and low-noise Ag-ZnO detectors have exhibited the responsivity (R) and photoconductivegain (G) of 1.93×10 -4 A/W and 6.57×10 -4 , respectively. Confirmed via matched-pair analysis, postmetallization oxygen plasma treatment of Ag and Ti/Ag electrodes has resulted in increased Schottky barrier heights, which maximized with a 2-nm SiO 2 electron blocking layer, coupled with the suppression of recombination at the MS interface and blocking of majority carriers. For interdigitated devices under monochromatic UV-C illumination, the open-circuit voltage (V oc ) was 1.2 V and short-circuit current density (J sc ), due to minority carrier tunneling, was 0.68 mA/cm 2 .
This paper presents integrated inductors with Co-Zr-Ta-B (CZTB) thin films on flexible organic substrates for MHz-GHz applications. This paper demonstrated the fabrication and characterization of magnetic thin-film inductors on flexible organic substrates, such as polyimide and Ajinomoto build-up film thin films. These films have thicknesses of only tens of micrometer and thus are very flexible compared to the same inductor structures fabricated on rigid substrates, such as quartz. The magnetic films on flexible substrates were observed to maintain similar magnetic properties compared with those on Si substrate, but with greater coercivity likely due to the increased roughness of the substrate surface. The fabricated thin-film inductors on organic substrates with inductance L, measured by RF characteristics, have shown significantly increased inductance compared to air-core inductors (without magnetic core materials). This paper also demonstrated a high frequency response, clearly over GHz, consistent with the CZTB type of materials. The frequency response, as well as inductance and Q values, remains similar even after many iterations of bending to a large degree, indicating the robustness of the inductor on flexible organic substrates, as well as that of the magnetic thin films.
4-[(4-Cyanophenyl)acetylenyl]-2,3,5,6-tetrafluorophenyl 4-n-alkoxybenzoates, which contain a perfluorinated phenyl ring in their aromatic core system, exhibit nematic phases with a wide thermal range. In comparison with the homologues without fluorine, the introduction of the perfluorinated phenyl ring leads to the formation of a nematic phase and reduces the melting and clearing points.