Printed and flexible sensors are in the focus of recent efforts to establish the advantages of low-cost manufacturing techniques such as screen printing or inkjet printing for printed electronical applications. Devices based on conductive carbon nanotube (CNT) networks within polymeric matrices such as polydimethylsiloxane (PDMS) are already exceeding mere technological demonstrations. Therefore, we investigate the application-oriented behaviour of fully inkjet-printed CNT/PDMS strain sensors under different conditions such as short- and long-term performance. The sensors exhibit a quasi-linear piezoresistive behaviour with vanishing hysteresis to tensile strain. Significant differences in the resistive response between compressive and tensile strain suggest complex re-orientation mechanisms of CNTs inside the matrix. No clear indication for this phenomenon could be observed in the evolution of the CNT network resistance during fatigue measurements within an uncured or cured PDMS matrix, where both scenarios exhibit no visual degradation. However, these measurements over thousands of cycles show different permanent changes in the overall device resistance exhibiting damages but also recovery in the network. Considering these findings facilitates the development of printed sensor devices.
5 October 2022 in Flexible and Printed Electronics
Printable and flexible memory devices have attracted a great deal of attention in several emerging technological applications for the development of flexible electronics, such as interconnections/wearables/smart devices for the internet of things (IoT). In this work, we report on the fabrication of flexible, transparent, and fully inkjet-printed resistive random access memory (ReRAM) cells using poly(3,4-ethylenedioxythiophene):polystyrene sulfonate (PEDOT:PSS)/ZnO/PEDOT:PSS structures. The electrical characteristics were studied, including the determination of space charge limited conduction (SCLC) as the dominant charge transport mechanism. In addition, the bending performance and the transparency of the devices was tested in order to confirm the reliable operation and reproducibility of the cells. The switching for the printed structures of PEDOT:PSS/ZnO/PEDOT:PSS was led through the formation and dissolution of a stable oxygen vacancy filament, as confirmed by conductive atomic force microscopy. While the conduction mechanism for the high resistance state (HRS) was attributed to the SCLC mechanism. The switching of the memory cells, their endurance and retention properties were analysed and indicated the stability of the HRS and low resistance state for more than 104 cycles and 105 s comparable to ZnO-based ReRAM produced by clean-room techniques. The study of the mechanical flexibility of the cells shows that up to 700 bending cycles can be reached without significantly changing the switching characteristics.
1 September 2021 in Flexible and Printed Electronics
With the rapid proliferation of consumer electronics in our day to day lives, there is an ever increasing demand for flexible electronic devices which are low cost, easy to fabricate and deliver reliable performance. In this work, we report fabrication of symmetric poly(3,4-ethylenedioxythiophene):polystyrene sulfonate (PEDOT:PSS)/WO 3 /PEDOT:PSS memory cells by inkjet printing on transparent, flexible polyethylene naphthalate (PEN) substrates. The cells show resistive switching behavior with two stable resistance states. The current conduction across the interface between the PEDOT:PSS electrode and dielectric WO 3 is determined by localized filamentary features which is space charge limited in the high resistance state, facilitated through the migration of oxygen vacancies at low voltages (2 V). The cells show good retentivity and endurance (>6000 cycles). The cells are entirely sinter free and no electroforming is required to activate them. These characteristics make them suitable for the next generation of flexible non-volatile memory devices.
Printed electronics require a multitude of various inks for different applications which leads to compatibility issues for their integration. We present a procedure to deposit a thin layer of Cu x S via inkjet printing of Na 2 S on a thermally grown or inkjet-printed Cu surface that provides applications in electrochemical metallization memory cells (ECMs) or temperature sensors. The nanosized transformation from Cu to Cu x S is investigated via confocal microscopy, scanning electron microscopy (SEM), as well as energy-dispersive x-ray spectroscopy (EDX). We analyze individual responses from the sensor and memory and evaluate their respective potential in printed electronics. The negative temperature coefficient of the semiconducting Cu x S is determined to be K. Resistive switching is observed for a current compliance between 0.1 and 1000 µ A, with a resistance ratio R /R up to 10 5 . The use of the same inks and processes for the memory and sensor components paves the way for new and customized designs for smart logistics applications where temperature monitoring is required.