Na-Hee Chang

Na-Hee Chang

Auto-generated profile, based on publicly available information

Na-Hee Chang

Biomedical Research Institute, Seoul National University Bundang Hospital, Seongnam 13620, Korea

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
4 February 2018 in Materials
Verified
Journal Article
Open access
PDF file
SPSu A. Park
Su A. Park
HLHyo-Jung Lee
Hyo-Jung Lee
KKKeun-Suh Kim
Keun-Suh Kim
SLSang Jin Lee
Sang Jin Lee
JLJung-Tae Lee
Jung-Tae Lee
SPShin-Young Park
Shin-Young Park
Insufficient bone volume is one of the major challenges encountered by dentists after dental implant placement. This study aimed to evaluate the efficacy of a customized three-dimensional polycaprolactone (3D PCL) scaffold implant fabricated with a 3D bio-printing system to facilitate rapid alveolar bone regeneration. Saddle-type bone defects were surgically created on the healed site after extracting premolars from the mandibles of four beagle dogs. The defects were radiologically examined using computed tomography for designing a customized 3D PCL scaffold block to fit the defect site. After fabricating 3D PCL scaffolds using rapid prototyping, the scaffolds were implanted into the alveolar bone defects along with β-tricalcium phosphate powder. In vivo analysis showed that the PCL blocks maintained the physical space and bone conductivity around the defects. In addition, no inflammatory infiltrates were observed around the scaffolds. However, new bone formation occurred adjacent to the scaffolds, rather than directly in contact with them. More new bone was observed around PCL blocks with 400/1200 lattices than around blocks with 400/400 lattices, but the difference was not significant. These results indicated the potential of 3D-printed porous PCL scaffolds to promote alveolar bone regeneration for defect healing in dentistry.

7 July 2020 in Applied Sciences
Verified
Journal Article
Open access
PDF file
IUInwoong Um
Inwoong Um
Jeong-Kui KuJeong-Kui Ku
Jeong-Kui Ku
YKYu-Mi Kim
Yu-Mi Kim
Pil-Young YunPil-Young Yun
Pil-Young Yun
NCNa-Hee Chang
Na-Hee Chang
YCYong-Hoon Choi
Yong-Hoon Choi
Autogenous and allogeneic demineralized dentin matrices (Auto-DDM and Allo-DDM, respectively) are currently used for guided bone regeneration (GBR). Buccal marginal bone (BMB) resorption is critical for successful implant integration. This study analyzed BMB resorption around dental implants for GBR between the control group (Auto-DDM graft) and experimental group (Allo-DDM graft). From 2014 to 2019, we enrolled 96 patients (59 males, 37 females, average 57.13 years) who received GBR (52 and 44 using Allo-DDM and Auto-DDM, respectively,) without a barrier membrane and a simultaneous single dental implantation (54 in the maxilla and 42 in the mandible). BMB height was measured immediately after GBR, at prosthetic loading, and 12 months after loading. BMB resorption was classified as initial resorption (between GBR and prosthetic loading) and functional resorption (during 12 months after prosthetic loading). The differences in the BMB levels of Auto-DDM and Allo-DDM were analyzed between the initial and functional resorption stages by independent sample t-test. Auto-DDM and Allo-DDM showed similar BMB changes in initial resorption (0.73 ± 0.97 and 0.72 ± 0.77 mm, respectively) and functional resorption (0.69 ± 0.81 and 0.48 ± 0.58 mm, respectively) without a significant difference between the maxilla and mandible. For GBR, Allo-DDM is comparable to Auto-DDM in terms of BMB resorption.