Chao Li

Chao Li

Auto-generated profile, based on publicly available information

Chao Li

Faculty of Electrical and Control Engineering, Liaoning Technical University, Huludao, China

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
14 February 2023 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
HLHongzhu Li
Hongzhu Li
CLChao Li
Chao Li
XSXuanjin Sun
Xuanjin Sun
LCLihong Cheng
Lihong Cheng
WLWenrui Li
Wenrui Li
This article proposes an interleaved high step-up converter based on three-winding coupled inductor (TW-CI) with symmetrical structure. By utilizing the TW-CI along with a voltage multiplier cell, the proposed converter achieves high power transfer ability as well as minimized voltage stress across power switches and diodes. The converter has significantly improved the voltage gain by integrating two TW-CIs with the passive clamp circuit. The leakage inductor energy of the TW-CI is recycled to improve the voltage gain and efficiency while facilitating the soft switching condition for the power switches. Additionally, the voltage stress across the power switches is decreased with the help of the clamping capacitors. Therefore, low-voltage-rated semiconductors with small on-resistance can be chosen which reduce conduction losses and improve the overall performance. Moreover, two series-connected capacitors of the primary side are introduced, which effectively balance the voltage between the power switches and the capacitors during steady and dynamic states. Finally, a 400 W experimental prototype with 24–400 V is built to verify the accuracy of the proposed converter.

20 June 2023 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
CLChao Li
Chao Li
HLHongzhu Li
Hongzhu Li
NWNing Wang
Ning Wang
XSXuanjin Sun
Xuanjin Sun
LCLihong Cheng
Lihong Cheng
This paper proposes a full soft-switching high step-up DC/DC converter with active-switched-inductor and three-winding coupled inductor (ASL-TWCI). By utilizing the three-winding coupled inductor (TWCI) with a modified switched capacitor cell, the voltage gain of the ASL-TWCI is further extended without requiring an extreme duty or a high turns-ratio of TWCI. Therefore, the voltage stress across the power switches is restricted. By utilizing the leakage energy of TWCI, all semiconductors achieve the Zero Current Switching (ZCS) performance, which has significantly reduced the switching losses of the ASL-TWCI. Additionally, the soft-switching performance is realized by utilizing few components, which reduces the losses and improves overall efficiency. Moreover, the construction of capacitor clamped cell has been adjusted to decrease capacitance and voltage rating, which significantly improve the power density of ASL-TWCI. The operating principles, steady-state analysis, design, and extensive performance comparison of ASL-TWCI are described in detail. Finally, a 400W prototype with 400V output voltage is fabricated to verify the theoretical analysis.

10 January 2025 in IEEE Transactions on Transportation Electrification
Verified
Journal Article
Closed access
HLHongzhu Li
Hongzhu Li
CLChao Li
Chao Li
XSXuanjin Sun
Xuanjin Sun
WLWenjing Li
Wenjing Li
ZYZhen Yang
Zhen Yang
Dual-input DC-DC converters are increasingly recognized as integrated systems for various applications, such as electric vehicle charging station and distributed energy systems, due to the compact size and cost-effectiveness. Therefore, a novel dual-input single-output high step-up DC-DC converter with three-winding coupled inductor (DISO-TWCI), which secondary and tertiary windings are integrated with switched capacitor, is proposed to achieve a high voltage conversion ratio without an extremely duty cycle. And the diode-capacitor clamp circuit is utilized to minimize the voltage spikes across switches, which is beneficial for selecting switches with low voltage ratings. Moreover, the switches can achieve the Zero Current Switching (ZCS) with the help of leakage inductor from TWCI. By integrating the passive clamp network, the number of components in DISO-TWCI can be reduced, significantly enhancing its performance. The operating principles, steady-state analysis, design and performance analysis of DISO-TWCI are described in detail. Finally, the theoretical correctness is verified by building an experimental prototype with switching frequency of 100 kHz. The rated power is 400 W with 24-24V input and 400V output.

29 May 2023 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
CLChao Li
Chao Li
HLHongzhu Li
Hongzhu Li
LCLihong Cheng
Lihong Cheng
XSXuanjin Sun
Xuanjin Sun
NWNing Wang
Ning Wang
WLWenjing Li
Wenjing Li
This article proposes a novel nonisolated dual-input single-output high step-up dc/dc converter with coupled inductor (NI-DISO-CI) for the distributed sources. The coupled inductor along with the passive clamp circuits is employed to the NI-DISO-CI, which can achieve the high voltage conversion ratio without operating at an extremely duty cycle. The energy stored in leakage inductor is recycled by the passive clamp circuits, which can minimize the voltage spikes across power switches. Therefore, the power switches with low parasitic parameters can be selected. The power switches can achieve the zero current switching performance by utilizing the leakage inductor from coupled inductor. The operating principle, steady-state analysis, design and performance of the NI-DISO-CI are described in detail. Finally, the experimental prototype with the switching frequency of 100 kHz and the power rating of 400 W is built to verify the accuracy of the theoretical analysis.

17 February 2025 in IEEE Transactions on Industrial Electronics
Verified
Journal Article
Closed access
XSXuanjin Sun
Xuanjin Sun
DRDesheng Rong
Desheng Rong
CLChao Li
Chao Li
A high step-up Cuk-Boost converter based on coupled inductors for renewable energy systems has been proposed in this article. Higher voltage gains and continuous input and output ports currents are achieved by utilizing topology integration technique and coupled inductor multiplier technique. The low current ripple in the input side is employed by driving the two switches in an interleaved manner. The energy generated by the leakage inductance is absorbed by the passive clamp circuit, which reduces the voltage spike of the switches. The current sharing between the two switches is achieved. In addition, the zero-current switching (ZCS) of the switches is achieved and the reverse recovery problem of the diodes is alleviated. The operation principles and performance of the proposed converter are analyzed in detail at full duty cycle range. Meanwhile, the current equalization design and the design reference of the components are given. Finally, a 400 W, 28–42 V input, 400 V output experimental prototype is built to verify the theoretical analysis.

23 October 2025 in IEEE Transactions on Industrial Electronics
Verified
Journal Article
Closed access
CLChao Li
Chao Li
HLHongzhu Li
Hongzhu Li
XSXuanjin Sun
Xuanjin Sun
This article proposes a high step-up quadratic dc–dc converter-based Y-source coupled inductor (YSCI) with quasi-resonance operation, which integrates a modified quadratic Boost-Sepic converter, switched capacitor, and YSCI to achieve high voltage gain with reduced voltage stress across semiconductors. The leakage inductor of YSCI limits the current change rate, achieving zero current switching (ZCS) turn-on for the switches and mitigating reverse recovery of diodes. Simultaneously, it facilitates quasi-resonant operation, which contributes to ZCS turn-off for diodes. Moreover, the switched capacitor is integrated with passive clamped circuit to reduce the voltage rating across the output capacitor. Additionally, the leakage energy stored in the leakage inductor is absorbed by the switched capacitor, thereby limiting voltage spikes across the semiconductors. The input inductors of modified quadratic Boost-Sepic converter ensure the continuous input current. The operation principles, steady-state analysis, and design considerations of the proposed converter are detailed. Finally, the theoretical analysis is validated through the construction of a 400 W experimental prototype with input and output voltages of 24 and 400 V, respectively.