6 October 2023 in IEEE Access
This paper proposes a single-switch integrated Sepic converter with a Y-source coupled inductor. The three-winding coupled inductor has higher voltage regulation efficiency, and the three-port tap of the y-source is easier to integrate with other structures to form a composite power cell. While ensuring the continuous input current, it can flexibly adjust the voltage gain, increase the power capacity, and reduce the voltage stress of the switch. The diode-capacitor branch in the integrated topology is used as a clamp to suppress the voltage shock while using the absorbed leakage energy to achieve soft-switching characteristics, mitígate diode reverse recovery, and improve the efficiency of the converter. The converter can be applied to the output of the photovoltaic (PV) array, a detailed theoretical analysis of the converter is carried out, and the general extension of the topology and the extension of the converter family are given. Finally, a 150 W prototype was built to verify that the converter can achieve high gain under high efficiency.
14 August 2023 in IEEE Transactions on Industrial Electronics
An interleaved high step-up boost-zeta converter with resonant coupled inductors voltage multiplier cell is proposed in this article. The proposed converter achieves very high voltage gain by integrating the boost converter and the zeta converter and using coupled inductor voltage multiplier technique. Meanwhile, low input current ripple and continuous output current are realized, which is beneficial for photovoltaic, fuel cell, and dc-bus. Moreover, the zero-voltage switching (ZVS) and low voltage stress of the switches are achieved by utilizing the active clamp circuits. With the resonance between the leakage inductance and the resonant capacitor in the resonant coupled inductor multiplier cell, the zero-current switching (ZCS) of the diodes are achieved, leading to low reverse recovery losses. In addition, the main switches of the proposed converter can be operated in the full duty cycle range, which achieves a wide range of step-up regulation. The operation principles and steady-state performance of the proposed converter are analyzed in detail. A 400 W prototype with 30–40 V input, 400 V output is built to verify the theoretical analysis.
20 May 2024 in IEEE Access
Aiming at the application scenario of high voltage transmission rate in distributed power generation systems, this paper proposes a novel high-boost DC-DC converter. The overall design of the converter combines the improved secondary active switching inductor with the coupled inductor. Adoption of staggered conduction, which in turn reduces input current ripple. The voltage gain is further improved by integrating the coupled inductor voltage doubling unit. The passive clamp circuit is used to absorb and utilize the leakage energy of the coupled inductor, which greatly reduces the voltage spike of the switch. In this paper, the working principle and steady-state performance of the converter are analyzed in detail, and the superiority of the proposed converter is proved by the performance comparison between the converters. Finally, a 200W experimental prototype was built for verification, which used common components and measured a maximum efficiency of 92.2%. The experimental results verify the correctness of the theoretical analysis and the feasibility of the proposed converter topology.
27 February 2023 in IEEE Journal of Emerging and Selected Topics in Power Electronics
This paper proposes a high-gain Buck-Boost-Zeta converter with three-winding coupled inductor, which is generated by differentially connecting the Buck-Boost converter and the Zeta converter and integrating the coupled inductor multiplier cell. An active switched-inductor is obtained at the input side by differential connection, which is used as the primary winding of the three-winding coupled inductor, and the multiplier cell is composed of the secondary winding and diode-capacitor. The diode-capacitor circuit in the topology is multiplexed as a passive clamp branch to absorb the leakage energy and the ZCS turn-on of the switches is achieved. Therefore, the proposed converter achieves higher voltage gain and lower switch voltage stress. At the same time, the proposed converter retains the continuous output current characteristic of the Zeta converter. The operation principles and performances of the proposed converter are analyzed in detail. Meanwhile, the imbalance currents of the primary windings caused by the leakage inductance error is analyzed and the coupled inductor current sharing method is given, which effectively alleviates the current pulsation of the primary winding. A 400W experimental prototype is built to verify the theoretical analysis.
11 April 2025 in IEEE Journal of Emerging and Selected Topics in Power Electronics
This article proposes a high step-up soft-switching integrated Boost-Sepic converter with a Y-source coupled inductor for interface circuit of renewable energy power generation systems. By combining the Boost converter, Sepic converter, and Y-source coupled inductor, the converter achieves a higher voltage gain. Additionally, it features low input current ripple and a common ground for both the input and output. A series of multiple switched capacitor units can be cascaded on the output side of the converter, allowing for enhanced flexibility and expandability. The output voltage is shared by three capacitors, which effectively reduces the voltage stress on the capacitors and reduces the size of the capacitors. In addition, the active clamping circuit effectively utilizes the leakage inductance energy, enabling zero-voltage switching (ZVS) for the switch and zero-current switching (ZCS) for the diode, thereby reducing the loss of the switching elements. Since the switch is positioned before the Y-source, the switch also has lower voltage stress and operates over the full duty cycle range. This article presents a detailed analysis of the operating principle and steady-state performance of the converter. A 400W experimental prototype was constructed to validate the correctness and feasibility of the theoretical analysis.
17 February 2025 in IEEE Transactions on Industrial Electronics
A high step-up Cuk-Boost converter based on coupled inductors for renewable energy systems has been proposed in this article. Higher voltage gains and continuous input and output ports currents are achieved by utilizing topology integration technique and coupled inductor multiplier technique. The low current ripple in the input side is employed by driving the two switches in an interleaved manner. The energy generated by the leakage inductance is absorbed by the passive clamp circuit, which reduces the voltage spike of the switches. The current sharing between the two switches is achieved. In addition, the zero-current switching (ZCS) of the switches is achieved and the reverse recovery problem of the diodes is alleviated. The operation principles and performance of the proposed converter are analyzed in detail at full duty cycle range. Meanwhile, the current equalization design and the design reference of the components are given. Finally, a 400 W, 28–42 V input, 400 V output experimental prototype is built to verify the theoretical analysis.