Basheer Sheeba Jinshah

Basheer Sheeba Jinshah

Auto-generated profile, based on publicly available information

Basheer Sheeba Jinshah

National Institute of Technology Tiruchirappalli

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
26 September 2018 in International Journal of Green Energy
Verified
Journal Article
Closed access
JKJinshah B. S. Kalluvila
Jinshah B. S. Kalluvila
BSB. Sreejith
B. Sreejith
Presently Horizontal Axis Wind Turbines are used extensively for generation of electricity from wind. These turbines are not preferred in regions where the wind speed is low and/or wind direction changes continuously. Also, these turbines are not suitable for urban areas where wind turbulence is high and land availability is low. The Savonius wind turbine is a drag-driven Vertical Axis Wind Turbine, which is simple in design and easy to fabricate. Savonius wind turbines have much lower efficiency compared with other lift- driven wind turbines. The present study focuses on increasing the efficiency of Savonius rotor by considering some modifications in the conventional profile of it and placing guide blades around it. Computational Fluid Dynamic (CFD) analysis was conducted for selecting guide blades and predicting the performance of the turbine. An experimental study was conducted with the turbine having proposed modifications, and the results of CFD analysis were validated. The maximum power coefficient obtained from the study is 28%. It was established from the study that guide vanes help to reduce negative torque resulting in increased efficiency. Turbines with proposed modifications can be used even in regions where wind speed is low and turbulence is high.

28 June 2022 in International Journal of Energy Research
Verified
Journal Article
Closed access
KBKaruppudayar Ramaraj Balasubramanian
Karuppudayar Ramaraj Balasubramanian
RKRavi Kumar Kottala
Ravi Kumar Kottala
SPSakthivel Puvaneswaran Sathiya Prabhakaran
Sakthivel Puvaneswaran Sathiya Prabhakaran
BJBasheer Sheeba Jinshah
Basheer Sheeba Jinshah
NANalluri Abhishek
Nalluri Abhishek

25 February 2022 in Energy Sources, Part A: Recovery, Utilization, and Environmental Effects
Verified
Journal Article
Closed access
RKRavi Kumar Kottala
Ravi Kumar Kottala
BRBalasubramanian Karuppudayar Ramaraj
Balasubramanian Karuppudayar Ramaraj
JSJinshah B S
Jinshah B S
MVMuthya Goud Vempally
Muthya Goud Vempally
MLMaheswari Lakshmanan
Maheswari Lakshmanan
The main objective of this present research work is to investigate the feasibility of LiNO3 + NaCl/expanded graphite (EG) composite phase change material for medium-temperature thermal energy storage systems. EG was used as supporting material to enhance the eutectic PCM samples thermal conductivity. The XRD, FTIR and SEM results reveal that EG particles are uniformly dispersed to the PCM material and show better chemical stability. The phase transition temperature and latent heat values of pure eutectic PCM and composite eutectic PCMs are experimentally measured with the help of differential scanning calorimetry (DSC). The calculated thermal conductivity intensification of composite PCM with 9% EG composition is 5.75, significantly more than pure PCM salt. The composite PCM showed good thermal reliability performance even after 500 thermal cycles. The charging time of the PCM significantly decreases with EG loading. The corrosion rate of five metal specimens is determined when embedded in pure PCM and composite PCM samples at more than phase transition temperature for 1440 h. The metal specimens embedded in composite PCM show good corrosion stability. Among all the selected metal specimens, stainless steel 316 L showed better corrosion resistivity in both PCM samples. Furthermore, an artificial neural network model is developed to predict the DSC output parameters such as temperature and heat flow at various EG loading (%), heating rate, and conversion points.


16 June 2021 in Energy Sources, Part A: Recovery, Utilization, and Environmental Effects
Verified
Journal Article
Closed access
JSJinshah B S
Jinshah B S
BRBalasubramanian Karuppudayar Ramaraj
Balasubramanian Karuppudayar Ramaraj
RKRavi Kumar Kottala
Ravi Kumar Kottala
SPSivapirakasam S P
Sivapirakasam S P
Phase change material (PCM) that is used in the roof top slab can minimize the heat infiltration into the living space from the building envelope and increase the indoor thermal comfort level. The major disadvantage of PCM is leakage at liquid state. Expanded graphite (EG) is used here as supporting material for PCM to prevent the leakage and maintains the form stability. The composite PCMs are prepared by adding the EG with various mass ratios, i.e. 3%, 6%, and 9%. The thermal properties of all composite PCMs are determined by DSC and thermal conductivity analyzer. The optimum PCM composition was found at 9% of EG. In this study, the shape-stabilized PCM-integrated roof top was analyzed by simplified temperature transforming (TT) numerical model. The main advantage of this model is that it is used to combine the equivalent enthalpy and heat capacity. The numerical results are validated with experimental values and show the lower mean absolute percentage error (MAPE), i.e. 6.91%. This indicates that present model is well suitable to predict the thermal performance of composite PCM incorporated roof top. The effect of various parameters like thickness of the PCM slab, wind velocity, percentage of EG mass ratio, and location of PCM are investigated by simplified TT model. The results showed that the maximum inner surface temperature reach up to 53°C for BG model (concrete and gypsum) by distributing constant heat flux, i.e. 1,000 W/m2 for 180 min. At this same condition, the inner surface temperature of other PCM models PBG (PCM, concrete, gypsum) and BPG (concreate, PCM, Gypsum) reaches to 50°C and 41°C, respectively. PBG model exhibits excellent thermal performance compared to BPG model. The thermal performance of PCM slab is also investigated by varying the thickness of the PCM layer and found that time lag is raised with the thickness of the PCM slab.

1 October 2023 in International Journal on Interactive Design and Manufacturing (IJIDeM)
Verified
Journal Article
Closed access
PDF file
DSDivakar Senthilvel
Divakar Senthilvel
KBK. R. Balasubramanian
K. R. Balasubramanian
BJB. S. Jinshah
B. S. Jinshah