Institute of Sustainability for Chemicals, Energy and Environment, Agency for Science, Technology and Research (A*STAR), 1 Pesek Road, Jurong Island, Singapore 627833, Singapore
Auto-generated profile, based on publicly available information
Febin Cyriac
Institute of Sustainability for Chemicals, Energy and Environment, Agency for Science, Technology and Research (A*STAR), 1 Pesek Road, Jurong Island, Singapore 627833, Singapore
The influence of structural factors on the lubrication performance of organic friction modifiers (OFMs) formulated in Group V (polyol ester oil) base oil was studied using a ball-on-disk tribometer. The results show that OFMs can mitigate friction under heavy loads, low sliding speeds, and high temperatures. These conditions are commonly encountered in internal-combustion engines between cylinder liners and piston rings. The reduction in friction is ascribed to the boundary lubrication film containing the OFM. The chemical composition analysis of the metal disk surface using energy dispersive X-ray spectroscopy (EDS) confirmed the presence of a protective film of OFM on the wear track, albeit inconsistently deposited. Although the adsorption of the OFM on the metal surface was observed to be dependent on the chemical reactivity of the functional groups, levels of unsaturation, and hydrocarbon chain length of the OFM, the frictional performance was not always directly correlated with the surface coverage and tribofilm thickness. This implies that the friction reduction mechanism can involve other localized processes at the interface between the metal surface and lubricant oil. The occasional variation in friction observed for these OFMs can be attributed to the stability and durability of the boundary film formed during the rubbing phase.
The manufacturing process for ointments typically involves a series of heating, cooling, and mixing steps. Precise control of the level of mixing through homogenization and the cooling rate, as well as temperature at different stages, is important in delivering ointments with the desired quality attributes, stability, and performance. In this work, we investigated the influence of typical plant processing conditions on the microstructure, stability, and sensorial properties of a model ointment system through a Design of Experiments (DoE) approach. Homogenization speed at the cooling stage after the addition of the solvent (propylene glycol, PG) was found to be the critical processing parameter that affects stability and the rheological and sensorial properties of the ointment. A lower PG addition temperature was also found to be beneficial. The stabilization of the ointment at a lower PG addition temperature was hypothesized to be due to more effective encapsulation by crystallizing mono- and diglycerides at the lower temperature. The in vitro release profiles were found to be not influenced by the processing parameters, suggesting that for the ointment platform studied, processing affects the microstructure, but the effects do not translate into the release profile, a key performance indicator. Our systematic study represents a Quality-by-Design (QbD) approach to the design of a robust manufacturing process for delivering stable ointments with the desired performance attributes and properties.
The aim of the work was to identify the physical parameters relevant to different perceptual attributes by comparing a range of commercial skin creams with various compositions. We investigated the possibility of predicting sensory properties using rheological and tribological methods. Rheological evaluations of the skin creams were carried out using continuous shear, creep, creep recovery, rheodestruction and recovery measurements, oscillatory strain sweep measurements [small amplitude oscillatory shear (SAOS) and large amplitude oscillatory shear (LAOS)], and frequency sweep measurements. Friction measurements were performed on the nonbiological skin model to investigate how surface properties are influenced by the application of different topical formulations. Furthermore, the formulations were characterized by a broad range of instrumental texture measurements. In vivo sensory analysis based on the spectrum descriptive analysis method was performed to discriminate the skin creams during pickup, rub out, and after feel. Using principal component analysis meaningful correlation relating rheotribological properties and sensory attributes during the entire process of product application was carried out. Rheological parameters deduced from the nonlinear regime were found to be important parameters affecting the frictional response of skin creams. In addition, friction data were correlated with slipperiness and stickiness—subjective attributes used for the sensory evaluation of after feel. Furthermore, a number of key textural parameters and sensorial data showed good correlation with results obtained from linear and nonlinear rheological measurement, indicating rheological analysis can be sufficiently used as a precise and valid tool for sensorial mapping of topical formulations. Our study further suggests that objective evaluation based on the flow curve, oscillatory strain sweep (SAOS and LAOS), and friction measurements can be used for sensorial screening of large number of prototype formulations, which otherwise may be time consuming and costly using a sensory panel.
A classical emulsion formulation based on petrolatum and mineral oil as the internal phase with emulsifier wax as a typical topical emulsion cream was investigated for the effect of process parameters on drug product quality and performance attributes. The Initial Design of Experiment (DoE) suggested that an oil phase above 15%, coupled with less than 10% emulsifying wax, resulted in less stable emulsions. Different processing parameters such as homogenization speed, duration, cooling rate, and final temperature showed minimal influence on properties and failed to improve stability. The final DoE suggested that the optimal emulsion stability was achieved by introducing a holding period midway through the cooling stage after solvent addition. Within the studied holding temperature range (25–35 °C), a higher holding temperature correlated with increased emulsion stability. However, the application of shear during the holding period, using a paddle mixer, adversely affected stability by disrupting the emulsion microstructure. IVRT studies revealed that the release of lidocaine was higher in the most stable emulsion produced at a holding temperature of 35 °C compared to the least stable emulsion produced at a holding temperature of 25 °C. This suggests that a holding temperature of 35 °C improves both the stability and active release performance. It appears that a slightly higher holding temperature, 35 °C, allows a more flexible and stable emulsifying agent film around the droplets facilitating stabilization of the emulsion. This study offers valuable insights into the relationship between process parameters at various stages of manufacture, microstructure, and various quality attributes of emulsion cream systems. The knowledge gained will facilitate improved design and optimization of robust manufacturing processes, ensuring the production of the formulations with the desired critical quality attributes.