24 February 2020 in Nature Geoscience
NASA’s InSight (Interior exploration using Seismic Investigations, Geodesy and Heat Transport) mission landed in Elysium Planitia on Mars on 26 November 2018. It aims to determine the interior structure, composition and thermal state of Mars, as well as constrain present-day seismicity and impact cratering rates. Such information is key to understanding the differentiation and subsequent thermal evolution of Mars, and thus the forces that shape the planet’s surface geology and volatile processes. Here we report an overview of the first ten months of geophysical observations by InSight. As of 30 September 2019, 174 seismic events have been recorded by the lander’s seismometer, including over 20 events of moment magnitude Mw = 3–4. The detections thus far are consistent with tectonic origins, with no impact-induced seismicity yet observed, and indicate a seismically active planet. An assessment of these detections suggests that the frequency of global seismic events below approximately Mw = 3 is similar to that of terrestrial intraplate seismic activity, but there are fewer larger quakes; no quakes exceeding Mw = 4 have been observed. The lander’s other instruments—two cameras, atmospheric pressure, temperature and wind sensors, a magnetometer and a radiometer—have yielded much more than the intended supporting data for seismometer noise characterization: magnetic field measurements indicate a local magnetic field that is ten-times stronger than orbital estimates and meteorological measurements reveal a more dynamic atmosphere than expected, hosting baroclinic and gravity waves and convective vortices. With the mission due to last for an entire Martian year or longer, these results will be built on by further measurements by the InSight lander.
14 July 2021 in Journal of Geophysical Research: Planets
The heat flow and physical properties package (HP3) of the InSight Mars mission is an instrument package designed to determine the martian planetary heat flow. To this end, the package was designed to emplace sensors into the martian subsurface and measure the thermal conductivity as well as the geothermal gradient in the 0–5 m depth range. After emplacing the probe to a tip depth of 0.37 m, a first reliable measurement of the average soil thermal conductivity in the 0.03–0.37 m depth range was performed. Using the HP3 mole as a modified line heat source, we determined a soil thermal conductivity of 0.039 ± 0.002 W m−1 K−1, consistent with the results of orbital and in‐situ thermal inertia estimates. This low thermal conductivity implies that 85%–95% of all particles are smaller than 104–173 μm and suggests that soil cementation is minimal, contrary to the considerable degree of cementation suggested by image data. Rather, cementing agents like salts could be distributed in the form of grain coatings instead. Soil densities compatible with the measurements are kg m−3, indicating soil porosities of %.
1 February 2020 in Planetary and Space Science
1 November 2019 in Acta Astronautica
26 May 2020 in Earth and Space Science
The Heatflow and Physical Properties Package (HP3) radiometer is currently operating on Mars, observing two spots approximately 1 and 3 m north‐north‐west of the InSight lander. The instrument has primary sensors that are sensitive in the range of 8 to 14 μm and two more sensors with more narrow spectral ranges per field of view. The radiometer underwent radiometric and geometric calibration at DLR—Berlin; and on Mars radiometric self‐calibration is performed regularly. The self‐calibration confirms that one of the two primary sensors has been stable since the ground calibration, but environmental parameters that are likely associated with the thermal contact of sensor and instrument main body may have slightly changed. The other primary sensor has increased in sensitivity for an unknown reason but is still within expectation from the sensor design. The uncertainty of the two primary sensors is approximately 3 K at night, with somewhat larger errors in the late afternoon. This estimate includes the effect of sensitivity changes that would be too small to be reliably detected by the self‐calibration.
9 August 2021 in Geophysical Research Letters
We use the Martian surface temperature response to Phobos transits observed next to the InSight lander in Elysium Planitia to constrain the thermal properties of the uppermost layer of regolith. Modeled transit lightcurves validated by solar panel current measurements are used to modify the boundary conditions of a 1D heat conduction model. We test several model parameter sets, varying the thickness and thermal conductivity of the top layer to explore the range of parameters that match the observed temperature response within its uncertainty both during the eclipse as well as the full diurnal cycle. The measurements indicate a thermal inertia (TI) of in the uppermost layer of 0.2–4 mm, significantly smaller than the TI of derived from the diurnal temperature curve. This could be explained by larger particles, higher density, or some or slightly higher amount of cementation in the lower layers.