15 June 2016 in Journal of Geophysical Research: Planets
While the detection of CO2 ice has only been reported outside the Martian polar regions at very high elevation (i.e., Elysium, Olympus Mons, and the Tharsis Montes), nighttime surface observations by the Mars Climate Sounder on board the Mars Reconnaissance Orbiter document the widespread occurrence of atmospherically corrected ground temperatures consistent with the presence of extensive carbon dioxide frost deposits in the dusty low thermal inertia units at middle/low latitudes. Thermal infrared emissivities, interpreted in conjunction with mass balance modeling, suggest micrometer size CO2 ice crystals forming optically thin layers never exceeding a few hundreds of microns in thickness (i.e., 10−2 kg m−2) locally, which is insufficient to generate a measurable diurnal pressure cycle (<<0.1% of the Martian atmosphere). Atmospheric temperatures at middle/low latitudes are not consistent with precipitation of CO2 ice, suggesting that condensation occurs on the surface. The recurring growth and sublimation of CO2 ice on Martian dusty terrains may be an important process preventing soil induration and promoting dynamic phenomena (soil avalanching and fluidization and regolith gardening), maintaining a reservoir of micrometer size dust particles that are mobile and available for lifting. The discovery of this diurnal CO2 cycle represents an important step forward in our understanding of the way the Martian atmosphere interacts with the surface.
20 July 2022 in Journal of Geophysical Research: Planets
14 July 2021 in Journal of Geophysical Research: Planets
The heat flow and physical properties package (HP3) of the InSight Mars mission is an instrument package designed to determine the martian planetary heat flow. To this end, the package was designed to emplace sensors into the martian subsurface and measure the thermal conductivity as well as the geothermal gradient in the 0–5 m depth range. After emplacing the probe to a tip depth of 0.37 m, a first reliable measurement of the average soil thermal conductivity in the 0.03–0.37 m depth range was performed. Using the HP3 mole as a modified line heat source, we determined a soil thermal conductivity of 0.039 ± 0.002 W m−1 K−1, consistent with the results of orbital and in‐situ thermal inertia estimates. This low thermal conductivity implies that 85%–95% of all particles are smaller than 104–173 μm and suggests that soil cementation is minimal, contrary to the considerable degree of cementation suggested by image data. Rather, cementing agents like salts could be distributed in the form of grain coatings instead. Soil densities compatible with the measurements are kg m−3, indicating soil porosities of %.
31 May 2018 in Journal of Geophysical Research: Planets
We compare the thermophysical properties and particle sizes derived from the Mars Science Laboratory rover's Ground Temperature Sensor of the Bagnold dunes, specifically Namib dune, to those derived orbitally from Thermal Emission Imaging System, ultimately linking these measurements to ground truth particle sizes determined from Mars Hand Lens Imager images. In general, we find that all three datasets report consistent particle sizes for the Bagnold dunes (~110–350 μm and are within measurement and model uncertainties), indicating that particle sizes of homogeneous materials inferred from temperature measurements and thermophysical models are reliable. Furthermore, we examine the effects of two physical characteristics that could influence the modeled thermal inertia and particle sizes, including (1) fine‐scale (centimeter to meter scale) ripples and (2) thin layering of indurated/armored materials. To first order, we find that small‐scale ripples and thin (approximately centimeter scale) layers do not significantly affect the determination of bulk thermal inertia from orbital thermal data using a single nighttime temperature. Modeling of a layer of coarse or indurated material reveals that a thin layer (< ~5 mm; similar to what was observed by the Curiosity rover) would not significantly change the observed thermal properties of the surface and would be dominated by the properties of the underlying material. Thermal inertia and particle sizes of relatively homogeneous materials derived from nighttime orbital data should be considered as reliable, as long as there are no significant subpixel anisothermality effects (e.g., lateral mixing of multiple thermophysically distinct materials).
7 August 2020 in Journal of Geophysical Research: Planets
Comprehensive analysis of remote sensing data used to select the Interior Exploration using Seismic Investigations, Geodesy and Heat Transport (InSight) landing site correctly predicted the atmospheric temperature and pressure profile during entry and descent, the safe landing surface, and the geologic setting of the site. The smooth plains upon which the InSight landing site is located were accurately predicted to be generally similar to the Mars Exploration Rover Spirit landing site with relatively low rock abundance, low slopes, and a moderately dusty surface with a 3–10 m impact fragmented regolith over Hesperian to Early Amazonian basaltic lava flows. The deceleration profile and surface pressure encountered by the spacecraft during entry, descent, and landing compared well (within 1σ) of the envelope of modeled temperature profiles and the expected surface pressure. Orbital estimates of thermal inertia are similar to surface radiometer measurements, and materials at the surface are dominated by poorly consolidated sand as expected. Thin coatings of bright atmospheric dust on the surface were as indicated by orbital albedo and dust cover index measurements. Orbital estimates of rock abundance from shadow measurements in high‐resolution images and thermal differencing indicated very low rock abundance and surface counts show 1–4% area covered by rocks. Slopes at 100 to 5 m length scale measured from orbital topographic and radar data correctly indicated a surface comparably smooth and flat as the two smoothest landing sites (Opportunity and Phoenix). Thermal inertia and radar data indicated the surface would be load bearing as found.