18 August 2023 in IEEE Transactions on Applied Superconductivity
In five and a half years, the ColdFlux project under the IARPA SuperTools program pushed the boundaries of digital and analog superconductor electronic design automation (S-EDA) tools. The SuperTools program demanded significant beyond-state-of-the-art deliverables in four main areas: RTL synthesis, architectures, and verification; analog design and layout synthesis; physical design and test; and technology CAD and cell library design. Through the work of academic groups scattered over four continents, the ColdFlux effort forged into a powerful set of open-source and commercial S-EDA tools unlike any before, rivaled only by a commercial toolchain from Synopsys under the same SuperTools umbrella. We present an overview of the tools from where we started to the eventual project deliverables. These include powerful simulation and extraction engines, magnetic field and flux trapping analysis, advanced clocking methods, multi-chip interface extraction and verification, unified multi-layer design-rule compliant track blocks for automated place and route of both rapid single flux quantum (RSFQ) and adiabatic quantum-flux-parametron (AQFP) cells, models and tools for validation and test, multi-bit single flux quantum (SFQ) cells, architecture innovations for full CPU designs and more. Comprehensive cell libraries and a process design kit (PDK) were developed with the ColdFlux tools. The AQFP cell library features a logically rich collection of 80+ cells, including 3- and 5-input logic gates, signal-driving boosters, and refined RSFQ-to-AQFP interfaces, while the RSFQ library has 30+ cells. Finally, we discuss how the full toolchain enables and enhances the superconductor IC design process.
2 March 2023 in IEEE Transactions on Applied Superconductivity
Thermal noise requires careful consideration during the design process of RSFQ circuits since it reduces circuit operating margins and can cause switching errors. Bit error rate (BER) provides a useful means of analysing the effect of this noise on a circuit. With tools developed under the IARPA SuperTools project, we present an implementation of the Monte-Carlo technique for determining BER via simulation. The Monte-Carlo method has been considered previously but not widely implemented due to slow simulation times preventing the determination of small BER values. We use JoSIM – an efficient simulator with SPICE syntax that allows for the simulation of superconducting components and noise sources with improved speed over older superconductor simulators. This speed improvement makes the Monte-Carlo method viable. The simulated BER is plotted against bias current with values in the low-BER region interpolated from the simulated values using MATLAB. We show how the results need to be used as a further qualifier of circuit performance for the characterization of a logic cell library.
23 January 2024 in IEEE Transactions on Applied Superconductivity
A bi-SQUID consisting of three Josephson junctions has been shown to provide improved linearity in the voltage-flux response when compared with conventional two junction dc SQUIDs. It had also been demonstrated that this improved linearity extends to SQUID arrays and SQIFs constructed using bi-SQUIDs. Experimental results for these arrays have typically been compared with results obtained from mathematical modelling since the manual creation of a complete model that can be simulated for each design is prohibitively time consuming and complex. We present a method of simulating such designs using superconducting EDA tools. Complete circuit models are obtained using the compact model extraction tool included in InductEx-LVS. These models include the Josephson junctions, inductors, resistors and all magnetic couplings from the layout. The models are simulated using JoSIM Superconductor Circuit Simulator to obtain the voltage-flux response. We discuss how the results compare with simulated results for designs that use conventional dc SQUIDs as well as with experimentally verified bi-SQUID designs from literature. Additionally, we consider the advantages and disadvantages of different flux bias application methods for 2D bi-SQUID SQIF designs.
24 November 2025 in IEEE Transactions on Applied Superconductivity
Quantized magnetic flux trapped during cooldown in superconducting integrated circuits, particularly in thin-film ground planes, couples to nearby circuit structures. The coupling from such fluxons is known to degrade circuit operating margins, or to cause outright operational failure. Measurement of the likely location of one or more trapped fluxons during circuit operation, as well as before and after defluxing steps, can help improve defluxing methods and increase circuit operating margins. A bi-SQUID is a device consisting of three Josephson junctions, which demonstrates improved linearity in the voltage–flux response over conventional dc SQUIDs. Conventional dc SQUIDs are being considered as a means of implementing trapped flux detection. Due to the improved linearity of bi-SQUIDs, we investigate their suitability for the same purpose. We present simulation results comparing the sensitivity of different bi-SQUID designs and layout structures to trapped flux and compare bi-SQUID results with a conventional dc SQUID.