Yoshihiko Akamine

Yoshihiko Akamine

Auto-generated profile, based on publicly available information

Yoshihiko Akamine

Department of Electrical and Electronic Engineering, Tokyo Institute of Technology, Tokyo, Japan

Research Focus & Metrics

Academic Career Length

21Years (2006-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2006 in Journal of Environmental Engineering (Transactions of AIJ)
Verified
Journal Article
Open access
PDF file
TKTakashi Kurabuchi
Takashi Kurabuchi
MOMasaaki Ohba
Masaaki Ohba
TETomoyuki Endo
Tomoyuki Endo
YAYoshihiko Akamine
Yoshihiko Akamine
Anew modd llas been proposed f()r evaluating tho discharge coe 価 cient and now angle at an inflow opening fbr cross ・ ven 田 ation based on the previous analysis of the flow struCture by the Large Eddy Simulation . This model is based on the idca that the crossventilation fiow structure in the vicinity of an inflow opening creates dynamic similarity under the。ondition 血 紬 e r飢 io of 。rossventi 圃 on driv 洫 g pressure to dyn ic pressure

3 February 2023 in IEEE Transactions on Instrumentation and Measurement
Verified
Journal Article
Closed access
TWTakuma Watanabe
Takuma Watanabe
YAYoshihiko Akamine
Yoshihiko Akamine
This study aims to provide practical information regarding the development of a cost-effective test model for low-cost radar cross-section (RCS) measurements. Two major possible approaches for reducing the manufacturing cost of a model are replacing the molding material with an inexpensive one and measuring a scaled-down model with a higher operating frequency. In this study, the former was achieved using a resin-made model coated with a conductive paste to imitate a complete metallic model. According to the scaling laws, the entire geometry, including the surface roughness of the model because of the conductive paint, must be appropriately scaled down. Because this roughness scaling is practically infeasible, we experimentally prove that, if an appropriate molding material is selected, shape-only scaling is valid without roughness scaling. As a preliminary study, two types of polyurethane resins with different densities were tested for their suitability for RCS measurements, and the resin with the higher density was shown to be appropriate for the RCS test model. Based on this preliminary study, 1/20- and 1/40-scale aircraft models were manufactured using aluminum or polyurethane resin, and their RCS values were measured to demonstrate that almost equivalent RCS patterns could be obtained. Therefore, low-cost RCS testing was achieved using the resin-made scaled model.

10 April 2023 in IEEE Transactions on Antennas and Propagation
Verified
Journal Article
Closed access
YAYoshihiko Akamine
Yoshihiko Akamine
TTTakashi Tomura
Takashi Tomura
JHJiro Hirokawa
Jiro Hirokawa
This paper proposes a new single-cut scattered field transformation method. The method extends the existing radiation reflector model to the case where the measurement distances from a target under test to a transmitter (TX) and a receiver (RX) are different. The method is applied to bistatic measurements by using the monostatic to bistatic equivalence theorem (MBET). The new method is based on the Born approximation and has features: (1) a scattered field including not only a far-field but a near-field can be predicted from measured near-field samples, where the measurement distances from a target under test to the TX and RX can be different, (2) the scattered field with a zero bistatic angle and the field with the non-zero bistatic angle where the MBET holds can be predicted, (3) the computational time is practical for a large target, and (4) the implementation of the code is easy. The algorithm of the method has simply three steps: inverse Fourier transformation (FT) is implemented with the measured near-field samples, the samples with inverse FT are multiplied by a novel weighting factor, and the scattered field is predicted by taking FT of the weighted samples. The proposed method is experimentally and numerically verified.

17 April 2024 in IEEE Transactions on Antennas and Propagation
Verified
Journal Article
Open access
YAYoshihiko Akamine
Yoshihiko Akamine
TTTakashi Tomura
Takashi Tomura
JHJiro Hirokawa
Jiro Hirokawa
This article proposes a new scattered field transformation method for cylindrical scan system based on the Born approximation. The novelty of the method includes: 1) a far-field (FF) can be predicted from measured near-field (NF) samples with an electrically large target for all the spatial dimensions; 2) measurement distances from the origin of the coordinates in the radial direction to a transmitter (TX) and a receiver (RX) can be different; 3) a bistatic FF can be predicted along an elevation angle and 4) the computation time is less than one minute in each azimuth cut-plane of the cylindrical scan for a large target with dimensions about 400 times that of the wavelength. We have already reported the method for a single-cut scan, and this is extended to the two-dimensional cylindrical scan in this article. The advantages of the proposed method over the reported single-cut method are the requirements of 1) and 3) mentioned above. Although the proposed technique can predict the near-field (NF) as well, the procedure to predict the FF is different from that of the NF prediction. Thus, this article focuses on the FF prediction. The proposed method is experimentally and numerically verified.

1 January 2012 in Journal of Environmental Engineering (Transactions of AIJ)
Verified
Journal Article
Open access
TGTomonobu Goto
Tomonobu Goto
MOMasaaki Ohba
Masaaki Ohba
TKTakashi Kurabuchi
Takashi Kurabuchi
TETomoyuki Endo
Tomoyuki Endo
YAYoshihiko Akamine
Yoshihiko Akamine
KTKenji Tsukamoto
Kenji Tsukamoto

1 January 2007 in Journal of Environmental Engineering (Transactions of AIJ)
Verified
Journal Article
Open access
MOMasaaki Ohba
Masaaki Ohba
TKTakashi Kurabuchi
Takashi Kurabuchi
TGTomonobu Goto
Tomonobu Goto
TETomoyuki Endo
Tomoyuki Endo
YAYoshihiko Akamine
Yoshihiko Akamine
TNToshihiro Nonaka
Toshihiro Nonaka