The purpose of this paper was to analyze palm oil biodiesel production under different conditions and to verify the relationships between production variables in order to optimize biofuel production using response surface methodology (RSM). Biodiesel was produced through transesterification process by methyl route and alkali catalyst (NaOH) 1% (m/m). The analyzed variables were: four molar ratios (3:1, 4:1, 6:1 and 8:1); three temperature reactions (45°, 52° and 60°C); and three time reactions (40, 60 and 80 minutes). For the palm oil biodiesel production, the highest yield was 93%, obtained via a molar rate of 3:1, 52°C and 60 minutes. This result differs from previous studies that found a higher yield with molar ratio increases, implying greater expenses of methanol. Kinetic viscosity and specific mass were also analyzed, and the values are within the Brazilian, American, and European standards. The results showed that the most influent factor in biodiesel production was the molar rate. In relation to the biodiesel characterization, using the RMN H1 technique, it was possible to obtain the transesterification reaction yield of 79.50% for the 3:1 palm oil biodiesel. Through gas chromatography, it can be verified that the predominant fatty acids in the samples were palmitic and oleic acids.
To maintain seed and soil quality of pumpkin, energy knowledge associated with processing and storage stages is strategic for the optimization of the thermodynamic processes needed for product stabilization. Thus, the objective of this study was to determine isosteric heat, differential entropy, and Gibbs free energy within a temperature range from 20 to 70° C, and relative air humidity levels between 10.75 and 85.11%. The study was based on empirical data for water activity determination. As a result, we verified that as moisture content decreased, the integral isosteric heat of the product increased from 2502.35 to 6231.17 kJ kg-1, differential entropy raised from 1.18 to 12.43 kJ kg-1 K-1, and Gibbs free energy ranged from -243.84 to -432.59 kJ kg-1. Thus, we concluded that the lower the water availability in seeds, the greater the energetic requirement for its removal, as there is a major interaction between water and the product (seeds), indicating an increasingly less spontaneous desorption process.
1 December 2017 in Revista Brasileira de Engenharia Agrícola E Ambiental
This study focuses on the determination of the hygroscopic equilibrium and isosteric heat of the aji chili pepper (Capsicum baccatum) under different controlled temperature and relative air humidity conditions. In addition, the objective was to adjust the model among the existing literature models that best represent the isothermal sorption behavior, as well as propose a new model to represent this phenomenon. Having obtained the mathematical models and experimental data, the best model and parameters that represent the hygroscopicity and the isosteric heat satisfactorily was determined. The temperatures used were 30, 55, and 70 °C, with water activity levels from 0.11 to 0.84. The model that best fit the data had a R2 value of 0.97. The integral isosteric heat of sorption for ‘Dedo-de-Moça’ chili pepper within a moisture content from 0.07 to 0.55 (dry basis) ranged from 3641.66 to 2614.38 kJ kg-1.
Com o intuito de analisar a dinâmica de sorção e a energia necessária para a vaporização da água na desidratação do bagaço da cana-de-açúcar, o presente trabalho teve como objetivo a determinação de seu equilíbrio higroscópico e calor isostérico, a partir de diferentes condições controladas de temperatura (20; 40; 55 e 70 ºC) e umidade relativa do ar (10; 12; 17; 18; 30; 40; 45; 50; 60 e 85%), assim como avaliar, entre diversos modelos descritos na literatura, o que melhor represente o comportamento de sorção. Como resultado, foi verificado que o modelo que melhor se ajustou aos dados empíricos do processo de sorção do bagaço de cana-de-açúcar foi o Modelo de Henderson Modificado, com coeficiente de determinação de 0,972, enquanto o calor isostérico integral de dessorção variou de 2524,09 a 2951,95 kJ kg-1, para os teores de água de equilíbrio de 0,014 a 0,170 b.s., respectivamente.
1 October 2019 in Revista Brasileira de Engenharia Agrícola E Ambiental
Diesel cycle engines are widely used in agricultural machinery. Biodiesel offers the possibility of partial or total replacement of mineral diesel, thus reducing the dependence of agriculture on this non-renewable resource and decreasing pollutant emissions. The objective of this study was to evaluate the emissions of CO, NOx, SO2, CO2, and O2 from various biodiesel mixtures (B0 = 0%, B7 = 7%, B10 = 10%, B20 = 20%, B30 = 30% and B100 = 100%) in a single-cylinder tractor engine at 1000, 1600 and 2400 rpm. The exhaust gases were identified using a gas probe meter. Fuels with a higher percentage of biodiesel have the lowest SO2 emissions, with the B30 mixture releasing 65.78, 52.47 and 32.25 parts per million at 1000, 1600 and 2000 rpm, respectively. Nitrous oxides and carbon dioxide emissions decreases with higher engine rotation speed. Higher percentages of biodiesel result in less polluting fuels.
1 February 2026 in Revista Brasileira de Engenharia Agrícola E Ambiental
Banana drying, one of the most cost-effective methods of fruit dehydration, often faces challenges related to drying time and slice thickness. The time required for drying varies depending on temperature, humidity, and slice thickness, making it essential to ensure effective moisture removal without compromising product quality. This study aimed to analyze the influence of drying air temperature and slice thickness on drying time. Bananas were dried at four different temperatures (35, 45, 55, and 70 °C) and with five different slice thicknesses (5, 10, 20 mm, half (14.41 to 16.13 mm) [half the fruit’s thickness], and whole (28.82 to 32.26) [entire fruit thickness]). To assess drying time, mathematical models (Lewis, Page, Henderson, and Thompson) were tested. The Page model best fitted the drying curves, with R2 = 0.99 and p ≤ 0.01. According to Tukey’s test at p < 0.05, both temperature and slice thickness had a significant effect on drying time, which ranged from 4 to 66 hours. A drying temperature of 55 °C and slice thickness of 10 mm resulted in a significantly more efficient drying process.