Muslich Hartadi Sutanto

Muslich Hartadi Sutanto

Auto-generated profile, based on publicly available information

Muslich Hartadi Sutanto

Department of Civil & Environmental Engineering, Universiti Teknologi PETRONAS, Malaysia

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 October 2021 in KSCE Journal of Civil Engineering
Verified
Journal Article
Open access
PDF file
Afnan AhmadAfnan Ahmad
Afnan Ahmad
MSMuslich Hartadi Sutanto
Muslich Hartadi Sutanto
MAMohammed Ali Al-Bared
Mohammed Ali Al-Bared
IHIndra Sati Hamonangan Harahap
Indra Sati Hamonangan Harahap
SASeyed Vahid Alavi Nezhad Khalil Abad
Seyed Vahid Alavi Nezhad Khalil Abad
MKMudassir Ali khan Ali Khan
Mudassir Ali khan Ali Khan
Peat is formed by the degradation of plants and animals in the lack of oxygen and is widely known for its very weak geotechnical characteristics. This is the reason to be considered as an unsuitable foundation soil for construction activities. Several attempts have been made to characterize and stabilize peat soil to make construction viable. This study encapsulates an extensive literature review of the available published data for Atterberg limits, consolidation, and stabilization of peat soil using traditional additives, especially cement and lime. Moreover, peat formation and distribution around the world are also discussed. The analysis of the gathered data shows that peat soils having a high amount of fibers may suffer a large amount of secondary consolidation when the load is applied. Besides, the compressibility factors vary for Malaysian peat due to different water and organic contents. The improvement of peat soil is challenging and expensive, requiring an extra amount of stabilizer for the initiation of the stabilization process. However, the optimum and threshold stabilizer’s dosage for peat is also a challenging task to predict due to several factors affecting the stabilization process. Lastly, the study concludes with recommendations on the implication of the fall cone and thread rolling tests for the determination of Atterberg limits of fibrous peat, effective consolidometer for peat, and utilization of traditional additives for peat soil stabilization.

1 May 2022 in IOP Conference Series: Earth and Environmental Science
Verified
Conference Paper
Open access
MKMuhammad Imran Khan
Muhammad Imran Khan
SASiti Yusrina Binti Zainal Abidin
Siti Yusrina Binti Zainal Abidin
MSMuslich Hartadi Sutanto
Muslich Hartadi Sutanto
FWFadhli Wong
Fadhli Wong
MBMastura Bujang
Mastura Bujang
Due to the visco-elastic nature, the performance of flexible pavements depends on temperature and loading conditions. This study investigates the influence of different speeds of vehicle and binder type on stiffness modulus and the corresponding pavement life. The filed data was collected from the pavement section at Bukit Mertajam, Penang, Malaysia. The data were used to determine the stiffness of binder and corresponding stiffness of wearing and binder courses at different vehicle speeds (30, 50, 70 and 80 km/h) using analytical equations. The data of layer properties (stiffness and poison’s ratio) and axle loading (wheel load, tyre configuration) were incorporated in BISAR software to determine the horizontal tensile strain at bottom of binder layer and vertical compressive strain at top of subgrade. The strains were then used to predict pavement life passed on fatigue and rutting failure criteria. It was concluded that increasing the speed of the vehicle (from 30 km/h to 80 km/h) causes about 24% increase in stiffness modulus of wearing course. Similarly, asphalt mixture with Pen 80/100 grade bitumen has a lower stiffness modulus than Pen 60/70 grade bitumen. Furthermore, reducing vehicle speed (i.e., increasing loading time) causes a reduction in fatigue and rutting life of the pavement. Therefore, it is required to consider the speed of the vehicle while designing flexible pavement in addition to other mixed design considerations.

1 May 2022 in IOP Conference Series: Earth and Environmental Science
Verified
Conference Paper
Open access
AUALIYU USMAN
ALIYU USMAN
MSM H Sutanto
M H Sutanto
MNM Napiah
M Napiah
AAAbdulnaser Al-Sabaeei
Abdulnaser Al-Sabaeei
NYNura Shehu Aliyu Yaro
Nura Shehu Aliyu Yaro
SSS M Saeed
S M Saeed
Recently, the excessive quantity of waste polyethylene terephthalate (WPET) creates a significant environmental concern globally. One way to reuse WPET is in the pavement industry as secondary materials. Nevertheless, based on works of literature review on the use of WPET in asphalt materials, inconsistent findings were reported with an increase and decrease in mechanical properties. To overcome this issue, gamma radiation has been utilized on the WPET. This study investigated the effect of using non-irradiated and irradiated WPET on some engineering properties of asphalt mixes. Marshall Samples incorporating a various amount of WPET (Plastiphalt); 0%, 0.5%, 1.0%, 1.5%, 2.0% and 2.5% by weight of total aggregates were tested based on Marshall Stability (MS), indirect tensile strength (ITS), and resistance to moisture damage. The results of x-ray diffraction (XRD) on the irradiated WPET showed that the degree of crystallinity had increased. The results of Marshall Stability (MS) showed an enhancement with increasing WPET content up to 2.0% for the plastiphalt mixes. Marshall Quotient, and ITS show a decreasing trend with increasing WPET amount for the plastiphalt mixes. Furthermore, results on moisture damage resistance indicated that indirect tensile strength and Marshall Stability ratios were marginally increased for plastiphalt mixes compared to the reference mixture (0% WPET). Comparing the moisture sensitivity tolerance results for the WPET modified mixes shows that irradiated WPET plastiphalt mixes had a better outcome than non-irradiated WPET plastiphalt mixes.