21 June 2022 in IEEE Robotics and Automation Letters
Faster robotic picking of objects can improve industrial production throughput. A gripper design with appropriate control strategy is demonstrated to pick objects at high speed, while being tolerant to unintentional collisions. The design has a quasi–direct drive with backdrivable, rigid finger mechanism to transfer collision forces with minimal delay towards the motor side. These forces are detected based on band–pass filtered momentum and motor speed monitoring. The motor velocity is observed through Kalman filtering in order to reduce noise in the low–level control loop and band–pass momentum observer, resulting in a higher collision detection sensitivity. On a higher level, the path of the gripper is planned with respect to the trade–off picking speed versus collision tolerance, quantified by the remaining gripper stroke upon impact. The gripper collision tolerance was experimentally verified in several scenarios during high–speed object picking where it mitigated collisions up to 0.6 m/s.
14 January 2021 in IEEE Robotics and Automation Letters
Industrial robots can collide due to malfunctioning, wrong user input or unforeseen changes in the environment in which they operate. Different solutions exist to minimize the damage caused by a collision, either absorbed by the environment or by the robot itself. The specific solution depends on the type, size and dynamics of the robot. For high-speed industrial robots, the challenge is in dealing with the large kinetic energy upon impact without compromising the dynamic response during normal operation. The Combined Friction Cam Clutch (CFCC) is proposed as a solution for this problem. We provide a custom mechanical design and derive equations to calculate the threshold and residual torque which are identified as key design metrics. The concept is validated experimentally on a test bench using a prototype of the set-up.
8 November 2022 in IEEE Robotics and Automation Letters
A hybrid high-speed industrial collaborative robot can switch between collaborative mode and high-speed mode, combining the advantages of both. While promising, this concept comes with some challenges such as dealing with collisions at high speed. An overload clutch with integrated torque sensing and clutch decoupling detection is presented as enabling technology. Both joint torque sensing and clutch decoupling detection are realized with the same capacitive measurement hardware that consists of paired electrodes. A prototype device is experimentally validated through comparison with a reference torque sensor.
4 October 2024 in IEEE Transactions on Robotics
Robots are more often deployed in unstructured or unpredictable environments. Particularly collisions at high speed can severely damage the drivetrains and joint bearings of robots. In order to avoid such collisions, path planners exist that adapt the robot's original trajectory online if a collision hazard is detected. These methods require additional sensors such as cameras, are computationally costly and never flawless due to occlusions. Another approach is to incorporate a cost function that promotes collision tolerance while planning the initial trajectory. The resulting impact-aware path plan minimizes the chance of robot hardware damage if a collision would occur. Two algorithms are presented to assess collision tolerance in high-speed robots, taking into account factors such as robot pose, impact direction, and maximum intermittent loading of the gearboxes and bearings. The first algorithm is more general while the second assumes the presence of joint overload clutches that decouple upon impact. These algorithms are applied to plan an impact-aware path for a custom 6-axis series clutched actuated robot that serves as use case. Both for the case with and without clutches, a generic impact-aware plan is presented as well as at least one derived, heuristic alternative. Without clutches, trajectories that are perpendicular to the end effector flange were found to be desirable, as they allow the robot to mitigate the highest collision force without overloading the gearboxes or bearings. On the other hand, with clutches, trajectories that are parallel to the end effector flange were found to be more collision tolerant. The effect of impact direction was also experimentally validated using the custom 6-axis robot. Collisions at velocities up to 1.2m/s were mitigated through the combination of impact-aware path planning and series clutched actuation.
23 April 2024 in Journal of Mechanisms and Robotics
Collisions at high-speed can severely damage robots with non-backdrivable drivetrains. Adding an overload clutch in series can improve the robot’s collision tolerance without compromising its high dynamic performance. This paper aims at determining the speed above which overload clutches are required in a two-link manipulator arm. Furthermore, the optimal clutch topology as function of the impact velocity is investigated. Third, it is evaluated if adding clutches can lower the impact force on the arm. Finally, the maximum speed is identified below which impact-aware robot control is possible. The latter requires that none of the clutches decouple during an intentional collision with the environment. These answers are obtained through collision simulations and experiments with a custom build two-link arm. It was found that adding a clutch reduces the torque experienced by the drivetrain by an order of magnitude and below the limit momentary peak torque of the strain wave gears that are used. Adding a clutch to the elbow joint of the two-link arm was effective in protecting the shoulder as well if the impact occurred at the tool center point. With respect to a rigid elbow joint, the clutched elbow joint reduced the collision force at the tool by only 8%. To demonstrate that the arm is impact-aware, a box of 8 kg is approached, impacted, and pushed at 1 m/s without decoupling a clutch, nor damaging the robot’s hardware.
28 November 2024 in IEEE Sensors Journal
Robotic manipulation relies on accurate force sensing and control mechanisms to ensure efficient and safe operation. This paper presents a novel approach to enhance robotic manipulation capabilities by integrating a barometric tactile sensor with a quasi-direct drive gripper (QDDG). The synergy between these technologies addresses inherent limitations: QDDGs struggle with high current requirements and potential overheating, while tactile sensors often have restricted force ranges and sampling rates. By fusing data from these systems using an adaptive sensor fusion model, this study improves force estimation accuracy, extends force range capability, and boosts sampling rates up to 100 Hz. The integrated approach not only enhances grasping efficiency but also enables autonomous adjustment of grip force levels to prevent slippage. Experimental results demonstrate significant improvements in force estimation accuracy over individual sensor outputs, validating the effectiveness of the proposed integration for advanced robotic manipulation tasks. Furthermore, based on this sensor fusion framework, a slip detection and control mechanism was developed capable of grasping and lifting a diverse array of objects with high success-rates (>90%).