Rens Jan Horst

Rens Jan Horst

Auto-generated profile, based on publicly available information

Rens Jan Horst

Eindhoven University of Technology

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
14 October 2025 in Energy & Environmental Science
Verified
Journal Article
Open access
PDF file
RHRens J. Horst
Rens J. Horst
RLRalph van der Linde
Ralph van der Linde
RJRémy R. Jacquemond
Rémy R. Jacquemond
BLBo Liu
Bo Liu
AFAntoni Forner-Cuenca
Antoni Forner-Cuenca
Gas diffusion media are essential components in polymer electrolyte membrane fuel cells and a broad range of electrochemical technologies, enabling efficient mass transport of gas and liquid, electronic and thermal conductivity, and structural integrity under compression. Conventional diffusion media, typically made from carbon fiber substrates with microporous layers, have been extensively post-treated to enhance performance; however, these approaches offer limited control over three-dimensional microstructure, particularly for advanced architectures with bimodal or gradient porosity – which can facilitate multiphase gas and liquid mass transport – and often rely on complex, multi-step processes. These limitations underscore the need for scalable, cost-effective fabrication methods capable of producing much broader geometrical features. Here, we introduce a scalable, bottom-up fabrication method based on non-solvent induced phase separation (NIPS) to produce carbon-based diffusion media with finely tunable microstructures. By systematically varying processing parameters, we generate thin, mechanically robust diffusion media with tailored in-plane and through-plane porosity, including isoporous and bimodal structures. Using microscopy, porosimetry, and electrochemical diagnostics, we correlate microstructural features with single-cell fuel cell performance, revealing their impact on water management and gas transport. We further demonstrate post-treatment strategies to enhance mass transport properties and benchmark the cost and scalability of NIPS fabrication against conventional carbon fiber-based diffusion media via techno-economic analysis. Our findings highlight the potential of NIPS as a versatile and industrially relevant pathway for next-generation diffusion media, offering new design freedoms to optimize fuel cell performance and reduce system-level costs.

5 April 2021 in The European Physical Journal E
Verified
Journal Article
Open access
PDF file
LVLars B. Veldscholte
Lars B. Veldscholte
RHRens J. Horst
Rens J. Horst
SBSissi de Beer
Sissi de Beer
Stable and precise control of humidity is imperative for a wide variety of experiments. However, commercially available humidistats (devices that maintain a constant humidity) are often prohibitively expensive. Here, we present a simple yet effective humidistat for laboratory-scale applications that can be easily and affordably (<€250) constructed based on an Arduino Uno as microcontroller, a set of proportional miniature solenoid valves, a gas washing bottle, and a humidity sensor. The microcontroller implements a PID controller that regulates the ratio of a dry and humid airflow. The design and implementation of the device, including a custom driver circuit for the solenoids, are described in detail, and the firmware is freely available online. Finally, we demonstrate its proper operation and performance through step response and long-term stability tests, which shows settling times of approx. 30 s and an attainable relative humidity range of 10–95%

20 March 2026 in Journal of the Electrochemical Society
Verified
Journal Article
Open access
RHRens J. Horst
Rens J. Horst
AFAntoni Forner-Cuenca
Antoni Forner-Cuenca
Reducing ionomer content in polymer electrolyte fuel cell catalyst layers is key to mitigating oxygen transport losses, yet current fabrication methods deposit ionomer in an uncontrolled manner, often requiring excess loadings to ensure proton conduction. Introducing well-defined proton-conducting functional groups directly onto catalyst supports offers a route to improve transport without relying on high ionomer fractions. Here, we demonstrate direct grafting of sulfonic acid groups onto Pt/Vulcan catalysts using diazonium chemistry. The grafting degree was systematically tuned by adjusting precursor concentration and quantified through water dispersibility measurements, zeta potential analysis, X-ray photoelectron spectroscopy, and acid-base titration. Electrochemical characterization revealed minor reductions in electrochemically active surface area and slight shifts in half-wave and onset potentials. In single-cell testing, however, grafted catalysts enabled improved performance at low ionomer loadings due to enhanced proton conductivity and increased catalyst-layer hydrophilicity, which together promote more efficient proton transport near Pt sites. At higher ionomer contents, performance gains diminished, likely due to unfavorable electrostatic interactions during catalyst-layer formation. Accelerated stress tests indicated that the grafted functionalities remained stable under fuel-cell operating conditions. Overall, diazonium-based sulfonic acid grafting provides a controllable and durable strategy to optimize proton transport and interfacial properties, enabling high performance at reduced ionomer contents.

4 December 2025 in ChemRxiv
Verified
Preprint
Open access
PDF file
RHRens Horst
Rens Horst
AFAntoni Forner-Cuenca
Antoni Forner-Cuenca
Reducing ionomer content in polymer electrolyte fuel cell catalyst layers is key to mitigating oxygen transport losses, yet current fabrication methods deposit ionomer in an uncontrolled manner, often requiring excess loadings to ensure proton conduction. Introducing well-defined proton-conducting groups directly onto catalyst supports offers a route to improve transport without relying on high ionomer fractions. Here, we demonstrate direct grafting of sulfonic acid groups onto Pt/Vulcan catalysts using diazonium chemistry. The grafting degree was systematically tuned by adjusting precursor concentration and quantified through water dispersibility measurements, zeta potential analysis, X-ray photoelectron spectroscopy, and acid–base titration. Electrochemical characterization revealed minor reductions in electrochemically active surface area and slight shifts in half-wave and onset potentials. In single-cell testing, however, grafted catalysts enabled improved performance at low ionomer loadings due to enhanced proton conductivity and increased catalyst-layer hydrophilicity, which together promote more efficient proton transport near Pt sites. At higher ionomer contents, performance gains diminished, likely due to unfavorable electrostatic interactions during catalyst-layer formation. Accelerated stress tests indicated that the grafted functionalities remained stable under fuel-cell operating conditions. Overall, diazonium-based sulfonic acid grafting provides a controllable and durable strategy to optimize proton transport and interfacial properties, enabling high performance at reduced ionomer contents.

9 July 2026 in Journal of the Electrochemical Society
Verified
Journal Article
Open access
PDF file
RHRens J. Horst
Rens J. Horst
AFAntoni Forner-Cuenca
Antoni Forner-Cuenca
The carbon support surface chemistry strongly influences ionomer interactions, water management, and electrochemical performance in polymer electrolyte fuel cell catalyst layers; however, studies that decouple these effects from Pt particle size remain limited. Here, diazonium grafting is applied to commercial 40 wt% Pt/Vulcan and Pt/Ketjenblack catalysts to introduce five aryl functionalities (–NO 2 ,–NH 2 ,–CF 3 ,–COOH,–SO 3 H) spanning a wide range of polarities and wettabilities without altering Pt dispersion. Ex-situ characterization (X-ray photoelectron spectroscopy, thermogravimetric analysis, N 2 physisorption, contact angle, and dynamic vapor sorption) confirms successful functionalization and shows that grafting on Ketjenblack occurs preferentially at external surfaces, reducing pore accessibility. In 5 cm 2 single-cell tests, nitrogen-containing functionalities reduce cathode proton transport resistance, increasing current density at 0.7 V (1.20 vs 1.01 A cm −2 , I/C = 0.6). For hydrophilic and hydrophobic groups, optimal performance depends strongly on the ionomer-to-carbon ratio: hydrophilic functionalities enhance performance at low I/C (0.1) but become detrimental at higher I/C (0.6) due to increased water retention and unfavorable ionomer interactions. These effects are amplified for porous Ketjenblack, where pore blockage offsets gains from surface modification. These findings establish that surface functionalization and support porosity cannot be optimized independently, and suggest that next-generation mesoporous carbon supports could incorporate pore architectures compatible with surface modification.

22 December 2023 in ECS Meeting Abstracts
Verified
Journal Article
Closed access
RHRens Jan Horst
Rens Jan Horst
AFAntoni Forner-Cuenca
Antoni Forner-Cuenca
The development of the next generation of polymer electrolyte fuel cells has become a major focus in the decarbonization of heavy-duty transportation, such as public transport, land, aviation, and maritime freight1. Specifically, there is a need for improved catalyst layers with lower amounts of expensive platinum group metals2, as well as improved mass transport characteristics at high current densities, fluorine-free ionomers, and increased durability3. Achieving an optimal electrode microstructure is crucial in this process, as it influences the mass transport of reactant gases and products2. The chemistry and morphology of the ionomer film determine proton availability and affect oxygen transport and overall catalyst utilization. Thus, it is critical to maintain a delicate balance between the transport of reactants, products, protons, and electrons to ensure optimal cell performance. Traditional catalyst layers are fabricated using catalyst ink dispersions which limits the control over the triple-phase boundary microstructure4. This is problematic as poor distribution of the ionomer has been shown to have a negative impact on fuel cell performance5. It has been observed that some catalytic sites are inundated with ionomer, leading to a high oxygen transport resistance, while other uncoated sites may experience a lack of protons. Moreover, research has shown that the catalyst's active sites can be poisoned by the adsorption of sulfonic acid moieties present in commonly used ionomers. Motivated by these challenges, and the negative environmental impact of conventional fluorinated ionomers, it is essential to develop alternative ionomer chemistries and coating techniques6. To address these challenges, our research focuses on developing innovative synthetic methods that leverage both electrochemical and chemical principles to enable local control of ionomer coating in the catalyst layer. Our interest in these methods originates from their scalability and ability to control the morphology of coatings (e.g. thickness, conformality, porosity and polymer length). We employ grafting techniques based on radical mechanisms to covalently graft conformal ionomer thin films onto conventional Pt/C catalysts to produce improved triple phase boundaries. A vast array of monomers with different kinds of functionalities (e.g. amines, vinylics, diazo-compounds, carboxylates) can be used for grafting, including fluorine-free systems7. In this presentation, I will first describe the synthetic procedure to produce ionomer thin films. Second, we perform ex-situ characterization including electron microscopy, porosimetry and wettability measurements. Furthermore, we study the ionomeric nature of the films by its ion exchange capacity. Subsequently, we screen the most promising samples in single cell tests and compare them against a state-of-the-art benchmark. By combining potentiostatic and impedance-based techniques, we seek to gain insight into the in-operando characteristics of these new electrode materials. Through this comprehensive set of experiments, we aim to elucidate morphology – property – performance relationships for these ionomer thin films to further guide optimization of catalyst microstructures. Acknowledgement: This publication is part of the project 3D-FCoat (3-Dimensional structures for Fuel Cells through advanced Coating techniques) of the research program LIFT which is (partly) financed by the Dutch Research Council (NWO) and Nedstack Fuel Cell Technology B.V. References: Khedekar, K. et al. Adv. Energy Mater. 2021, 11, 2101794, DOI: 10.1002/aenm.202101794 Suter, T.A.M. et al. Adv. Energy Mater. 2021, 11, 2101025, DOI: 10.1002/aenm.202101025 Harzer, G.S. et al. J. Electrochem. Soc. 2018, 165 (10), 770-779, DOI: 10.1149/2.0311810jes Lui, H. et al. Appl. Sci. 2022, 12 (8), 3776, DOI: 10.3390/app12083776 Ott, S. et al. Nat. Mater. 2020, 19, 77-85, DOI: 10.1038/s41563-019-0487-0 Kongkanand, A. et al. J. Phys. Chem. Lett. 2016, 7 (7), 1127-1137, DOI: 10.1021/acs.jpclett.6b00216 Bélanger, D. et al. Chem. Soc. Rev., 2011, 40, 3995-4048, DOI: 10.1039/C0CS00149J