Paul Evans

Paul Evans

Auto-generated profile, based on publicly available information

Paul Evans

University of Nottingham, University Park, Nottingham, UK, NG7 2RD

Research Focus & Metrics

Academic Career Length

17Years (2010-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 December 2013 in Microelectronics Reliability
Verified
Journal Article
Open access
RSR. Skuriat
R. Skuriat
JLJ.F. Li
J.F. Li
PAP.A. Agyakwa
P.A. Agyakwa
NMN. Mattey
N. Mattey
PEP. Evans
P. Evans
CJC.M. Johnson
C.M. Johnson

28 December 2012 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
PEPaul L. Evans
Paul L. Evans
Alberto CastellazziAlberto Castellazzi
Alberto Castellazzi
CJC. Mark Johnson
C. Mark Johnson
Virtual prototyping of power electronic modules aims to allow rapid evaluation of potential designs without the need to resort to building and testing physical prototypes. A key requirement for this process is the ability to quickly generate small, compact models describing the thermal performance of a potential design and this study presents a novel approach for this model generation process. The approach starts with a finite-difference mesh of the proposed design and applies a fast sparse matrix solver (GMRES) to determine the steady-state response to a particular power input. In doing this, approximations for the eigenvalues of the system can also be obtained from the same algorithm. It is shown that these two results can then be used to create small compact models describing the dynamic thermal properties within the design. The method is validated against an analytical solution for 1-D heat conduction and against experimental results for a simple power module. This process can be automated and it is shown that compact models can be generated in around 12 s per power input from the finite-difference mesh of the power module containing 14 623 nodes on a standard desktop PC.

25 May 2015 in IEEE Transactions on Power Electronics
Verified
Journal Article
Open access
PEPaul L. Evans
Paul L. Evans
Alberto CastellazziAlberto Castellazzi
Alberto Castellazzi
CJC. Mark Johnson
C. Mark Johnson
The need for multidisciplinary virtual prototyping in power electronics has been well established, however, design tools capable of facilitating a rapid iterative virtual design process do not exist. A key challenge in developing such tools is identifying and developing modeling techniques which can account for 3-D geometrical design choices without unduly affecting simulation speed. This challenge has been addressed in this paper using model order reduction techniques and a prototype power electronic design tool incorporating these techniques is presented. A relevant electrothermal power module design example is then used to demonstrate the performance of the software and model order reduction techniques. Five design iterations can be evaluated, using 3-D inductive and thermal models, under typical operating and start-up conditions on a desktop PC in less than 15 min. The results are validated experimentally for both thermal and electrical domains.

20 April 2016 in Journal of Electronic Materials
Verified
Journal Article
Open access
PDF file
PAPearl A. Agyakwa
Pearl A. Agyakwa
LYLi Yang
Li Yang
EAElaheh Arjmand
Elaheh Arjmand
PEPaul Evans
Paul Evans
MCMartin R. Corfield
Martin R. Corfield
CJC. Mark Johnson
C. Mark Johnson
Ultrasonically bonded heavy Al wires subjected to a small junction temperature fluctuation under power cycling from 40°C to 70°C were investigated using a non-destructive three-dimensional (3-D) x-ray tomography evaluation approach. The occurrence of irreversible deformation of the microstructure and wear-out under such conditions were demonstrated. The observed microstructures consist of interfacial and inter-granular cracks concentrated in zones of stress intensity, i.e., near heels and emanating from interface precracks. Interfacial voids were also observed within the bond interior. Degradation rates of ‘first’ and ‘stitch’ bonds are compared and contrasted. A correlative microscopy study combining perspectives from optical microscopy with the x-ray tomography results clarifies the damage observed. An estimation of lifetime is made from the results and discussed in the light of existing predictions.

1 September 2020 in IEEE Transactions on Power Electronics
Verified
Journal Article
Open access
KLKe Li
Ke Li
AVArnaud Videt
Arnaud Videt
NINadir Idir
Nadir Idir
PEPaul Leonard Evans
Paul Leonard Evans
CJChristopher Mark Johnson
Christopher Mark Johnson

9 April 2021 in Energies
Verified
Journal Article
Open access
PDF file
KLKe Li
Ke Li
PEPaul Leonard Evans
Paul Leonard Evans
CJChristopher Mark Johnson
Christopher Mark Johnson
AVArnaud Videt
Arnaud Videt
NINadir Idir
Nadir Idir
In order to model GaN-HEMT switching transients and determine power losses, a compact model including dynamic RDSon effect is proposed herein. The model includes mathematical equations to represent device static and capacitance-voltage characteristics, and a behavioural voltage source, which includes multiple RC units to represent different time constants for trapping and detrapping effect from 100 ns to 100 s range. All the required parameters in the model can be obtained by fitting method using a datasheet or experimental characterisation results. The model is then implemented into our developed virtual prototyping software, where the device compact model is co-simulated with a parasitic inductance physical model to obtain the switching waveform. As model order reduction is applied in our software to resolve physical model, the device switching current and voltage waveform can be obtained in the range of minutes. By comparison with experimental measurements, the model is validated to accurately represent device switching transients as well as their spectrum in frequency domain until 100 MHz. In terms of dynamic RDSon value, the mismatch between the model and experimental results is within 10% under different power converter operation conditions in terms of switching frequencies and duty cycles, so designers can use this model to accurately obtain GaN-HEMT power losses due to trapping and detrapping effects for power electronics converters.