Hasan Jubaer

Hasan Jubaer

Auto-generated profile, based on publicly available information

Hasan Jubaer

Department of Mechanical and Nuclear Engineering, Virginia Commonwealth University, 401 West Main Street, P.O. Box 843015, Richmond, VA, 23284-3015, USA

Research Focus & Metrics

Academic Career Length

15Years (2012-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
25 April 2019 in Energy & Environmental Science
Verified
Journal Article
Closed access
PDF file
YXYun Xia
Yun Xia
QHQinfu Hou
Qinfu Hou
HJHasan Jubaer
Hasan Jubaer
YLYang Li
Yang Li
YKYuan Kang
Yuan Kang
Xiwang ZhangXiwang Zhang
Xiwang Zhang
As a low-cost green technology, solar steam generation using nanostructured photothermal materials has been drawing increasing attention in various applications, e.g. seawater desalination, and zero liquid discharge of industrial wastewater. However, the crystallisation of salts on the surface of photothermal materials during steam generation leads to a gradual decline in the water evaporation rate. Herein, this challenge was overcome by a novel design involving controlled water transport, edge-preferential crystallisation and gravity-assisted salt harvesting. The crystallisation sites of the salt were spatially isolated from the water evaporation surface, achieving continuous steam generation and salt harvesting in over 600 hours of non-stop operation. The study provides new insights into the design of solar steam generators and advances their applications in sustainable seawater desalination and wastewater management.

1 January 2019 in Chemical Engineering Research and Design
Verified
Journal Article
Closed access
HJHasan Jubaer
Hasan Jubaer
SASepideh Afshar
Sepideh Afshar
JXJie Xiao
Jie Xiao
XCXiao Dong Chen
Xiao Dong Chen
CSCordelia Selomulya
Cordelia Selomulya
MWMeng Wai Woo
Meng Wai Woo

28 August 2017 in Drying Technology
Verified
Journal Article
Closed access
HJHasan Jubaer
Hasan Jubaer
SASepideh Afshar
Sepideh Afshar
JXJie Xiao
Jie Xiao
XCXiao Dong Chen
Xiao Dong Chen
CSCordelia Selomulya
Cordelia Selomulya
Meng Wai WooMeng Wai Woo
Meng Wai Woo
Shrinkage behavior or the change of droplet diameter in the course of drying is quite diverse and has been the focus of many studies due to its crucial importance in accurate modeling of spray drying. However, the specific impacts of capturing it while performing computational fluid dynamics simulations have not yet been investigated comprehensively. Therefore, this work aimed to directly compare predictions obtained by the perfect shrinkage and linear shrinkage models. As compared to linear shrinkage, the assumption of perfect shrinkage led to a decrease in the surface area as well as an increase in the transport coefficients, resulting in an overall decrease in drying rate. Furthermore, the predicted particle size distribution was significantly affected by the implemented shrinkage model, while contrary to the expectation commonly expressed in the literature, the residence time of the particles was similar for the investigated pilot-scale dryer. Considerable difference ascertained in predicted drying histories, particularly for larger droplets, led to the conclusion that the assumption of perfect shrinkage leads to overprediction of particle stickiness and underestimation of drying rates. This difference is particularly important in modeling phenomena like agglomeration and particle–wall deposition.

28 March 2021 in Drying Technology
Verified
Journal Article
Closed access
RRRamin Razmi
Ramin Razmi
HJHasan Jubaer
Hasan Jubaer
MKMichal Krempski
Michal Krempski
Maciej JaskulskiMaciej Jaskulski
Maciej Jaskulski
JXJie Xiao
Jie Xiao
Meng Wai WooMeng Wai Woo
Meng Wai Woo
Recent initiatives covered in this review can be divided into three broad categories. The first category concerns mathematically describing the spray drying process using a plug-flow model which allows quick what-if evaluations of the process. Intricacies associated with capturing the drying of a range of droplet sizes are discussed. Challenges in adapting the plug-flow simulation approach to counter-current spray drying, which is common in the production of non-heat sensitive detergent powder, was further elaborated. The second broad category features modeling the spray drying process using the Computational Fluid Dynamics technique. A critical review was provided to guide readers on a common dilemma plaguing this area of spray drying modeling. Recent developments in agglomeration modeling in spray dryers are discussed as well. The final part of this review touches on modeling techniques which can be used to predict the development of specific powder qualities. This includes modeling the degree of protein denaturation during spray drying, predicting the characteristics of crystalline type spray dried powder, and determining the properties of the powder surface at the molecular scale.

1 March 2019 in Powder Technology
Verified
Journal Article
Closed access
HJHasan Jubaer
Hasan Jubaer
JXJie Xiao
Jie Xiao
XCXiao Dong Chen
Xiao Dong Chen
CSCordelia Selomulya
Cordelia Selomulya
MWMeng Wai Woo
Meng Wai Woo

1 January 2020 in Powder Technology
Verified
Journal Article
Closed access
HJHasan Jubaer
Hasan Jubaer
SASepideh Afshar
Sepideh Afshar
GMGuénolé Le Maout
Guénolé Le Maout
SMSerge Mejean
Serge Mejean
CSCordelia Selomulya
Cordelia Selomulya
MWMeng Wai Woo
Meng Wai Woo