Houria Hebhoub

Houria Hebhoub

Auto-generated profile, based on publicly available information

Houria Hebhoub

Civil Engineering Department, Faculty of Sciences and Technologies, University of 20 August 1955, Skikda 21000, Algeria

Research Focus & Metrics

Academic Career Length

16Years (2011-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 March 2011 in Construction and Building Materials
Verified
Journal Article
Closed access
HHH. Hebhoub
H. Hebhoub
HAH. Aoun
H. Aoun
MBM. Belachia
M. Belachia
HHH. Houari
H. Houari
EGElhem Ghorbel
Elhem Ghorbel

3 December 2024 in Buildings
Verified
Journal Article
Open access
PDF file
RBRahima Baghloul
Rahima Baghloul
Laidi BabouriLaidi Babouri
Laidi Babouri
HHHouria Hebhoub
Houria Hebhoub
FBFouad Boukhelf
Fouad Boukhelf
YMYassine El Mendili
Yassine El Mendili
The quarrying and utilization of natural stones such as marble and granite are growing rapidly in developing countries. However, the processing, cutting, sizing, and shaping of these stones to render them functional generates huge quantities of waste and dust. These materials are often disposed of openly in the environment, and their potentially hazardous nature has negative repercussions on both the environment and human health. In this study, marble waste (MW) was used as a filler in the unsaturated polyester resin (UPR) matrix to enhance performance and characteristics while adding value to the waste and minimizing manufacturing costs. For this purpose, samples of UPR/MW composites were produced with 0, 5, 10, 15, and 20 wt.% of MW incorporated into the UPR. A full characterization that focused on the microstructure, thermal stability, and physical and mechanical properties was carried out. The results revealed that the use of 10 to 15% of MW improves mechanical performance, with increases from 17 to 26 kJ/m2, 14 to 17 MPa, and 794 to 1522 GPa in impact strength, tensile strength, and elastic modulus, respectively. By introducing a 20% MW filler, the composite loses its performance, particularly Shore D hardness, and becomes very brittle. Thermogravimetric analysis (TGA) indicated significant thermal stabilization, with a delay in the start decomposition temperature of 28 °C for 20 UPR/MW compared to 0 UPR/MW. Additionally, morphological and microstructural tests, namely, FT-IR, XRD, and SEM analysis, show a microstructural change, including the formation of crystalline phases, enhancing matrix-filler interactions due to the creation of Mg-O and Ca-O chemical bonds and the forming of filler agglomeration at high introduction rates that lead to defects in the microstructure. These results confirmed the mechanical results of the UPR/MW composites.

25 February 2014 in STRUCTURAL ENGINEERING AND MECHANICS
Verified
Journal Article
Closed access
HHH. Hebhoub
H. Hebhoub
MBM. Belachia
M. Belachia
RDR. Djebien
R. Djebien

25 March 2015 in STRUCTURAL ENGINEERING AND MECHANICS
Verified
Journal Article
Closed access
RDR. Djebien
R. Djebien
MBM. Belachia
M. Belachia
HHH. Hebhoub
H. Hebhoub

8 November 2018 in IOP Conference Series: Materials Science and Engineering
Verified
Conference Paper
Open access
PDF file
MBM Belachia
M Belachia
HHH Hebhoub
H Hebhoub
The building materials manufacturing industry generates a lot of waste and their landfill has many problems (including the place occupied by the storage sites, the importance of the costs and the impact on the environment). This industry does not pose problems only at the end of the life cycle of these materials. It is imperative to find means of recovery and reuse of these wastes and therefore to propose another alternative to the depletion of aggregate sources. The main objective of this study is to show technically the possibility of using the aggregates from the manufacture of marble as a substitute in hydraulic concrete. The article presents the methodology of study and characterization of marble scrap, as well as the different formulations of concretes; series of tests have been developed, with a constant W / C ratio for a variable recycled aggregate content. The study consists of analyzing the results obtained and its comparison with a control concrete (100% natural aggregates); the rheological properties in the fresh and mechanically hardened state of concretes with different proportions of aggregates from marble waste (25%, 50%, 75%, 100%). The results show that marble waste is ready to be used as substitute material.

1 January 2017 in Journal of Applied Engineering Science
Verified
Journal Article
Closed access
PDF file
SBSaid Berdoudi
Said Berdoudi
HHH. Hebhoub
H. Hebhoub
RDR. Djebien
R. Djebien
The management of mining waste is one of the major environmental problems which are facing the mining professionals, during their activity and even after the closure of the mine. Indeed, excavated materials from mines belong to a category of waste, and especially when dealing with an open pit, are generally left on the surface. In this experimental study, the utilization of sand waste marble dust as an additive in cement production has been investigated. The aggregate used in this study is a sand of marble wastes (excess loads of sand exposed to bad weather conditions) of the derived marble quarry from Fil-fila (Skikda, east of Algeria). The study focuses the effect of marble waste sand fillers substitution in the cement paste and mortar (5, 10, 15 and 20℅) with a finesse greater than that of cement, to compare the results obtained through control samples (0%) of cement paste properties in the fresh condition and the mechanical performances of mortar in the hardened condition. The obtained results show that the sand marble wastes fillers can be technically used as additive in cement. Therefore, it can be possible to prevent the environmental pollution especially in this region with excessive marble production and to well manage natural resources.