Azira Muratovna Yermakhanova

Azira Muratovna Yermakhanova

Auto-generated profile, based on publicly available information

Azira Muratovna Yermakhanova


Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
15 December 2019 in Kompleksnoe Ispolzovanie Mineralnogo Syra = Complex Use of Mineral Resources
Verified
Journal Article
Closed access
NJNational Centre for space research and technology” JSC
National Centre for space research and technology” JSC
LMLaura Mustafa
Laura Mustafa
MIM.B. Ismailov
M.B. Ismailov
AYA.M. Yermakhanova
A.M. Yermakhanova
“J“National Centre for space research and technology” JSC
“National Centre for space research and technology” JSC
DHDnipro National University» named after Oles Honchar
Dnipro National University» named after Oles Honchar
Increasing strength of epoxide resin (ER) and carbon fiber reinforced plastic (CFRP) is an aim up-to-date for many machinery sections: space, aviation, defense, automotive, and others. The aim is achieved via numerous methods of ER and carbon fiber reinforced plastic modifications. ER modifications is carried through injection of various chemical compounds. One of efficient modifications assumes introduction of plasticizers (tricresyl phosphate, oleic acid) or thermoplastics (polysulfone, polycarbonate, polystyrene, high impact polystyrene). The article contains experimental data of various types of modifiers influence on strength of ER and CFRP available in literature. The mechanism of modifying ER and CFRP with plasticizers and thermoplastics were analyzed. The introduction of plasticizers as ER modifiers leads to a twofold improvement in impact strength. The optimal input of plasticizers in ER is 15% and depends on the completeness of solubility in the binder, a further increase in the input of plasticizer leads to a decrease in the strength of the material. Modification of thermoplastics with CFRP can lead to an improvement in compression strength by 20% and impact strength by 2 times. With the introduction of thermoplastics over 20% in CFRP, strength indicators are reduced. The acquired data is necessary to elaborate domestic technology for production of high-impact CFRP.

2 May 2022 in Kompleksnoe Ispolzovanie Mineralnogo Syra = Complex Use of Mineral Resources
Verified
Journal Article
Closed access
AYA.M. Yermakhanova
A.M. Yermakhanova
ASA.F. Sanin
A.F. Sanin
Mohammed MeiirbekovMohammed Meiirbekov
Mohammed Meiirbekov
BBB.M. Baiserikov
B.M. Baiserikov
Currently, the production and use of military UAVs in the direction of robotic complexes is actively developing. The purpose and use of military UAVs differ from civilian ones, based on two functions: reconnaissance purpose and a carrier of a warhead. The specifics of military UAVs are their invisibility to enemy radars and ensuring stable transmission of information from the command post. For these purposes, first of all, the UAV material must have the properties of radio transparency. For the production of UAV hulls, power elements, high-strength PCM are needed, which include organoplastics, carbon fiber, fiber glass. The choice of materials for parts of components and assemblies of aviation equipment depends on their operating conditions: operating loads, material properties. Organoplastics (OP) fully meets these requirements among polymer composite materials (PCM). OP have high strength properties along with low dielectric losses (radio transparency) compared to other fiber composites. This paper presents an overview of studies of dielectric and strength properties, as well as ways to improve the mechanical properties of organoplastics. The analysis of the work has shown that for radiotransparent organoplasty, the optimal frequency range of permittivity is 1kHz-12 GHz. The ultimate strength of organoplastics varies in the range from 320 MPa to 1 GPa. The possibilities of increasing the strength of aramid fibers and ways of modifying organoplastics epoxy resins are considered.

22 November 2018
Verified
Conference Paper
Closed access
AYAzira Muratovna Yermakhanova
Azira Muratovna Yermakhanova
MIMarat Bazaralievich Ismailov
Marat Bazaralievich Ismailov
The effect of carbon nanotubes on the elastic-strength properties of epoxy resin and carbon plastic was investigated. The epoxy resin in the form of Etal Inject-T compound, Sigratex KDK carbon fabric,Taunit-M carbon nanotubes conditionally named as CNT-1, as well as functionalized (modified) variety of them by grafting to the surface of new chemical groups: carboxylated - CNT-2, carboxyl-hydroxylated - CNT-3, amidated - CNT-4 were used in the work. The injection of CNT - 1 into epoxy resin or carbon fiber reinforced plastic did not produce the hardening. At a strain rate of up to 20 mm/min, the epoxy resin with CNT-2-4 consisting of three zones, practically does not affect the elastic zone, but it strengthens the plastic and elastic-plastic zones. It is established that at the strain rate ≥ 20 mm/min the three-zone structure of the epoxy resin passes into a single-zone deformation with parameters σy = 110.5 MPa, εy = 5.05%, E = 2.15 GPa. Under the same conditions of the rate of deformation of carbon fiber reinforced plastic, zones of elastic, elastic-plastic and pseudoelastic deformation are observed. With an increase in the strain rate of 20 mm/min, the single-zone pseudoelastic deformation is characterized by the parameters σs = 425 MPa, εs= 2.3%, Eef = 19.3 GPa. The injection of carbon nanotubes CNT-2-4 into carbon fiber reinforced plastic increased the compressive strength by CNT-2 - 6% of CNT-3 - 12%, CNT-4 - 17%, modulus of elasticity by 13-20%.

30 December 2024 in Science and Technology of Kazakhstan
Verified
Journal Article
Closed access
АЕА. М. Ермаханова
А. М. Ермаханова
МММ. Н. Мейірбеков
М. Н. Мейірбеков
БББ. М. Байсериков
Б. М. Байсериков
НБН. Б. Богуспаев
Н. Б. Богуспаев
Ұшқышсыз ұшу аппараттары (ҰҰА) соңғы жылдары экономика, қорғаныс және ғылыми зерттеулерді қоса алғанда, әртүрлі салаларда бірегей мүмкіндіктері мен әртүрлі қолданбалары үшін кең танымалдылыққа ие болды. Дегенмен, олардың функционалдығы ұшу автономиясы және жердегі станциямен байланыс сияқты бірқатар факторлармен шектеледі. Осы аспектілерді жақсартудың негізгі шешімдерінің бірі - ҰҰА конструкцияларында радиомөлдір материалдарды пайдалану. Төмен диэлектрлік және жоғары радиомөлдірлігі бар полимерлі композиттер заманауи телекоммуникациялық технологияларда шешуші рөл атқарады, бұл сигналдың жоғары жылдамдығын және құрылғылардың жоғары интеграциясын қамтамасыз етеді. Алайда, қажетті сипаттамалары бар осындай диэлектрлік полимерлі композиттерді құру терең талдау мен эксперименттерді қажет ететін күрделі міндет болып табылады. Бұл жұмыста арамидті-эпоксидті композит, шыны талшық, көміртекті пластик және жоғары тығыздықтағы ультра жоғары молекулалық полиэтилен сияқты әртүрлі композиттік материалдардың диэлектрлік жоғалуы мен радиолық мөлдірлігін зерттеудің салыстырмалы нәтижелері келтірілген. Бұл жұмыста эксперименттер көрсеткендей, бұл материалдардың өткізгіштік пайызы әр түрлі: көміртекті пластик (КП) тек 2,45 % құрайды, ал арамид-эпоксидті композит (AEK) 79,43 %, өте жоғары молекулалы тығыздығы жоғары полиэтилен (ЖМЖТП)) 80,16 %, ал шыны талшық (ШТ) 78,88 % көрсетеді. КП-тегі диэлектрлік шығынның тангенс бұрышы басқа композиттерге қарағанда едәуір жоғары, бұл оның тиімділігінің төмендігін көрсетеді. Сонымен қатар, ЖМЖТП тангенс бұрышының ең кіші мәндерін көрсетеді, ал АЭК және шыны талшықтар тұрақты және төмен диэлектрлік шығынға ие, бұл оларды жоғары жиілікті құрылғылар мен байланыс жүйелерінде қолдануға перспективалы етеді. Кілтті сөздер: полимерлі композициялық материал, диэлектрлік жоғалту, радиомөлдірлік, жиілік, тангенс бұрышы.