Seok-Bong Hyun

Seok-Bong Hyun

Auto-generated profile, based on publicly available information

Seok-Bong Hyun

Communication RF Research Section Electronics and Telecommunications Research Institute (ETRI) 218 Gajeong‐ro, Yuseong‐gu Daejeon 34129 South Korea

Research Focus & Metrics

Academic Career Length

23Years (2004-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
4 March 2019 in IEEE Transactions on Antennas and Propagation
Verified
Journal Article
Closed access
GBGrzegorz Bogdan
Grzegorz Bogdan
KGKonrad Godziszewski
Konrad Godziszewski
Yevhen YashchyshynYevhen Yashchyshyn
Yevhen Yashchyshyn
CKCheol Ho Kim
Cheol Ho Kim
SHSeok-Bong Hyun
Seok-Bong Hyun
This paper presents a design of a time modulated antenna array (TMAA) with substantially wider bandwidth and higher efficiency than have been already presented in the literature. The TMAA is designed for 5.4–5.8 GHz frequency band. More than 50 MHz of channel bandwidth is achieved by utilization of ultra fast microwave switches, digital delay lines with 60 ps step, and fast control circuitry. The efficiency is improved by alternate switching between array elements instead of switching between the array element and a matched load. Moreover, a mathematical derivation of optimal switching sequence is given. The beam-steering at the first sideband frequency was obtained with a 1 degree step in a range from –50 to 50 degrees. The TMAA has been evaluated by means of the radiation pattern measurements at different sideband frequencies.

15 June 2004 in ETRI Journal
Verified
Journal Article
Open access
PDF file
SHSeok-Bong Hyun
Seok-Bong Hyun
GTGeum-Young Tak
Geum-Young Tak
SKSun-Hee Kim
Sun-Hee Kim
BKByung-Jo Kim
Byung-Jo Kim
JKJinho Ko
Jinho Ko
SPSeong-Su Park
Seong-Su Park
This paper reports on our development of a dual-mode transceiver for a CMOS high-rate Bluetooth system-on-chip solution. The transceiver includes most of the radio building blocks such as an active complex filter, a Gaussian frequency shift keying (GFSK) demodulator, a variable gain amplifier (VGA), a dc offset cancellation circuit, a quadrature local oscillator (LO) generator, and an RF front-end. It is designed for both the normal-rate Bluetooth with an instantaneous bit rate of 1 Mb/s and the high-rate Bluetooth of up to 12 Mb/s. The receiver employs a dualconversion combined with a baseband dual-path architecture for resolving many problems such as flicker noise, dc offset, and power consumption of the dual-mode system. The transceiver requires none of the external image-rejection and intermediate frequency (IF) channel filters by using an LO of 1.6 GHz and the fifth order on-chip filters. The chip is fabricated on a 6.5-mm2 die using a standard 0.25-μm CMOS technology. Experimental results show an in-band image-rejection ratio of 40 dB, an IIP3 of −5 dBm, and a sensitivity of −77 dBm for the Bluetooth mode when the losses from the external components are compensated. It consumes 42 mA in receive π/4-diffrential quadrature phase-shift keying (π/4-DQPSK) mode of 8 Mb/s, 35 mA in receive GFSK mode of 1 Mb/s, and 32 mA in transmit mode from a 2.5-V supply. These results indicate that the architecture and circuits are adaptable to the implementation of a low-cost, multi-mode, high-speed wireless personal area network.

4 December 2009 in ETRI Journal
Verified
Journal Article
Open access
PDF file
BMByung-Hun Min
Byung-Hun Min
SHSeok-Bong Hyun
Seok-Bong Hyun
HYHyun-Kyu Yu
Hyun-Kyu Yu
This paper presents a switched self-biasing and a tail current-shaping technique to suppress the 1/f noise from a tail current source in differential cross-coupled inductance-capacitance (LC) voltage-controlled oscillators (VCOs). The proposed LC VCO has an amplitude control characteristic due to the creation of negative feedback for the oscillation waveform amplitude. It is fabricated using a 0.13 µm CMOS process. The measured phase noise is -117 dBc/Hz at a 1 MHz offset from a 4.85 GHz carrier frequency, while it draws 6.5 mA from a 0.6 V supply voltage. For frequency tuning, process variation, and temperature change, the amplitude change rate of the oscillation waveform in the proposed VCO is 2.1 to 3.2 times smaller than that of an existing VCO with a fixed bias. The measured amplitude change rate of the oscillation waveform for frequency tuning from 4.55 GHz to 5.04 GHz is 131 pV/Hz.

11 September 2020 in Advanced Electronic Materials
Verified
Journal Article
Closed access
PDF file
JHJae Hur
Jae Hur
INIn‐Joong Nam
In‐Joong Nam
YCYoung‐Kyun Cho
Young‐Kyun Cho
DKDa‐Jin Kim
Da‐Jin Kim
EJEon‐Seok Jo
Eon‐Seok Jo
YCYang-Kyu Choi
Yang-Kyu Choi

18 March 2020 in Electronics
Verified
Journal Article
Open access
PDF file
Young-Kyun ChoYoung-Kyun Cho
Young-Kyun Cho
BPBong Hyuk Park
Bong Hyuk Park
SHSeok-Bong Hyun
Seok-Bong Hyun
The switching noise and conversion efficiency of step-up DC-DC converters need to be improved to meet increasing demand. The delta-sigma modulation (DSM) technique is typically used to improve the performance of buck converters; however, this control scheme is not directly applicable for boost converters. This paper presents a boost DC–DC converter using a continuous-time delta-sigma modulator (DSM) controller for battery-powered and noise-sensitive applications. The proposed converter can adjust a wide range of output voltages dynamically by clamping the maximum duty cycle of the DSM, thus enabling stable and robust transient responses of the converter. The switching harmonics in the converter output are reduced effectively by the noise shaping property of the modulator. Moreover, the converter does not suffer from instability of mode switching due to the use of a fixed third-order DSM. Fabricated in a 180 nm CMOS, the converter occupies an active area of 0.76 mm2. It produced an output voltage ranging from 2.5 V to 5.0 V at an input voltage of 2.0 V and achieved a peak conversion efficiency of 95.5%. The output voltage ripples were maintained under 25 mV for all load conditions. A low noise output spectrum with a first spurious peak located −91 dBc from the signal was achieved.

14 October 2005 in ETRI Journal
Verified
Journal Article
Open access
PDF file
BCByoung Gun Choi
Byoung Gun Choi
SHSeok-Bong Hyun
Seok-Bong Hyun
GTGeum-Young Tak
Geum-Young Tak
HLHee-Tae Lee
Hee-Tae Lee
SPSeong-Su Park
Seong-Su Park
CPChul Soon Park
Chul Soon Park
A CMOS direct-conversion mixer with a single transistor-level topology is proposed in this paper. Since the single transistor-level topology needs smaller supply voltage than the conventional Gilbert-cell topology, the proposed mixer structure is suitable for a low power and highly integrated RF system-on-a-chip (SoC). The proposed direct-conversion mixer is designed for the multi-band ultra-wideband (UWB) system covering from 3 to 7 GHz. The conversion gain and input P1dB of the mixer are about 3 dB and −10 dBm, respectively, with multi-band RF signals. The mixer consumes 4.3 mA under a 1.8 V supply voltage.