WO 3 -based gas sensors have attracted the attention of researchers around the world in creating and developing sensors that are sensitive, stable, and have excellent reproducibility against harmful gases. Various studies that have been performed since the last few years exhibited the superior potential of WO 3 in carrying out optimal chemisorption of oxidizing and reducing gas molecules. The additional materials such as metal, metal oxide, and carbon nanomaterial can significantly widen the active state area of the WO 3 surface and other facts in various studies illustrate that the addition of polymers will change the characteristics of the semiconductor sensor. This review provides a comprehensive review of the development and modification of WO 3 for enhancing toxic gas sensor performances. In addition, the discussion of the sensing mechanism, future opportunities as well as challenges will be addressed thereby can inspire research progress on WO 3 -based toxic gas detection sensors.
6 January 2021 in Journal of the Electrochemical Society
Magnetite (Fe 3 O 4 ) nanostructures and their modifications with other materials show proper characteristics to be implemented as a sensing material. This paper provides a brief review of the application of the Fe 3 O 4 nanostructures and their modifications as sensitive material for pollutant gas sensors. Several studies were highlighted to explain the past-to-present progress of materials development. Various synthesis procedures of the materials were also clearly explained. The application of pure Fe 3 O 4 nanostructures and their modification as sensitive materials in gas sensor devices to detect toxic gases is the main section of this paper. Last, the future prospects section summarized the materials’ development and provided a suggestion for future development.
The Tl2-xTexBa2CaCu2O8-δ (Tl-2212) high temperature superconductors with x = 0.0-0.5 have been prepared by the standard solid-state reaction method. The precursor powder were sintered at 900°C for 24 h with several grindings and heating. The powder were then pressed into pellets and heated at 910°C in oxygen flow for 4 min followed by furnace cooling. The electrical resistance versus temperature dependence measurements showed metallic normal state behavior for all samples. Substitution of Te at the Tl-site led to multi-phasic samples. The x = 0.4 sample showed the highestTc zero= 98 K and Tconset= 111K. The Tl-2212 phase increased from 50% for x=0 up to 92% in the x= 0.4 sample.
1 January 2025 in Environment and Natural Resources Journal
This study was conducted to investigate the synthesis of magnetite nanoparticles from iron sand collected from the Bah Bolon River in Indonesia, using the coprecipitation method with NaOH and NH4OH as precipitants. The results showed that based on SEM-EDX (scanning electron microscopy coupled with energy-dispersive x-ray spectroscopy) analysis, the Fe content of the raw iron sand, initially at 34.76%, increased to 45.50% following synthesis with NH4OH, indicating enhanced purity in the final product. SEM observations found average particle sizes of approximately 53 nm for nanoparticles synthesized with NaOH and 20 nm for those synthesized with NH4OH. X-ray diffraction (XRD) analysis confirmed that the synthesized nanoparticles retain the magnetite (Fe3O4) phase with a face-centered cubic (FCC) spinel structure. Crystallite size calculations using the Scherrer equation yielded average crystallite sizes of 80.194 nm for NaOH-synthesized samples and 15.124 nm for NH4OH-synthesized samples, demonstrating that NH4OH favors the formation of smaller crystallites. Lattice strain analysis through the Williamson-Hall method showed positive tensile strain values for all samples, indicating structural tension within the crystal lattice. The NH4OH-synthesized nanoparticles had slightly higher lattice strain, suggesting that synthesis conditions impact both crystallite size and lattice tension. In conclusion, this study demonstrated that NH4OH was more effective than NaOH in producing high-purity, small-crystallite magnetite nanoparticles from natural iron sand, with potential implications for enhanced material properties.
22 January 2024 in Science and Technology Indonesia
This study explores the effects of incorporating palm oil fuel ash (POFA) and fly ash (FA) as partial cement substitutes on the mechanical properties and characteristics of high-quality mortar, specifically Engineered Cementitious Composites (ECC). ECC mortar was fabricated by milling POFA waste and FA through a top-down method utilizing a ball mill. The resulting material was subjected to tests for slump flow, water absorption, compressive strength, and characterized through XRF, FTIR, SEM/EDX, and XRD analyses. FTIR analysis verified the existence of Si-O and Al-O groups within the composite made of POFA-FA ECC. XRF analysis of FA and POFA showed cementitious properties, with SiO2+Al2O3+Fe2O3 exceeding 50% and CaO surpassing 10%. SEM and XRD results indicated minimal cavity formation, suggesting a high compressive strength in the mortar. Particle size distribution analysis revealed prevalent particles in the 1.5×10−1 to 2.0×10−1 μm range. The compressive strength test after 28 days, incorporating 15% FA and 10% POFA, yielded the highest strength at 59.30 MPa. The water absorption values ranged from 1.25% to 2.67%, indicating that POFA-FA assists in the cement hydration process and also serves as a filler. As a result, the material’s density is very high, leading to fewer voids formed, thus reducing the trapped water, which significantly affects the mortar’s strength.