16 January 2017 in IEEE Journal of Solid-State Circuits
This paper presents a new energy-efficient ring oscillator collapse-based comparator, named edge-pursuit comparator (EPC). This comparator automatically adjusts the performance by changing the comparison energy according to its input difference without any control, eliminating unnecessary energy spent on coarse comparisons. Furthermore, a detailed analysis of the EPC in the phase domain shows improved energy efficiency over conventional comparators even without energy scaling, and wider resolution tuning capability with small load capacitance and area. The EPC is used in a successive-approximation-register analog-to-digital converter (SAR ADC) design, which supplements a 10 b differential coarse capacitive digital-to-analog converter (CDAC) with a 5 b common-mode CDAC. This offers an additional 5 b of resolution with common mode to differential gain tuning that improves linearity by reducing the effect of switch parasitic capacitance. A test chip fabricated in 40 nm CMOS shows 74.12 dB signal-to-noise and distortion ratio and 173.4 dB Schreier Figure-of-Merit. With the full ADC consuming 1.17 μW, the comparator consumes 104 nW, which is only 8.9% of the full ADC power, proving the comparator's energy efficiency.
18 March 2024 in IEEE Transactions on Circuits and Systems II: Express Briefs
This paper presents a redundant-transition-free low-power flip-flop (FF), named contention-free change-sensing FF(C2SFF). The instability of a previous change-sensing circuit has been discovered under a test scenario where the data input change is uncorrelated with the clock signal. By resolving this instability, C2SFF is always contention-free and has low leakage, while maintaining low dynamic power by eliminating unnecessary transitions of internal clocked nodes. Without additional sizing efforts, C2SFF operates reliably down to 0.32V by removing all contention paths. Post-layout simulation results using a 65 nm CMOS process design kit show that the power consumption of C2SFF is reduced by 62.1%/52.8% with 10%/20% activity at 1V, and 56.9%/49.0% with 10%/20% activity at 0.4V, respectively, compared to transmission-gate FF (TGFF). In addition, C2SFF shows the second-best setup-hold window among tested FFs.
24 August 2020 in IEEE Journal of Solid-State Circuits
This article presents an ultra-small, high-security identification tag that is entirely built in a CMOS chip without external components. The usage of backscatter communications at 260 GHz enables full integration of a $2\,\,\times \,\, 2$ patch antenna array. For chip compactness and minimum interference caused by direct wave reflection, the backscatter signal is frequency-shifted by 2 MHz and radiated with cross polarization from the same antenna array. Such a configuration also, for the first time for RF tags, enables beamsteering for enhanced link budget. For authentication and secure wireless data transmission, the tag also integrates a compact elliptic-curve-cryptography (ECC) dedicated processor, which is based on a narrow-strong private identification protocol. The presented tag has a peak power consumption of 21 $\mu \text{W}$ and can be powered by a chip-wide array of photodiodes and a DC–DC converter. Using a low-cost 65-nm bulk CMOS technology, the terahertz (THz) ID chip has an area of only 1.6 mm 2 and demonstrates the measured downlink speed of 100 kb/s and the upload speed of 2 kb/s across 5-cm distance from the reader. The tag-reader authentication/communication protocol is fully demonstrated using external tag power and partially demonstrated using the tag-integrated photo-voltaic powering. The tag size is the smallest among all prior radio-frequency identifications (RFIDs) using far-field communications.
13 June 2023 in IEEE Transactions on Power Electronics
Owing to their high efficiency and high power density, hybrid dc–dc converters are gaining attention in academia and industry. However, no systematic procedure is currently available for creating new converter topologies where the number of inductors and capacitors is different. This articles proposes ConverGenT, an automated topological synthesis and analysis framework for two-phase hybrid dc–dc converters with one inductor and two capacitors consisting of one flying and one output capacitor. Consequently, all the converter topologies of this type are discovered. In contrast to the conventional approach that relies on intuition, this method requires less time and generates a complete set of converter topologies in a systematic manner. These two key advantages ensure that no possible converter topology is missed, making this method superior to the conventional approach. After generating a topology, all information about the converter topologies can be analyzed and verified manually or automatically, and the most suitable topology for a given application can be selected. ConverGenT has identified 62 converter families, each with a maximum of six topologies per family, that outperform conventional converters in certain aspects, with at least eight of these topologies having been published within the last five years. Details on topologies and performance of these converters are given in the Appendix.
12 April 2023 in IEEE Solid-State Circuits Letters
This letter presents a SAR temperature sensor using a clocked temperature-voltage comparator. The clocked comparator is designed to have a PTAT input offset voltage, which is quantized by SAR. Temperature transduction is spatially and temporally confined in the comparatorfs dynamic comparison. Other circuit operations are robust to the temperature changes so that the sensorfs measurement range can be maximized. Also, the sensor inherits many good aspects of a SAR ADC, such as simple design and operation, no need for complex digital filtering, and low energy consumption. As a result, the test chip fabricated in a 0.18 μm CMOS process shows a wide temperature sensing range of.50 to +130 ∘C, with a low energy consumption of 38.69 pJ/conv. After two-point calibration, the temperature sensor shows a 3-sigma temperature inaccuracy of.2.54/+2.16 ∘C.
9 July 2024 in IEEE Journal of Solid-State Circuits
This article presents an energy-efficient and easily adjustable floating-inverter amplifier (FIA), named the cyclically charged FIA (CC-FIA). Its bias point can be adjusted to a stable operating region by reusing multiple switched capacitors, which allows for enhancing current efficiency ( $g_m/I_D$ ) by setting its bias point in the near-or sub-threshold region. Easy reconfiguration of bias points enables maximizing amplifier energy efficiency across different sampling frequencies for event-driven ADC. The proposed FIA also features a stable and easily tuned open-loop gain, eliminating stability issues in closed-loop configurations and further enhancing its energy efficiency. It occupies a significantly smaller area than conventional FIAs because each reservoir capacitor pumps charge to the amplifier multiple times. The CC-FIA is implemented in a pipelined-SAR ADC as an open-loop residue amplifier and fabricated in a 65-nm CMOS process. The prototype ADC achieves an SNDR of 74.0 dB and an SFDR of 85.5 dB at a sampling frequency of 2 MS/s. The ADC consumes 72.3 $\mu$ W at a supply voltage of 1.2 V, resulting in a Schreier figure-of-merit of 175.4 dB.