Minseob Shim

Minseob Shim

Auto-generated profile, based on publicly available information

Minseob Shim

Department of Electronic Engineering, Gyeongsang National University, Jinju, South Korea

Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
16 January 2017 in IEEE Journal of Solid-State Circuits
Verified
Journal Article
Closed access
MSMinseob Shim
Minseob Shim
SJSeokhyeon Jeong
Seokhyeon Jeong
PMPaul D. Myers
Paul D. Myers
SBSuyoung Bang
Suyoung Bang
JSJunhua Shen
Junhua Shen
WJWanyeong Jung
Wanyeong Jung
This paper presents a new energy-efficient ring oscillator collapse-based comparator, named edge-pursuit comparator (EPC). This comparator automatically adjusts the performance by changing the comparison energy according to its input difference without any control, eliminating unnecessary energy spent on coarse comparisons. Furthermore, a detailed analysis of the EPC in the phase domain shows improved energy efficiency over conventional comparators even without energy scaling, and wider resolution tuning capability with small load capacitance and area. The EPC is used in a successive-approximation-register analog-to-digital converter (SAR ADC) design, which supplements a 10 b differential coarse capacitive digital-to-analog converter (CDAC) with a 5 b common-mode CDAC. This offers an additional 5 b of resolution with common mode to differential gain tuning that improves linearity by reducing the effect of switch parasitic capacitance. A test chip fabricated in 40 nm CMOS shows 74.12 dB signal-to-noise and distortion ratio and 173.4 dB Schreier Figure-of-Merit. With the full ADC consuming 1.17 μW, the comparator consumes 104 nW, which is only 8.9% of the full ADC power, proving the comparator's energy efficiency.

18 October 2019 in IEEE Journal of Solid-State Circuits
Verified
Journal Article
Closed access
IPInho Park
Inho Park
JMJunyoung Maeng
Junyoung Maeng
MSMinseob Shim
Minseob Shim
JJJunwon Jeong
Junwon Jeong
CKChulwoo Kim
Chulwoo Kim

18 April 2019 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
JJJunwon Jeong
Junwon Jeong
MSMinseob Shim
Minseob Shim
JMJunyoung Maeng
Junyoung Maeng
IPInho Park
Inho Park
CKChulwoo Kim
Chulwoo Kim
A high-efficiency charger for low-power thermoelectric energy harvesting with a method for improving the efficiency, which is called the adaptive input ripple (AIR) maximum power point tracking (MPPT) technique, is introduced in this paper. On the basis of the key finding that the end-to-end efficiency $(\eta_{E-E})$ is highly dependent on the amplitude of the input ripple of the charger ( $\Delta V_{IN}$ ) in the low-power region, the proposed AIR MPPT technique adjusts $\Delta V_{IN}$ to maximize $\eta_{E-E}$ . Moreover, the minimum input power that allows the charger to maintain operation is enhanced by the proposed AIR MPPT technique. The proposed charger is implemented with 180-nm CMOS technology. An improvement of 21% in $\eta_{E-E}$ is achieved with the proposed technique. Furthermore, the proposed technique enhances the minimum power by 7.5 μW. The startup power and minimum power of the prototype are 37 and 6 μW, respectively. The maximum $\eta_{E-E}$ is 82%.

12 August 2020 in IEEE Journal of Solid-State Circuits
Verified
Journal Article
Closed access
JMJunyoung Maeng
Junyoung Maeng
IPInho Park
Inho Park
MSMinseob Shim
Minseob Shim
JJJunwon Jeong
Junwon Jeong
CKChulwoo Kim
Chulwoo Kim
This article presents a high-voltage (HV) dual-input buck converter with a bidirectional inductor current (IL) and a fully integrated maximum power point tracking circuit for triboelectric (TE) energy-harvesting applications. The proposed converter regulates HV inputs through a single shared inductor, and HV inputs can be isolated without using an additional HV protection circuit. In addition, the proposed diode-based HV sampling circuit can accomplish high ac voltage sampling and peak detection to perform the fractional open-circuit voltage method without any external components. Fabricated using a 180-nm bipolar-CMOS-DMOS (BCD) process, the proposed system with a self-manufactured polytetrafluroethylene (PTFE)-based TE nanogenerator can regulate two HV inputs up to 70 V and achieve a power conversion efficiency of 84.7% and an end-to-end efficiency of 75.6%, which are 30.2% and 22.7% better than prior work, respectively.

26 June 2023 in IEEE Transactions on Industrial Electronics
Verified
Journal Article
Closed access
JMJunyoung Maeng
Junyoung Maeng
JJJunwon Jeong
Junwon Jeong
IPInho Park
Inho Park
MSMinseob Shim
Minseob Shim
CKChulwoo Kim
Chulwoo Kim
This letter introduces a maximum power point tracking (MPPT) technique for photovoltaic (PV) energy harvesting (EH) systems to enhance the end-to-end efficiency ( η E-E ) when the output power of PV cell ( P PV,MAX ) is low. A ripple-based PV cell current sensing and a time-domain multiplication are proposed to monitor the PV cell power delivered to the charger, which reduces the controller power consumption ( P CTR ). The PV EH system with the proposed MPPT method is implemented in a 180-nm CMOS process. The P CTR is 1.34 μ W. The measured η E-E at low P PV,MAX (13 μ W) is 88%. The measured peak η E-E is 94.4% at 82 μ W.

3 September 2019 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
JJJunwon Jeong
Junwon Jeong
MSMinseob Shim
Minseob Shim
JMJunyoung Maeng
Junyoung Maeng
IPInho Park
Inho Park
CKChulwoo Kim
Chulwoo Kim
A high-efficiency multi-charger system for photovoltaic energy harvesting is presented in this letter. The multi-charger system is widely used for module-integrated converts to offer a good anti-partial shading property. The proposed efficiency-aware cooperative control enhances the total power conversion efficiency of the system ( $\eta_{\text{TOT}}$ ) by making chargers help each other when there is a difference between the input powers to each charger due to the partial shading. The system is implemented using a 0.5-μm CMOS technology. The $\eta_{\text{TOT}}$ and the power range (for $\eta_{\text{TOT}}$ > 80%) are improved by 14% (power difference = 1.082W) and 0.61 W (lower photovoltaic cell power = 43 mW), respectively.