28 May 2026 in Strength of Materials and Theory of Structures
A comparative analysis of the optimal starting mode of the tower crane slewing mechanism in terms of speed under asymmetric (task 1) and symmetric (task 2) constraints on optimal control is presented in a scientific article. A two-mass dynamic model was used for the research, whose motion in time is described by a system of two second-order differential equations. In the course of further research, the system of two second-order differential equations was reduced to a single fourth-order differential equation. After performing the appropriate transformations, the fourth-order differential equation was presented in Cauchy form and the initial and final conditions of motion were given, under which the load oscillations will be eliminated after the turning mechanism reaches a steady speed.The optimisation task itself was reduced to the task of unconditional minimisation of a complex integral-terminal functional, where the terminal component is responsible for the fulfilment of the final boundary conditions, and the integral component is responsible for the speed of the mechanism. A series of 54 experimental studies (27 for each of the tasks under investigation) was planned, in which the independent factors were the length of the flexible suspension (which was 10, 15 and 20 metres), the load projection (which was 5, 15 and 20 m), and the load mass (which was 500, 2000 and 5000 kg).During the theoretical studies, the main assessment was carried out according to the following indicators: the duration of the system acceleration to the steady-state speed value; the maximum deviation of the flexible suspension of the load from the vertical; the maximum and root mean square values of the power in the drive and the acceleration of the load.The results of the analysis showed that when using asymmetric constraints for optimal control (task 1), the acceleration time of the studied system to a steady state speed increases compared to symmetric constraints (task 2) in the range from 1.23 to 15. 28 %, and the maximum values of kinematic characteristics decrease from 5.46 to 42.85 % and energy indicators from 0.48 to 27.83 %.
28 November 2024 in Bulletin of the National Technical University «KhPI». Series: Automobile and Tractor Construction
The article presents a comparative analysis of the kinematic and dynamic characteristics of the transient start-up mode of the trolley movement mechanism of a tower crane. The single and double mathematical pendulums effects are stressed. The study was carried out using parameters corresponding to the physical model of the tower crane boom system, which is located in the laboratory of machine dynamics of the Department of Machine and Equipment Design of NULES of Ukraine. In the course of the comparative analysis, it was found that the use of a flexible load suspension model as single or double mathematical pendulum does not significantly affect the magnitude and the change in the force in the traction rope and the speed of the trolley. However, the model influences the phase trajectory of load pendulum oscillations. The results of theoretical and experimental studies of the deviation from the vertical of a flexible load suspension by using a single and double mathematical pendulum models were compared. It was established that during the first second of movement, the results of experimental studies of load deflections are closer to the double pendulum model. After the first second of movement, the results of experimental studies are closer to the single pendulum model.
28 May 2026 in Strength of Materials and Theory of Structures
Gripper devices with weights close to the payload weight are used when jib cranes perform installation work on complex structures. For such cases, the flexible payload suspension is represented by a double mathematical pendulum model. The paper deals with the dynamics of the slewing mechanism of a jib crane with a flexible payload suspension in the form of a double pendulum. The purpose of this study is to construct a mathematical model and perform a dynamic analysis of the jib crane slewing mechanism with a double mathematical pendulum payload suspension. The slewing mechanism is represented by a dynamic model with four degrees of freedom (4-DoF). Based on this model, a mathematical model of the jib crane slewing mechanism is constructed using Lagrange equations of the second kind, forming a system of second-order ordinary differential equations. In this model, the driving torque of the electric motor is described by its dynamic mechanical characteristic. As a result of numerical solving of the equations, the kinematic, dynamic, and energy characteristics of the jib crane slewing mechanism are determined. The study investigates the main movement of the drive mechanism, as well as high-frequency oscillations of drive elements and low-frequency oscillations of the payload and gripper on the flexible suspensionIt is revealed that the dynamics of the slewing mechanism depend on the nature of the driving torque change, while low-frequency oscillations of the payload and gripper practically do not dampen and continue throughout the entire movement cycle. To reduce dynamic loads and high-frequency vibrations in the drive transmission mechanism, as well as low-frequency vibrations of the gripping device and load on a flexible suspension, it is recommended to select modes of smooth change of the drive torque during start-up and braking, which ensure the desired movement of the load on a flexible suspension.