14 December 2017 in IEEE Transactions on Sustainable Energy
Recently researchers have focused on the optimal operation of droop-controlled islanded microgrids (DCIMG). However, most of the papers consider only the economic objective. But, with increasing focus on environmental compliance, it has also become necessary to reduce emission from generation activities. Furthermore, most of the previous papers do not consider the heat demand in the microgrid and the uncertainties involved in load and renewable generation forecasting. This paper bridges all these gap areas by presenting a method for determining optimal droop settings of dispatchable distributed generation units in a DCIMG. The objectives are to minimize the operational cost and minimize the emission in the islanded droop-controlled microgrid while meeting all the operational constraints. The proposed formulation takes into account the electricity demand, the heat demand, load uncertainties, and renewable power uncertainties in the microgrid. Load and renewable power uncertainties are modeled by a stochastic scenario based approach. The multiobjective optimization problem is solved using fuzzified particle swarm optimization. The proposed method is validated on a 33-bus DCIMG test system. The results show the effectiveness of the proposed method.
1 June 2017 in Sustainable Energy Technologies and Assessments
27 March 2019 in IET Generation, Transmission & Distribution
An AC–DC hybrid microgrid is gradually becoming popular. For economic viability and environmental sustainability, an AC–DC microgrid should be operated optimally. This study introduces an optimal power dispatch strategy for simultaneous reduction of cost and emission from generation activities in an AC–DC hybrid microgrid under load and generation uncertainties. The operational attributes of an AC–DC hybrid microgrid, and load and renewable generation uncertainties are incorporated in the optimal scheduling problem by using a customised power‐flow technique, and by modelling uncertainties by Hong's two‐point estimate method, respectively. The economic and environmental objectives are modelled in the fuzzy domain by fuzzy membership functions. A combination of particle swarm optimisation and fuzzy max–min technique is then employed for obtaining the optimal solution. The static active power droop constants of the dispatchable units are the control variables. Simulation results on a 6‐bus AC–DC hybrid microgrid system demonstrate that optimal scheduling results in 4.26% reduction of operating cost and 13.91% reduction of emission in comparison to capacity based droop settings. Further, a comparison between the proposed method and the elitist multi‐objective GA indicates that the optimised solution lies on the Pareto‐front, thereby validating the proposed technique.
4 May 2018 in IET Generation, Transmission & Distribution
This study presents a method for determining optimal droop settings of dispatchable distributed generation units in a droop‐controlled microgrid (DCMG). The objectives are to (i) minimise the operational cost and (ii) minimise the emission in the DCMG while meeting all the operational constraints. The proposed formulation takes into account the electricity demand, load uncertainties and renewable power uncertainties in the MG. Load and renewable power uncertainties are modelled by Hong's point estimate method. The bi‐objective optimisation problem is solved using fuzzified particle swarm optimisation. The proposed method is validated on a 6‐bus DCMG test system. The results show the effectiveness of the proposed method.
17 May 2018 in IEEE Transactions on Sustainable Energy
This paper proposes a method to determine optimal droop values of dispatchable distributed generation (DG) units in an islanded droop-controlled DC microgrid. Objectives are to minimize fuel cost and maximize small signal stability of the system. In this paper, a detailed state space model of an islanded droop-controlled DC microgrid including the converter, network parameters, and network interconnection is developed. The developed model is then used to obtain the dominant eigen value of the system. Particle swarm optimization is used to determine the optimal droop values of the dispatchable DG units in order to simultaneously reduce the fuel cost, increase system damping, and push the most dominant eigen value away from the imaginary axis to the left of the s-plane. The bi-objective optimization is solved using a fuzzy max-min based approach. The proposed method is validated on a sample 3-bus droopcontrolled DCMG test system. Comparison of the result obtained by the fuzzy max-min approach with that of NSGA-II is also presented in this paper.
1 June 2020 in Engineering with Computers