3 April 2017 in Experiments in Fluids
28 April 2017 in Journal of Fluids Engineering
The control of flow in the wake of a circular cylinder by an attached permeable plate having various porosity ratios was analyzed experimentally using both particle image velocimetry (PIV) and dye visualization techniques. The force measurements were also done in order to interpret the effect of control method on drag coefficient. The diameter of the cylinder and length to diameter ratio of the plate were kept constant as D = 50 mm and L/D = 1.0, respectively. The porosity ratio, β, which can be defined as the ratio of open surface area to the whole body surface area, was taken as β = 0.4, 0.5, 0.6, 0.7, and 0.8 (permeable plates). The study was performed considering deep water flow conditions with a constant Reynolds number of ReD = 5000 based on the cylinder diameter. Each permeable plate was attached on the separation point and the results were compared with the results of cylinder without permeable plate (plain cylinder) in order to understand the control effect. Both qualitative and quantitative results revealed that the permeable plates of 0.4 ≤ β ≤ 0.6 are effective on controlling the unsteady flow structure downstream of the cylinder, i.e., the vortex formation length was increased, turbulent statistics was reduced and vortex shedding frequency was diminished when the permeable plate attached normal to the cylinder surface from the lower separation point. However, the drag force acting on the cylinder was found to be increased due to the increased cross-sectional area.
10 October 2019 in Experiments in Fluids
1 February 2024 in Physics of Fluids
Scale-adaptive simulations (SAS) of three-dimensional flow around a circular cylinder fitted with a passive version of a novel flow control method (passive Venturi actuator, PVA) are performed at a diameter-based Reynolds number of Re = 28 000. The PVA consists of one or more narrow slits located at the top and/or bottom sides of the cylinder that connected to the throat of the axial Venturi slit in this cylinder. The main purpose of the study is to investigate the influence of divergence angle and narrow slit location relative to the axial Venturi slit on the aerodynamic performance of the cylinder. To this end, four models were designed with various PVAs. Additional models, a plain cylinder (unmodified model) and a cylinder fitted with an axial Venturi slit (model without a narrow slit), were also used for quantitative comparison. SAS predicts that an additional 5% reduction in the time-averaged drag coefficient, ⟨CD⟩, was observed when two narrow slits located on the surface at an angle of ±80° from the front stagnation line were fitted to the cylinder with an axial Venturi slit. Reducing the divergence angle of the PVA leads to improvements in ⟨CD⟩ and root mean square of fluctuating force coefficients, CD−rms and CL−rms. It is found that a cylinder with a PVA that has two narrow slits and a divergence angle of 6° can produce a 28.6% reduction in ⟨CD⟩, a 58.5% reduction in CD−rms, and an 81.2% reduction in CL−rms, when compared to the plain cylinder.
1 July 2023 in Journal of Applied Fluid Mechanics
An experimental investigation has been undertaken to determine the effects of plain and notched base flaps on the drag performance of simplified tractor-trailer combination without any intermediate gap, Generalized European Transport System (GETS). Both plain and notched base flaps are rigid, made up of three identical flaps whose length is equal to the width of the GETS model, and not angled inward or outward. The experiments examined three-sided flap configurations corresponding to various combinations of seven heights of the plain part (from 10 to 40 mm in steps of 5 mm), four notch amplitudes (from 2.5 to 10 mm in steps of 2.5 mm), and five notch wavelengths (from 10 to 50 mm in steps of 10 mm). It is shown that the drag performance of the plain flap at zero yaw highly depends on the height of the plain flap. The maximum drag reduction occurs for e/w=0.1 yielding a drag reduction of 1.9% when compared to the GETS model without flap (baseline GETS). It was shown that the time-averaged drag coefficient increased slightly until a maximum was reached at e/w=0.3 but then decreased slightly with increasing e/w. Under zero yaw angle conditions, GETS model with a notched base flap, e10-a05.0-λ20, gives the lowest drag. The addition of this base flap to the GETS model resulted in a 2.8% drag reduction. This notched base flap was shown to be more effective not only at reducing under yawed flow conditions tested but also at reducing time-averaged side coefficient under yawed flow conditions tested, compared to the e10-a00.0-λ00 flap.
1 July 2025 in Ocean Engineering