Sihoon Choi

Sihoon Choi

Auto-generated profile, based on publicly available information

Sihoon Choi

Nagoya University

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
6 August 2024 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
SCSihoon Choi
Sihoon Choi
JCJiyoon Choi
Jiyoon Choi
TWThiyu Warnakulasooriya
Thiyu Warnakulasooriya
JSJong-Won Shin
Jong-Won Shin
JIJun Imaoka
Jun Imaoka
MYMasayoshi Yamamoto
Masayoshi Yamamoto
This article proposes a novel power module configuration which replaces a part of the bottom copper layer of a direct-bonded copper by low-permittivity (low- ϵ ) epoxy. The proposed power module reduced common-mode (CM) capacitance by 52.5% compared to that of the conventional counterpart. The CM noise measured from line impedance stabilization network was reduced by 4–5 dB μ V in steady-state operation. The proposed power module does not sacrifice thermal performance which is proved by simulation and thermal resistance measurement. Thermal cycling tests confirmed high mechanical reliability with no cracks in the solder near the epoxy region. Less mechanical deformation of 5.80 μm was observed compared to the 9.48 μm of the power module that adopts air instead of low- ϵ epoxy.

17 August 2022 in IEEE Transactions on Industrial Electronics
Verified
Journal Article
Closed access
SCSihoon Choi
Sihoon Choi
JSJong-Won Shin
Jong-Won Shin
JIJun Imaoka
Jun Imaoka
MYMasayoshi Yamamoto
Masayoshi Yamamoto
This article proposes a novel voltage-controlled variable inductor (VI) for fixing the switching frequency of dc–dc converters in the critical conduction mode (CRM). It overcomes the limitations of conventional current-controlled VIs such as complex winding structures, difficulties in control, and high sensitivity to temperature. In the proposed voltage-controlled VI, the primary side inductance of a coupled inductor is regulated by an auxiliary voltage source on the secondary side. The auxiliary voltage source is implemented by an auxiliary dc–dc converter, which delivers power to the load in parallel with the main converter. The operating principle of the converter system for employing the proposed VI is presented, and a control loop is designed to fix the switching frequency, considering the small-signal model of the auxiliary converter. The validity of the proposed VI is experimentally verified using a prototype CRM boost converter with an output voltage of 400 V and a maximum power of 400 W. The switching frequency is fixed at 100 kHz and the soft switching of the main converter is maintained regardless of the input voltage and output power.

19 December 2023 in IEEE Transactions on Industry Applications
Verified
Journal Article
Closed access
SCSihoon Choi
Sihoon Choi
JIJun Imaoka
Jun Imaoka
MYMasayoshi Yamamoto
Masayoshi Yamamoto
Powder cores demonstrate soft saturation characteristics which shows gradual decrease of inductance with increase of winding current. Concentrated air gap has been utilized to suppress soft saturation by increasing effective magnetic reluctance and modifying flux cancellation in coupled inductors. However, the saturation characteristics has not been well elaborated due to the difficulty to estimate the varied saturation levels experienced by different segments of the coupled inductor. The proposed design scheme simplifies the magnetic design and presents the least number of turns with optimized air gap length, which satisfies the target inductances. The design method features good accuracy over a wide range of winding current even with large air gap. Five prototype coupled inductors with different air gap length were built to verify the proposed design scheme. They were implemented to an interleaved boost converter to prove the precision of the proposed scheme. The experimental results also revealed that the coupled inductor with the least number of turns and an optimal air gap length presents an efficiency gain of 0.7% at 1 kW and 1.36% at 1.5 kW, respectively, compared to the case with the highest number of turns.

19 August 2024 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
SCSihoon Choi
Sihoon Choi
TWThiyu Warnakulasooriya
Thiyu Warnakulasooriya
JCJiyoon Choi
Jiyoon Choi
YYYu Yonezawa
Yu Yonezawa
JIJun Imaoka
Jun Imaoka
MYMasayoshi Yamamoto
Masayoshi Yamamoto
This letter proposes a novel vertical shunt resistor and its packaging method into power modules. The proposed shunt resistor has significantly lower equivalent series inductance and thermal resistance compared to lateral counterparts. It provides a higher maximum operating temperature and power rating using a NiCr-based resistor alloy. Integrating the shunt resistor into power modules does not compromise the size, layout, or manufacturability of the power module. Two types of shunt-resistor-integrated power modules were prototyped, and guidelines to reduce variation of effective resistance and achieve a low temperature coefficient of resistance were provided.

28 June 2024 in IEEE Access
Verified
Journal Article
Open access
SCSihoon Choi
Sihoon Choi
JCJiyoon Choi
Jiyoon Choi
TWThiyu Warnakulasooriya
Thiyu Warnakulasooriya
JSJong-Won Shin
Jong-Won Shin
JIJun Imaoka
Jun Imaoka
MYMasayoshi Yamamoto
Masayoshi Yamamoto
Silicon carbide devices provide higher switching speed and switching frequency than their silicone counterpart. However, these characteristics generate significant electromagnetic interference such as common-mode (CM) noise. This paper proposes a novel power module to reduce CM noise without compromising size, thermal performance, and reliability of the power module. A specific part of the bottom copper layer of a directed-bonded copper is etched to reduce CM capacitance. Epoxy is used to increase mechanical reliability by supporting ceramic and top copper layers. This supporting epoxy also prevents an encapsulant from leaking into the etched area. Design methodologies for the proposed power module are provided in detail. Conventional and proposed power modules were prototyped and CM noise was experimentally measured with 400-V input, 200-V output, and 50-kHz switching frequency. The CM noise of the proposed power module was reduced by 5 dBμV. Thermal cycling tests were conducted to confirm the degradation of the proposed power module. Cross-sections of the power modules and measured electrical characteristics verify the reliability of the proposed power module.

3 October 2025 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
SCSihoon Choi
Sihoon Choi
JCJiyoon Choi
Jiyoon Choi
TWThiyu Warnakulasooriya
Thiyu Warnakulasooriya
JSJong-Won Shin
Jong-Won Shin
JIJun Imaoka
Jun Imaoka
MYMasayoshi Yamamoto
Masayoshi Yamamoto
The novel power module introduced in this article features an etched section of the bottom copper layer of a direct-bonded copper substrate, encapsulated in silicone gel. The proposed design improves manufacturability and reduces common-mode (CM) electromagnetic interference, while it does not sacrifice size, thermal performance, and manufacturing process. The measured CM noise in prototype hardware was decreased by maximum 5 dBμV in steady-state operation. Thermal cycling tests with a total of 1000 cycles confirmed the proposed power module does not compromise mechanical stability.