Tsung Heng Chiew

Tsung Heng Chiew

Auto-generated profile, based on publicly available information

Tsung Heng Chiew

Tunku Abdul Rahman University of Management and Technology

Research Focus & Metrics

Academic Career Length

15Years (2012-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
22 May 2017 in International Journal of Control, Automation, and Systems
Verified
Journal Article
Closed access
PDF file
CHChiew Tsung Heng
Chiew Tsung Heng
Zamberi JamaludinZamberi Jamaludin
Zamberi Jamaludin
AHAhmad Yusairi Bani Hashim
Ahmad Yusairi Bani Hashim
LALokman Abdullah
Lokman Abdullah
NRNur Aidawaty Rafan
Nur Aidawaty Rafan

1 January 2015 in Procedia CIRP
Verified
Journal Article
Open access
NRN.A. Rafan
N.A. Rafan
Zamberi JamaludinZamberi Jamaludin
Zamberi Jamaludin
TCT.H. Chiew
T.H. Chiew
LAL. Abdullah
L. Abdullah
MMM.N. Maslan
M.N. Maslan
This paper presents contouring error analysis using various classical feedforward controllers. A circular motion is performed using an XY positioning stage with specified amplitude and velocities. This study applied single Static friction model, Generalized Maxwell Slip (GMS) model and combination of both models together with feedforward Proportional-Integral-Derivative (PID) controller. Contour error in term of quadrant glitch is measured by respective angle in each quadrant of circular motion. Due to stick slip motion during velocity reversal generate glitches near zero velocity. Root-mean-square error (RMSE) is calculated based on radial error of circular motion to show variance of errors towards average. The results are experimentally shown that glitches have higher reduction in lower velocity by comparing between applied with and without friction feedforward controller. Better reduction in contour errors improves precision of machine tools and hence increases productivity

30 March 2013 in Procedia Engineering
Verified
Journal Article
Open access
PDF file
TCT.H. Chiew
T.H. Chiew
Zamberi JamaludinZamberi Jamaludin
Zamberi Jamaludin
AHA.Y. Bani Hashim
A.Y. Bani Hashim
NRN.A. Rafan
N.A. Rafan
LAL. Abdullah
L. Abdullah
This paper focuses on friction identification and numerical validation on ball-screw driven XY milling table. Two friction models namely; static friction model and Generalized Maxwell-slip (GMS) model are identified and validated numerically. Static friction model is identified by measuring the control command signals of various constant velocities while friction-position behavior during sliding and pre-sliding regimes is determined to identify GMS model. Parameters of static friction model are estimated using heuristic approach while application of piecewise linear functions and theory of superposition in virgin curve are used in approximating the parameters of GMS model. Based on obtained parameters, the models are generated in simulation using MATLAB/Simulink to verify the friction models and glitches formed during motion of low velocity. Simulation results showed that GMS model produced clearer and larger glitches compared to static friction model during low velocity motion. GMS model is capable of characterizing the friction behavior during pre-sliding.

29 November 2012 in Applied Mechanics and Materials
Verified
Journal Article
Closed access
PDF file
LAL. Abdullah
L. Abdullah
Zamberi JamaludinZamberi Jamaludin
Zamberi Jamaludin
TCT.H. Chiew
T.H. Chiew
NRN.A. Rafan
N.A. Rafan
MYM.Y. Yuhazri
M.Y. Yuhazri
Performance analysis in term of identifying the system's transient response, stability and system's dynamical behavior in control system design is undeniably a must process. There are several ways in which a system can be analyzed. An example of well known techniques are using time domain and frequency domain approach. This paper is focused on the fundamental aspect of analysis of classical feedback controller in frequency domain of XY milling table ballscrew drive system. The controller used for the system is the basic PID controller using Matlab SISOTOOL graphical user interface. For this case, the frequency response function (FRF) of the system is used instead of using estimated model of transfer function to represent the real system. Result in simulation shows that after proper tuning of the controller, the system has been successfully being controlled accordingly. In addition, the result also fulfill the set requirement of frequency domain analysis in terms of the required gain and phase margin, the required maximum peak sensitivity and complimentary sensitivity function and the required stability.

1 January 2012 in Procedia Engineering
Verified
Journal Article
Open access
LAL. Abdullah
L. Abdullah
Zamberi JamaludinZamberi Jamaludin
Zamberi Jamaludin
TCT.H. Chiew
T.H. Chiew
NRN.A. Rafan
N.A. Rafan
MMM.S. Syed Mohamed
M.S. Syed Mohamed
System Identification of a system is the very first part in design control procedure of mechatronics system. There are several ways in which a system can be identified. An example of well known techniques are using time domain and frequency domain approach. This paper is focused on the fundamental aspect of system identification of mechatronics system in which it includes the step by step procedure on how to perform system identification. The system for this case is XY milling table ballscrew drive. Both parametric and non-parametric frequency domain approaches were implemented in the procedure. In addition, comparison of estimated model transfer function obtained via non-linear least square (NLLS) and Linear least square estimator algorithm were also being addressed. Result shows that the NLLS technique perform better than LLS technique for this case. The result was judged based on the requirement during model validation procedure such as through heuristic approach (graphical observation) of best fit model with respect to the frequency response function (FRF) of the system.

1 December 2017 in Journal of Mechanical Engineering and Sciences
Verified
Journal Article
Open access
TCT.H. Chiew
T.H. Chiew
Zamberi JamaludinZamberi Jamaludin
Zamberi Jamaludin
AHA.Y. Bani Hashim
A.Y. Bani Hashim
LAL. Abdullah
L. Abdullah
NRN.A. Rafan
N.A. Rafan
MMM. Maharof
M. Maharof
Second order sliding mode control is known for the ability to suppress chattering effect, often being associated with the implementation of a traditional sliding mode controller. The purpose of this paper is to demonstrate and compare the ability of super twisting sliding mode control to suppress chattering as well as to improve tracking performances against the traditional sliding mode controller. Both controllers were designed, numerically analysed and experimentally validated on a second order single-input-singleoutput system direct drive single axis positioning table. A continuous Kalman-Bucy filter was applied to estimate the velocity signal to further improve the overall tracking performance. Results showed that super twisting sliding mode controller was able to successfully suppress chattering effect by smoothening the control input through integration action to form a continuous function, thus dampening the effect of high frequency switching. The effectiveness of this control algorithm would promote its application in real-time application as it provides better control performance as compared to the standard sliding mode controller.