Vicent Ssenteza

Vicent Ssenteza

Auto-generated profile, based on publicly available information

Vicent Ssenteza

Chalmers University of Technology, Kemivägen 10, 412 96 Gothenburg, Sweden

Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
10 November 2023 in Corrosion Science
Verified
Journal Article
Open access
VSVicent Ssenteza
Vicent Ssenteza
JEJohan Eklund
Johan Eklund
SBSedigheh Bigdeli
Sedigheh Bigdeli
TJTorbjörn Jonsson
Torbjörn Jonsson

17 October 2024 in ACS Applied Materials & Interfaces
Verified
Journal Article
Open access
AAAlina Agüero
Alina Agüero
PAPauline Audigié
Pauline Audigié
SRSergio Rodríguez
Sergio Rodríguez
MOMarcos Gutiérrez del Olmo
Marcos Gutiérrez del Olmo
JPJon Pascual
Jon Pascual
LJLars-Gunnar Johansson
Lars-Gunnar Johansson
In this work, a slurry iron aluminide-coated ferritic steel SVM12 was subjected to a laboratory experiment mimicking superheater corrosion in a biomass-fired power boiler. The samples were exposed under model Cl-rich biomass conditions, in a KCl + O2 + H2O environment at 600 °C for 168, 2000, and 8000 h. The morphology of corrosion and the composition of the oxide scale and the coating were investigated by a combination of advanced analytical techniques such as FESEM/EDS, SEM/EBSD, and XRD. Even after short-term exposure, the coating developed a very fast-growing and up to 50 μm thick α-Al2O3 scale in contrast to the spontaneous formation of a protective, thin, dense, slow-growing, and very adhesive α-Al2O3 layer usually formed on metallic materials after high-temperature oxidation. In view of the literature on the formation of oxide scales on alloys and coatings, the formation of an α-Al2O3 scale at this relatively low temperature is very surprising in itself. The thick alumina scale was not protective as its formation resulted in fast degradation of the coating and rapid Fe2Al5 → FeAl phase transformation, which in turn generated porosity inside the coating. In all cases, the resulting thick Al2O3 scale was porous and consisted of both equiaxed α-Al2O3 grains and randomly oriented aggregated alumina whiskers. Potassium is concentrated in the outer part of the Al2O3 scale, while chlorine is concentrated close to the scale/aluminide interface. The unexpected formation of rapidly growing α-Al2O3 at relatively low temperature is attributed to the hydrolysis of aluminum chloride generated in the corrosion process.

5 April 2025 in Materials & Design
Verified
Journal Article
Open access
VSVicent Ssenteza
Vicent Ssenteza
IPItai Panas
Itai Panas
LMLaura Rioja Monllor
Laura Rioja Monllor
ACAnton Chyrkin
Anton Chyrkin
TSTommy Sand
Tommy Sand
TJTorbjörn Jonsson
Torbjörn Jonsson

22 July 2024 in High Temperature Corrosion of Materials
Verified
Journal Article
Open access
PDF file
VSVicent Ssenteza
Vicent Ssenteza
TJTorbjörn Jonsson
Torbjörn Jonsson
JNJohanna Nockert
Johanna Nockert
JLJesper Liske
Jesper Liske
The impact of Cl on alkali-induced high-temperature corrosion of stainless steels/FeCrAl alloys after breakaway oxidation was investigated in a simulated biomass- and waste-fired boiler environment at 600 °C. For this investigation, three alloys were exposed to low Cl load environment (H2O+KCl) and to high Cl load (H2O+KCl+HCl). Post-exposure analysis showed that the stainless steel SVM12 experiences fast oxidation and forms thick double-layered Fe-rich oxide scales. The corrosion attack is further accelerated with addition of HCl for this material with the effect being more pronounced in the inward-growing scale. The FeCrAl and FeCrNi alloys exhibit slower oxidation kinetics after the breakaway corrosion compared to SVM12 in the H2O+KCl exposure. Furthermore, in contrast with SVM12, the addition of HCl did not accelerate the corrosion attack on these alloys. It is argued that the properties of the secondary oxide layer formed after breakaway corrosion are important in the continued corrosion resistance against chlorine-induced corrosion attack. Especially, the Cr content in the inner scales is suggested to be important in corrosion mitigation.

20 July 2023 in Journal of Materials Research and Technology
Verified
Journal Article
Open access
IHImran Hanif
Imran Hanif
VSVicent Ssenteza
Vicent Ssenteza
JEJohan Eklund
Johan Eklund
JOJohanna Nockert Olovsjö
Johanna Nockert Olovsjö
TJTorbjörn Jonsson
Torbjörn Jonsson