3 September 2020 in IEEE Journal of Solid-State Circuits
This article presents a Gm-C-based continuous-time delta-sigma modulator (CTDSM) for artifact-tolerant neural recording interfaces. We propose the feedback-assisted Gm linearization technique, which is applied to the first Gm-C integrator by using a resistive feedback digital-to-analog converter (DAC) in parallel to the degeneration resistor of the input Gm. This enables the input Gm to process the quantization noise, thereby improving the input range and linearity of the Gm-C-based CTDSM, significantly. An energy-efficient second-order loop filter is realized by using a voltage-controlled oscillator (VCO) as the second integrator and a phase quantizer. A proportional-integral (PI) transfer function is employed at the first integrator, which minimizes the output swing while maintaining loop stability. Fabricated in a 110-nm CMOS process, the prototype CTDSM achieves a high input impedance, 300-mVpp linear input range, 80.4-dB signal-to-noise and distortion ratio (SNDR), 81-dB dynamic range (DR), and 76-dB common-mode rejection ratio (CMRR) and consumes only 6.5 μW with a signal bandwidth of 10 kHz. This corresponds to a figure of merit (FoM) of 172.3 dB, which is the state of the art among the neural recording ADCs. This work is also validated through the in vivo experiment.
9 October 2018 in IEEE Journal of Solid-State Circuits
The opamp in the integrators of a continuous-time delta-sigma modulator (CTDSM) has stringent noise and linearity requirements, which lead to large power dissipation. In this paper, a negative-R assisted integrator is proposed to mitigate the opamp's requirements including dc gain, unity gain bandwidth, thermal and 1/f noise, and linearity, thus enabling a drastic power reduction. We present two prototype CTDSMs using the negative-R assisted integrators that employ a single-bit and tri-level feedback digital-to-analog converter (DAC), respectively. The prototype CTDSMs were fabricated in 65-nm CMOS technology. The first CTDSM using a single-bit feedback DAC achieves dynamic range (DR)/signal to noise and distortion ratio (SNDR)/spurious-free dynamic range (SFDR) of 93.1/88.5/100.5 dB in a 20-kHz bandwidth while dissipating only 55 μW from a 1.2-V supply. The second CTDSM, with a tri-level feedback DAC, achieves DR/SNDR/SFDR of 98.2/94.1/107 dB in a 24-kHz bandwidth while dissipating only 68 μW from a 1.2-V supply. The figures of merit of the two CTDSMs are 178.7 and 183.6 dB, respectively, which are the best energy efficiency among state-of-the-art works.
21 November 2019 in IEEE Transactions on Biomedical Circuits and Systems
This paper presents the first CMOS Vascular Endothelial Growth Factor (VEGF) sensor for cancer diagnosis directly from human blood. The sensor incorporates a peptide aptamer-based microneedle that allows the detection of electrochemical reactions with VEGF. This results in a capacitance change between the microneedles and then reads out by a two-step capacitance-to-digital converter (CDC). The proposed two-step CDC consists of a coarse 5b slope ADC and a fine 14b continuous-time delta-sigma modulator (CTDSM). During slow peptide-binding, the slope ADC performs a coarse conversion and the results are used to adjust the current level of the stimulator. After settling of the peptide-binding, based on an adjusted stimulation current, the CTDSM measures the small capacitance changes of the sensor. The prototype chip is fabricated in a 65-nm CMOS process, occupying a 0.87 mm2 active area. The power consumption is 270 W. Thanks to the two-step approach, this work achieves a wide dynamic range of 18.3b, covering a large sensor-to-sensor variation. It also achieves a peak resolution of 13.7b, while maintaining <0.02% errors in 1 to 100 nF baseline capacitance. The overall sensor system successfully detects the VEGF in both phosphate-buffered saline (PBS) and human blood serum. Without the use of precision instruments, this work achieves a resolution of 15 fMrms in range of 0.1 to 1000 pM and denotes the clear VEGF selectivity at 40× in PBS and 5× in the blood serum compared to other proteins (IgG, Con A, and cholera toxin).
9 November 2020 in IEEE Journal of Solid-State Circuits
This article presents a low-power audio continuous-time delta-sigma modulator (CTDSM) that employs a chopped negative-R and a tri-level finite impulse-response (FIR) DAC. The noise of the first opamp is mitigated by using a negative-R at the virtual ground of the first integrator, and the negative-R is then chopped to remove the intrinsic 1/f noise of the negative-R. The highly linear feedback DAC is realized with a 6-tap tri-level FIR-DAC whose inter-symbol interference (ISI) is kept less than -120 dB. The CTDSM fabricated in 65-nm CMOS technology occupies an active area of 0.28 mm². It achieves 99.4-dB SNDR, 101-dB SNR, 102.8-dB dynamic range (DR), and 110.2-dB SFDR in a 24-kHz bandwidth, while consuming only 134 μW. This corresponds to a state-of-the-art figure-of-merit (FoM) of 185.3 dB.
29 December 2023 in IEEE Journal of Solid-State Circuits
This article presents a data-compressive neural recording IC for single-cell resolution high-bandwidth brain–computer interfaces (BCIs). The IC features wired-OR lossy compression during digitization, thus preventing data deluge and massive data movement. By discarding unwanted baseline samples of the neural signals, the output data rate is reduced by 146 $\times $ on average while allowing the reconstruction of spike samples. The recording array consists of pulse-position modulation (PPM)-based active digital pixels (ADPs) with a global single-slope (SS) analog-to-digital conversion scheme, which enables a low-power and compact pixel design with significantly simple routing and low array readout energy. Fabricated in a 28-nm CMOS process, the neural recording IC features 1024 channels (i.e., 32 $\times $ 32 array) with a pixel pitch of 36 $\mu \text{m}$ that can be directly matched to a high-density micro-electrode array (MEA). The pixel achieves 7.4- $\mu \text{V}_{\text {rms}}$ input-referred noise with a −3-dB bandwidth of 300 Hz–5 kHz while consuming only 268 nW from a single 1-V supply. The IC achieves the smallest area per channel (36 $\times $ 36 $\mu \text {m}^{{2}}$ ) and the highest energy efficiency among the state-of-the-art neural recording ICs published to date.
8 September 2023 in IEEE Open Journal of the Solid-State Circuits Society
The energy-efficiency of analog-to-digital converters (ADCs) has improved steadily over the past 40 years, with the best-reported ADC efficiency improving by nearly six orders of magnitude over the same period. The best figure-of-merit (FoM) is achieved with a limited class of ADC in terms of resolution and speed, but the coverage of the best FoM ADC has been expended. Many ADCs with the record FoM open up new applications, and often incorporate multiple combinations of architectural and circuit innovations. It would be very interesting to follow a path of relentless optimization that could be useful to further expand the operating bandwidth of energy-efficient ADCs. To help along this path, this review article discusses the design techniques that focus on optimizing energy efficiency, involving successive-approximation, pipelining, noise-shaping, and continuous-time operation.