31 January 2019 in PLOS ONE
Titanium (Ti) and its alloys possess high biocompatibility and corrosion resistance due to Ti ability to form a passive oxide film, i.e. TiO2, immediately after contact with oxygen. This passive layer is considered stable during function in the oral cavity, however, emerging information associate inflammatory peri-implantitis to vast increases in Ti corrosion products around diseased implants as compared to healthy ones. Thus, it is imperative to identify which factors in the peri-implant micro-environment may reduce Ti corrosion resistance. The aim of this work is to simulate peri-implant inflammatory conditions in vitro to determine which factors affect corrosion susceptibility of Ti-6Al-4V dental implants. The effects of hydrogen peroxide (surrogate for reactive oxygen species, ROS, found during inflammation), albumin (a protein typical of physiological fluids), deaeration (to simulate reduced pO2 conditions during inflammation), in an acidic environment (pH 3), which is typical of inflammation condition, were investigated. Corrosion resistance of Ti-6Al-4V clinically-relevant acid etched surfaces was investigated by electrochemical techniques: Open Circuit Potential; Electrochemical Impedance Spectroscopy; and Anodic Polarization. Electrochemical tests confirmed that most aggressive conditions to the Ti-6Al-4V alloy were those typical of occluded cells, i.e. oxidizing conditions (H2O2), in the presence of protein and deaeration of the physiological medium. Our results provide evidence that titanium’s corrosion resistance can be reduced by intense inflammatory conditions. This observation indicates that the micro-environment to which the implant is exposed during peri-implant inflammation is highly aggressive and may lead to TiO2 passive layer attack. Further investigation of the effect of these aggressive conditions on titanium dissolution is warranted.
24 May 2022 in Anti-Corrosion Methods and Materials
Purpose: The purpose of this paper is to evaluate the protection against corrosion of carbon steel SAE 1020 promoted by a niobium- and titanium-based coating produced from a resin obtained by the Pechini method. Design/methodology/approach: A resin was prepared with ammonium niobium oxalate as niobium precursor and K2TiF6 as titanium precursor. Carbon Steel SAE 1020 plates were dip coated in the resin and calcinated for 1 h at 600 ºC. Scanning electron microscopy, energy dispersive spectroscopy and X-ray diffraction were used to characterize the coating morphologically and structurally. Open circuit potential, electrochemical impedance spectroscopy, anodic potentiodynamic polarization and scanning vibrating electrode technique were used to evaluate the corrosion protection of the coating. Findings: The electrochemical analyses evidence slight protection against corrosion of the coating by itself; however, the needle-like crystal structure obtained may potentially provide a good anchorage site, suggesting the coating could be used as a pretreatment that may present similar application to phosphating processes, generating lower environmental impacts. Originality/value: Due to increasingly restrictive environmental laws, new environmentally friendlier surface treatments must be researched. This paper approaches this matter using a combination of niobium- and titanium-based coating, produced by a cleaner process, the Pechini method.
1 January 2025 in Materials Research
Due to the possible consequences of the greenhouse effect for future generations, solar energy has emerged as a promising alternative due to its great energy potential, especially for Brazil, which is in a privileged geographical position on the planet. The aim of this study is the deposition of Pt/FTO on the counter electrode of dye-sensitized solar cells (DSSC), as there are few studies in the literature on this area, and evaporation deposition is normally used. The counter electrode used was platinum deposited on FTO by chronoamperometry. The tests were performed in triplicate, at 90, 600 and 1800 seconds on AutoLab equipment, model PGSTAT302N. The solar cell was assembled in a sandwich format, with an active area of 0.23 cm2, so we attempted to develop a method for electrodeposition of platinum, using chronoamperometry, obtaining a PCE of 0.517% for deposition in 600 seconds.