30 October 2015 in Applied Optics
Recently, a frequency-diverse, metamaterial-based aperture has been introduced in the context of microwave and millimeter wave imaging. The generic form of the aperture is that of a parallel plate waveguide, in which complementary metamaterial elements patterned into the upper plate couple energy from the waveguide mode to the scene. To reliably predict the imaging performance of such an aperture prior to fabrication and experiments, it is necessary to have an accurate forward model that predicts radiation from the aperture, a model for scattering from an arbitrary target in the scene, and a set of image reconstruction approaches that allow scene estimation from an arbitrary set of measurements. Here, we introduce a forward model in which the metamaterial elements are approximated as polarizable magnetic dipoles, excited by the fields propagating within the waveguide. The dipoles used in the model can have arbitrarily assigned polarizability characteristics. Alternatively, fields measured from actual metamaterial samples can be decomposed into a set of effective dipole radiators, allowing the performance of actual samples to be quantitatively modeled and compared with simulated apertures. To confirm the validity of our model, we simulate measurements and scene reconstructions with a virtual multiaperture imaging system operating in the K-band spectrum (18–26.5 GHz) and compare its performance with an experimental system.
15 March 2016 in IEEE Antennas and Wireless Propagation Letters
A scheme for wireless power transfer (WPT) in the radiative near-field (Fresnel) region is presented. The proposed Fresnel WPT scheme is designed to focus microwaves to a diffraction-limited region where a detector can be positioned, achieving reasonably high power transfer efficiency over moderate distances. The configuration consists of transmit and receive microstrip patch array antennas, with the receiving antenna connected to a power-harvesting half-wave rectifier (rectenna). Fresnel region operation enables the fields radiated by the transmitting aperture to be localized both in range and cross-range. Using Fresnel region focusing, we achieve an increase of 66.8% in the amount of received power when compared to the performance of a conventional beamforming array. We also demonstrate the efficiency improvement by powering an LED using the on-axis and off-axis focusing configurations.
3 January 2017 in Journal of Applied Physics
Wireless power transfer (WPT) has been an active topic of research, with a number of WPT schemes implemented in the near-field (coupling) and far-field (radiation) regimes. Here, we consider a beamed WPT scheme based on a dynamically reconfigurable source aperture transferring power to receiving devices within the Fresnel region. In this context, the dynamic aperture resembles a reconfigurable lens capable of focusing power to a well-defined spot, whose dimension can be related to a point spread function. The necessary amplitude and phase distribution of the field imposed over the aperture can be determined in a holographic sense, by interfering a hypothetical point source located at the receiver location with a plane wave at the aperture location. While conventional technologies, such as phased arrays, can achieve the required control over phase and amplitude, they typically do so at a high cost; alternatively, metasurface apertures can achieve dynamic focusing with potentially lower cost. We present an initial tradeoff analysis of the Fresnel region WPT concept assuming a metasurface aperture, relating the key parameters such as spot size, aperture size, wavelength, and focal distance, as well as reviewing system considerations such as the availability of sources and power transfer efficiency. We find that approximate design formulas derived from the Gaussian optics approximation provide useful estimates of system performance, including transfer efficiency and coverage volume. The accuracy of these formulas is confirmed through numerical studies.
14 April 2016 in IEEE Microwave and Wireless Components Letters
We demonstrate a frequency-diverse aperture for microwave imaging based on a planar cavity at K-band frequencies (18-26.5 GHz). The structure consists of an array of radiating circular irises patterned into the front surface of a double-sided printed circuit board. The irises are distributed in a Fibonacci pattern to maximize spatial diversity at the scene. The printed cavity is a phase-diverse system and encodes imaged scene information onto a set of frequencies that span the K-band. Similar to recently reported metamaterial apertures, the printed cavity imager does not require any mechanically moving parts or complex phase shifting networks. Imaging of a number of targets is shown; these reconstructed images demonstrate the ability of the system to perform imaging at the diffraction limit. The proposed printed cavity imager possesses a relatively large quality factor that can be traded off to achieve higher radiation efficiency. The general mode characteristics of the printed cavity suggest advantages when used in computational imaging scenarios.
1 August 2016 in IET Microwaves, Antennas & Propagation
The authors present a multistatic imaging system at microwave frequencies based on arrays of planar cavity sub‐apertures, or panels. The cavity imager consists of sets of transmit and receive panels, loaded with radiating irises distributed over the sub‐apertures in an aperiodic pattern. This frequency‐diverse aperture produces distinct radiation patterns as a function of frequency that encode scene information onto a set of measurements; images are subsequently reconstructed using computational imaging approaches. Similar to previously reported computational imaging systems, the cavity‐based imager presents a simple system architecture, minimising the number and expense of components required in traditional microwave imaging systems. The cavity imager builds on previous frequency‐diverse approaches, such as the recently reported metamaterial and air‐filled cavity systems, by utilising frequency‐diverse panels for both the transmit and receive sub‐apertures of the imaging system. Though the panel‐to‐panel architecture has greater sensitivity to calibration error, this implementation nevertheless increases mode diversity and, in the context of a computational imaging system, results in improved image reconstructions.
5 February 2018 in IEEE Access
We present the design and experimental demonstration of a cavity-backed, holographic metasurface capable of focusing microwaves in the Fresnel zone. The circular cavity consists of two stacked plates: microwaves are injected into the bottom plate via a coaxial connector, which forms the feed layer, and are coupled to the top holographic metasurface layer via an annular ring on the periphery of the cavity. This coupling results in an inward traveling cylindrical wave in the top layer, which serves as the reference wave for the hologram. A sparse array of slots, patterned into the upper plate, constitutes the hologram that produces the focal spot. To mitigate high sidelobe levels and improve performance a tapered design, facilitated by varying the slot size, is also introduced. The proposed designs—which have a 10 cm diameter, operate at 20 GHz, and form a focal spot at a distance of 10 cm—are validated using full-wave simulations as well as measurements of fabricated samples. The proposed focusing metasurface may find application as a compact source for Fresnel zone wireless power transfer and remote sensing schemes.