Jörg Kaspar

Jörg Kaspar

Auto-generated profile, based on publicly available information

Jörg Kaspar

Fraunhofer Institute for Material and Beam Technology IWS

Research Focus & Metrics

Academic Career Length

27Years (2000-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
22 December 2022 in Journal of Laser Applications
Verified
Journal Article
Open access
PDF file
MMMichael Müller
Michael Müller
CLC. C. Labisch
C. C. Labisch
LGL. Gerdt
L. Gerdt
LBL. Bach
L. Bach
MRM. Riede
M. Riede
CLC. Leyens
C. Leyens
Laser-based direct energy deposition (L-DED) with blown powder enables the simultaneous or sequential processing of different powder materials within one component and, thus, offers the possibility of additive multimaterial manufacturing. Therefore, the process allows a spatially resolved material allocation and fabrication of sharp or even graded material transitions. Within this contribution, the latest results from two major research fields in multimaterial L-DED—(I) automation and (II) rapid alloy development of high entropy alloys (HEAs) by in situ synthesis—shall be presented. First, an automated multimaterial deposition process was developed, which enables the automated manufacturing of three-dimensionally graded specimens. For this, a characterization of the deposition system regarding powder feeding dynamics and resulting powder mixtures in the process zone was conducted. The obtained system characteristics were used to achieve a three-dimensional deposition of specified powder mixtures. The fabricated specimens were analyzed by energy-dispersive x-ray spectroscopy, scanning electron microscopy, and micro hardness measurement. The research demonstrates the increasing readiness of L-DED for the fabrication of multimaterial components. Second, the latest results from rapid alloy development for HEAs by DED are presented. By the simultaneous usage of up to four powder feeders, a vast range of alloy compositions within the Al–Ti–Co–Cr–Fe–Ni HEA system was investigated. For this, tailored measurement systems such as an in-house developed powder sensor were beneficially used. The study shows the influence of a variation of Al on the phase formation and resulting mechanical properties and demonstrates the potential of L-DED for reducing development times for new alloys.

1 August 2023 in Journal of Laser Applications
Verified
Journal Article
Open access
PDF file
MHMaximilian Heidowitzsch
Maximilian Heidowitzsch
LGLeonid Gerdt
Leonid Gerdt
CSConrad Samuel
Conrad Samuel
JMJacob-Florian Maetje
Jacob-Florian Maetje
JKJörg Kaspar
Jörg Kaspar
CLChristoph Leyens
Christoph Leyens
The epitaxial growth of coarse and columnar grain structures along the build direction of additive manufactured metals is a usual phenomenon. As a result, as-built components often exhibit pronounced anisotropic mechanical properties, reduced ductility, and, hence, a high cracking susceptibility. To enhance the mechanical properties and processability of additive manufactured parts, the formation of equiaxed and fine grained structures is thought to be most beneficial. In this study, the potential of grain refinement by ultrasonic excitation of the melt pool during laser wire additive manufacturing has been investigated. An ultrasound system was developed and integrated in a laser wire deposition machine. AISI 316L steel was used as a substrate and feedstock material. A conversion of coarse, columnar grains (dm = 284.5 μm) into fine, equiaxed grains (dm = 130.4 μm) and a weakening of typical -fiber texture with increasing amplitude were verified by means of light microscopy, scanning electron microscopy, and electron backscatter diffraction analysis. It was demonstrated that the degree of grain refinement could be controlled by the regulation of ultrasound amplitude. No significant changes in the dendritic structure have been observed. The combination of sonotrode/melt pool direct coupling and the laser wire deposition process represents a pioneering approach and promising strategy to investigate the influence of ultrasound on grain refinement and microstructural tailoring.

1 September 2023 in High Entropy Alloys & Materials
Verified
Journal Article
Open access
PDF file
JKJ. Kaspar
J. Kaspar
AHA. Hilhorst
A. Hilhorst
LGL. Gerdt
L. Gerdt
MMM. Müller
M. Müller
MHM. Heidowitzsch
M. Heidowitzsch
CLC. Leyens
C. Leyens
In this work, we propose a strategy for high-throughput design and development of compositionally complex alloys combining theoretical and experimental alloy screening. This methodology was applied for the exploration of the (Co2CrFeNi2)1-x-yTixAly subsystem of so-called high entropy superalloys in the Al–Co–Cr–Fe–Ni–Ti alloy system. Alloy design was guided by thermodynamic calculations based on the CALPHAD approach. The evolution of the microstructure with increasing Al and Ti content was analyzed in the as-built, homogenized and age-hardened conditions by means of scanning electron microscopy, energy-dispersive X-ray spectroscopy and electron backscattered diffraction. Additionally, the evolution of the sample hardness with increasing Al and Ti contents was determined for all conditions. Based on the experimental results, the reliability of the CALPHAD calculations was assessed. Generally, a good agreement between calculations and experiments is achieved in the homogenized state. In the aged conditions, the CALPHAD predictions of the precipitation processes are partly inaccurate and need improvement. Optimal Al and Ti concentrations are derived for age hardening through L12 and combined L12 + B2 precipitations.

14 September 2022 in Materials
Verified
Journal Article
Open access
PDF file
AZAndré T. Zeuner
André T. Zeuner
LGLeonid Gerdt
Leonid Gerdt
AOAndrea Ostwald
Andrea Ostwald
PGPeter Grün
Peter Grün
MBMaria Barbosa
Maria Barbosa
Martina ZimmermannMartina Zimmermann
Martina Zimmermann
There are only a few cost-effective solutions for coating applications in combined mechanical loading and corrosive environments. Stainless steel AISI 304 has the potential to fill this niche, showing excellent corrosion resistance while utilizing the deformation-induced phase transformation from γ-austenite to α’-martensite, which results in an increase in strength. However, it is not known whether this can occur in laser cladded material. Therefore, laser cladded AISI 304 coatings in as-cladded condition and after heat treatment at 1100 °C for 60 min were investigated before and after bending deformation, by means of light microscopy, energy-dispersive X-ray spectroscopy and electron backscatter diffraction. It was shown that due to the dendritic microstructure accompanied by an inhomogeneous distribution of the main alloying elements (Cr and Ni), no deformation-induced phase transformation occurred in the as-cladded coating. The applied approach with subsequent solution heat treatment at 1100 °C for 60 min resulted in a homogeneous γ-austenite microstructure, so that a deformation-induced martensitic transformation (DIMT) could occur in the coatings. However, the volume fraction of martensite that had been formed locally at individual shear bands was rather low, which can be possibly attributed to the high Ni content of the feedstock, stabilizing the γ-austenite microstructure. This study shows the possibility of exploiting the DIMT mechanism in heat-treated laser-cladded AISI 304 coatings.

14 July 2024 in Materials Science and Engineering: A
Verified
Journal Article
Closed access
RKRobert Kühne
Robert Kühne
FBFlorian Bittner
Florian Bittner
TTThomas Töppel
Thomas Töppel
ARAlexander Raßloff
Alexander Raßloff
AZAndré Till Zeuner
André Till Zeuner
MKMarkus Kästner
Markus Kästner

1 April 2000 in Practical Metallography
Verified
Journal Article
Closed access
JKJörg Kaspar
Jörg Kaspar
ALArnhold Luft
Arnhold Luft
Article Untersuchung der Mikrostruktur kubisch-raumzentrierter Metalle nach Laserschockbehandlung / An Investigation of the Microstructure of Body Centred Cubic Metals after Laser Shock Treatment was published on April 1, 2000 in the journal Practical Metallography (volume 37, issue 4).