25 January 2019 in IEEE Transactions on Instrumentation and Measurement
1 May 2018 in IEEE Journal on Emerging and Selected Topics in Circuits and Systems
Emerging millimeter-wave (mmW) wireless systems require beamforming and multiple-input multiple-output (MIMO) approaches in order to mitigate path loss, obstructions, and attenuation of the communication channel. Sharp mmW beams are essential for this purpose and must support baseband bandwidths of at least 1 GHz to facilitate higher system capacity. This paper explores a baseband multi-beamforming method based on the spatial Fourier transform. Approximate computing techniques are used to propose a low-complexity fast algorithm with sparse factorizations that neatly map to integer W/L ratios in CMOS current mirrors. The resulting approximate fast Fourier transform (FFT) can thus be efficiently realized using CMOS analog integrated circuits to generate multiple, parallel mmW beams in both transmit and receive modes. The paper proposes both 8and 16-point approximate-FFT algorithms together with circuit theory and design information for 65-nm CMOS implementations. Post-layout simulations of the 8-point circuit in Cadence Spectre provide well-defined mmW beam shapes, a baseband bandwidth of 2.7 GHz, a power consumption of 70 mW, and a dynamic range >42.2 dB. Preliminary experimental results confirm the basic functionality of the 8-beam circuit. Schematic-level analysis of the 16-beam I/Q version show worst-case and average side lobe levels of -10.2 dB and -12.2 dB at 1 GHz bandwidth, and -9.1 dB and -11.3 dB at 1.5 GHz bandwidth. The proposed multibeam architectures have the potential to reduce circuit area and power requirements while meeting the bandwidth requirements of emerging 5G baseband systems.
14 January 2021 in IEEE Access
With the proliferation of Internet-of-Things (IoT) devices at public facilities, work places, homes, and beyond, securing data communications is becoming increasingly challenging. This paper describes the analysis and practical implementation of synchronized hyperchaotic maps for securing short-range data links in IoT devices. The data is stream-encrypted in the physical layer using chaotic masking and decrypted using a synchronized chaotic map. Two different energy-efficient chaotic encryption schemes are proposed: 1) direct sampling and masking of analog sensor outputs, thus avoiding the need for analog-to-digital (ADC) conversion; and 2) bit scrambling and masking of digital data. Both schemes were initially investigated and simulated in MATLAB. The effective number of encryption keys when using such hyperchaotic maps was also studied. Simulation results were validated by implementing two maps on circuit boards using high-speed discrete components. Experimental results for digital communication show a bit error rate (BER) of ≈ 2 × 10-6 at a bit rate of 10 kbps and a clock frequency of 0.5 MHz, making the approach feasible for high-fidelity real-time speech and image transmission without additional error control coding. An energy-efficient on-chip chaotic encryption system was developed using analog current-mode circuits and has a simulated power consumption of <100 μW in the TSMC 180 nm CMOS process, which is sufficiently low for use in many battery-less miniaturized IoT sensor nodes.
9 February 2022 in IEEE Access
The paper describes highly-sensitive passive electric potential sensors (EPS) for non-contact detection of multiple biophysical signals, including electrocardiogram (ECG), respiration cycle (RC), and electroencephalogram (EEG). The proposed EPS uses an optimized transimpedance amplifier (TIA), a single guarded sensing electrode, and an adaptive cancellation loop (ACL) to maximize sensitivity (DC transimpedance $= 150\,\,\text{G}\Omega $ ) in the presence of power line interference (PLI) and motion artifacts. Tests were performed on healthy adult volunteers in noisy and unshielded indoor environments. Useful sensing ranges for ECG, RC, and EEG measurements, as validated against reference contact sensors, were observed to be approximately 50 cm, 100 cm, and 5 cm, respectively. ECG and RC signals were also successfully measured through wooden tables for subjects in sleep-like postures. The EPS were integrated with a wireless microcontroller to realize wireless sensor nodes capable of streaming acquired data to a remote base station in real-time.
13 October 2022 in IEEE Access
This paper describes a highly-integrated CMOS system-on-chip (SoC) for active structural health monitoring (SHM). The chip integrates ultrasonic power and bidirectional half-duplex data transfer, a power management unit (PMU), and an ultrasound transceiver to enable wireless ultrasonically-coupled sensor SHM networks on structures. The PMU includes an active bias-flip rectifier with off-delay compensation, a high-efficiency dual-path DC-DC converter with inductor time-sharing, and five switched-capacitor DC-DC converters to generate multi-level spectrally band-limited pulses for guided-wave SHM. The chip was fabricated in a standard 180 nm process and has a die area of $2\times 2$ mm2. Test results show power conversion efficiency (PCE) > 85% for the active rectifier, > 70% for the inductive DC-DC converter, and > 60% for the switched-capacitor DC-DC converters. Output pulses have a peak-to-sidelobe ratio (PSL) > 30 dB and worst-case out-of-band emissions < −30 dB, respectively. The SoC was integrated with a low-power microcontroller and passive components to realize miniaturized (15 mm $\times 30$ mm) wireless SHM nodes. A set of nodes was deployed on an SHM test-bed (carbon fiber reinforced polymer sheet) representing an airframe panel. Tests on this wireless network confirm both long-range ultrasound power/data transfer and the ability to detect structural damage.