12 May 2017 in IEEE Transactions on Magnetics
This paper presents a new switched reluctance motor (SRM) with wide speed range for the application of electric vehicles (EVs). It has an in-wheel structure for direct drive and multiple teeth per stator pole to enhance output torque. Also, the number of rotor poles is more than that of stator teeth. A 6/16 three phase in-wheel SRM with the concepts of multi-teeth per stator pole and more rotor poles than stator teeth has been proposed for analysis. The torque performance of the topology with multi-teeth per stator pole is proved by theoretical analysis. Moreover, a new design formula is introduced for a novel combination of stator and rotor poles. The parameters of the motor are optimized by genetic algorithm (GA) method for the maximum torque output. Then the torque performance is computed by finite element method (FEM) and compared with its counterparts, including three phase 6/8 and 6/10 SRMs. The FEM results exhibit higher torque density for the proposed topology.
16 October 2018 in IEEE Transactions on Energy Conversion
In this paper, a new 6/10 hybrid switched reluctance motor (HSRM) is proposed. This original topology deploys permanent magnets (PMs) between adjacent stator poles of a divided teeth SRM. The function of the PMs is to weaken the magnetic saturation in stator poles, which is a major obstacle of torque improvement for divided teeth SRMs. Besides, the magnetic flux in the airgap increases as well. Hence, the output torque can be increased significantly. The flux distribution of the topology is analyzed by using equivalent magnetic circuit (EMC). The topology is optimized by using genetic algorithm (GA) for the best torque performance. Additionally, the characteristics of the proposed topology are compared with a 12/8 SRM, a 6/10 two-teeth SRM, a 12-slot, 8-pole three-phase six-state PM brushless DC motor (BLDCM) and a flux switching permanent magnet motor (FSPM) of the same dimension. A prototype of the proposed topology is manufactured for experimental verification. The simulation and experimental results indicate that the proposed topology can achieve high torque density and high PM utilization factor simultaneously.
1 December 2022 in IEEE Transactions on Power Electronics
To suppress the torque ripple for smooth speed control of electric drives, active disturbance rejection (ADR) controller based on generalized integrator (GI) extended state observer (ESO) (GIESO) is developed in this article. Deadbeat ADR controller is employed to control the current, allowing the current control algorithm to be simplified. An adaptive GIESO is developed to address the instability problem caused by the two-step delay in the current control loop. Based on the system stability analysis, the design guideline for the adaptive resonant gain is determined. The proposed adaptive GIESO allows the system to be stable across the entire speed range while suppressing speed ripple to within 1 r/min.
15 December 2021 in IEEE Transactions on Industrial Electronics
Permanent magnet Vernier motors (PMVMs) possess the advantage of high torque density for high-performance applications. However, the low power factor challenge makes it unacceptable for direct-drive applications. A lack of accurate modeling method based on the motor sizing law, i.e., air-gap flux density, linear current density, and motor geometry parameters, raises difficulties for machine designers to further conduct research on the performance metrics. This article presents a deep investigation into the analytical modeling technique for surface PMVMs (SPMVMs). It can identify an accurate approach to obtain the performance metrics, including electromagnetic torque and power factor. The modeling technique is developed based on the conformal mapping method. By using this, both radial and tangential permeability functions can be calculated to obtain the motor magnetic loading accurately, considering the leakage flux. The slotting effect on both air-gap flux density and armature-winding function is analyzed to achieve a precise formula for torque and power factor computations. The new modeling technique is applied to integral-slot SPMVMs with different slot/pole combinations, gear ratios, slot openings, and magnet thickness to evaluate the impacts of motor parameters on high-power-factor and high-torque-density designs. Finally, an SPMVM with the characteristics of high torque density and power factor is fabricated to verify the analytical model at the power rating of 0.8 kW and the speed of 500 r/min. The experimental results show that the prototype exhibits a high power factor of 0.9 and high torque density 22.5 Nm/L.
6 January 2022 in IEEE Transactions on Industrial Electronics
This article designs parameter adaptation algorithms for online simultaneous identification of a two-parameter sigmoid inverter model for compensating inverter nonlinearity to reduce the voltage error in flux estimation for a position sensorless motor drive. The inverter model has two parameters, $a_2$ and $a_3$ , where $a_2$ is “plateau voltage” and $a_3$ is a shape parameter that mainly accounts for the stray capacitor effect. Parameter $a_3$ is identified by the $(6k\pm 1)$ th order harmonics in measured current. Parameter $a_2$ is identified by the amplitude mismatch of the estimated active flux. It is found that the classic linear flux estimator, i.e., the hybrid of voltage model and current model, cannot be used for $a_2$ identification. This article proposes to use a saturation function based nonlinear flux estimator to build an effective indicator for $a_2$ error. The coupled identifiability of the two parameters is revealed and analyzed, which was not seen in literature. The concept of the low current region where the two-way coupling between $a_2$ and $a_3$ occurs is established. In theory, it is suggested to stop the inverter identification in the low current region. However, the experimental results in which dc bus voltage variation and load change are imposed have shown the effectiveness of the proposed online inverter identification and compensation method, even in low current region.
6 December 2022 in IEEE Transactions on Industrial Electronics
This article investigates a high power-factor permanent magnet vernier machine (PMVM) equipped with low-coupling hybrid concentrated-winding (CW). The proposed hybrid-CW, carrying both star- and delta-winding sets, exhibits a good filtering property to both sub- and super-order harmonics. Through the meticulous design of the short coil pitch, the ratio of inductance to magnet flux linkage is decreased, leading to a great improvement in power factor. The proposed low-coupling winding design contributes to further power factor improvement by reducing the inductance while retaining the magnet flux linkage. It is revealed that the mutual coupling between different coils of a single phase and that between different windings of three phases is suppressed significantly in the hybrid-CW, thus leading to a high power factor and potentially high fault tolerance. Finite element results show that the proposed hybrid-CW PMVM exhibits a significantly improved power factor up to 0.96 from 0.83 and 0.75, as compared with two counterpart PMVMs with open-slot and split-tooth structures, respectively. Benefiting from the magnetic gearing effect, the proposed PMVM has a promising active torque density of 40 N⋅m/L. Taking the end-winding volume into consideration, the proposed PMVM exhibits an actual torque density of 21.98 N⋅m/L, which is 22.52% and 52.43% higher than the investigated open-slot and split-tooth counterpart PMVMs. Finally, a prototype is fabricated and tested to validate the high-power-factor and high-torque-density features of the proposed hybrid-CW PMVM.