Haoze Wang

Haoze Wang

Auto-generated profile, based on publicly available information

Haoze Wang

School of Aeronautics and Astronautics, Sun Yat-sen University, Shenzhen, China

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
11 February 2022 in IEEE/ASME Transactions on Mechatronics
Verified
Journal Article
Closed access
HWHaoze Wang
Haoze Wang
ZWZhigang Wu
Zhigang Wu
KLKun Liu
Kun Liu
JWJingbo Wei
Jingbo Wei
HHHongJin Hu
HongJin Hu
This article presents modeling and control strategies of a novel axial hybrid magnetic bearing (AHMB) for household flywheel energy storage system (FESS). The AHMB combines a passive permanent magnet (PM) magnetic bearing (MB) and an axial active MB in one unit, thus can offer benefits such as compactness of the structure, high load capacity, and low power consumption. A coupled magnetic field-circuit method is proposed for modeling this bearing. Compared with the regular equivalent magnetic-circuit (EMC) method, it introduces special concerns of the complex air-gap field, calculated from the conformal transformation of the air-gap geometry, to take into account the effect of flux fringing and leakage. A low-cost Hall sensor is used to replace the expensive Eddy-current position sensor to measure the changes in air gap flux density caused by the rotor axial displacement. Therefore, a novel flux density feedback control is adopted instead of the traditional position feedback control to directly stabilize the magnetically suspended flywheel. A prototype of this bearing is designed and fabricated, which is tested in a small-scale FESS. The simulation results and the experimental results demonstrate that the proposed model provides better accuracy than the traditional EMC and the flux-density feedback control strategy based on a low-cost Hall sensor can achieve a consistent performance with the traditional position feedback control strategy.

28 September 2022 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
HHHong-Jin Hu Hu
Hong-Jin Hu Hu
KLKun Liu
Kun Liu
HWHaoze Wang
Haoze Wang
JWJingbo Wei
Jingbo Wei
A switching power amplifier (SPA) provides the driving current for an active magnetic bearing (AMB) to achieve magnetic suspension (MS) control. The performances of the current bandwidth and current ripple should be significantly considered in the SPA of the AMB. The SPA can obtain a wide bandwidth by increasing the dc-link voltage. However, a high dc-link voltage will cause a high current ripple. To achieve a wide bandwidth and low current ripple, a new GaN-device-based SPA for the AMB of a flywheel energy storage system (FESS) is proposed in this article. The GaN SPA can operate at a high switching frequency and high dc-link voltage. Thus, the GaN SPA can improve the performance of the current bandwidth and current ripple compared to the conventional SPA. According to the characteristics of the GaN SPA, a low-loss PWM method and an optimal dead time strategy is proposed to increase the efficiency of the SPA. Furthermore, a high-response control approach of dead-beat model predictive control is proposed to further improve the current bandwidth. The proposed GaN SPA is applied in a 500-kW MS FESS prototype. The effectiveness of the SPA is verified experimentally.

20 August 2021 in IEEE Transactions on Magnetics
Verified
Journal Article
Closed access
HWHaoze Wang
Haoze Wang
KLKun Liu
Kun Liu
JWJingbo Wei
Jingbo Wei
HHHongjing Hu
Hongjing Hu
In this article, an analytical method is presented for modeling the complex air gap field distribution and the magnetic force of a novel permanent magnet (PM) bias hybrid magnetic thrust bearing (HMTB). This bearing has a very compact structure and is proposed to replace the traditional magnetic thrust bearings (MTBs) for high-speed rotor systems. The proposed method introduces the notion of the complicated air gap field, calculated from the Schwarz–Christoffel transformation of the air gap geometry, to take into account the effect of slot fringing and leakage. As a result, accurate solutions of the flux distribution and the bearing force can be obtained, which shows good agreement with the results of the finite-element method (FEM). The prototype of the HMTB is designed, analyzed, and tested. The results of the analytical model are compared with experimental data.

19 September 2022 in Energy Reports
Verified
Journal Article
Open access
HHHongjin Hu
Hongjin Hu
KLKun Liu
Kun Liu
JWJingbo Wei
Jingbo Wei
HWHaoze Wang
Haoze Wang

1 June 2022 in Energies
Verified
Journal Article
Open access
PDF file
HHHongjin Hu
Hongjin Hu
HWHaoze Wang
Haoze Wang
KLKun Liu
Kun Liu
JWJingbo Wei
Jingbo Wei
XSXiangjie Shen
Xiangjie Shen
A space vector pulse width modulation (SVPWM) algorithm is an important part of the permanent magnet synchronous machine (PMSM) drive to achieve direct current (DC) to alternating current (AC) conversion. The execution of the conventional SVPWM algorithm is a complex process which will limit the sampling frequency of the high-speed PMSM drive. Low sampling frequency will cause high current total harmonic distortion (THD) and eddy current loss. To increase the sampling frequency, this paper proposes a novel simplified SVPWM algorithm. The proposed SVPWM algorithm turns the vector composition problem of the conventional SVPWM algorithm into an optimization problem of the dwell time of the basic vector. The proposed SVPWM algorithm has an optimal vector dwell time (OVDT). The dwell time of the basic vector can be directly calculated by solving the optimization problem. The proposed SVPWM algorithm does not need sector identification compared to the conventional algorithm. The experiments of the proposed SVPWM algorithm are performed in a high-speed PMSM drive of a flywheel energy storage system (FESS). Compared to the conventional SVPWM algorithm, the execution time of the proposed SVPWM algorithm is reduced by 38%. By using the proposed SVPWM algorithm, the sampling frequency can be increased from 33 kHz to 40 kHz. With the higher sampling frequency, the current THD is reduced by 25.6%. The effectiveness of the proposed simplified SVPWM algorithm is verified experimentally.

10 November 2020 in IEEE Transactions on Plasma Science
Verified
Journal Article
Closed access
HWHaoze Wang
Haoze Wang
ZWZhigang Wu
Zhigang Wu
KLKun Liu
Kun Liu
JWJingbo Wei
Jingbo Wei
Compulsator provides an excellent approach to achieve compact energy storage and pulsed power generation for several multi-MJ, multi-GW applications, including electromagnetic launchers, directed energy systems, and fusion reactors. There is a continuous research effort toward increasing the power capability and compactness of this machine since its invention. In general, specific machine designs aim to maximize the output current and power by minimizing the transient inductance of the armature winding. The field and the inductance of the armature winding are some of the most important parameters in the compulsator design. This article presents the development of a generic method to analyze the magnetic fields and inductances of the armature windings in compulsators based on fundamental principles. It derives analytical models for inductance calculation in various types of alternators as unified terms of simplified formulas. These are used for the design, analysis, and optimization of all air-core, iron-core, compensated, and uncompensated pulsed alternators (PAs). By comparing the distribution of armature reaction fields and the self-inductances in compulsators having different configurations, this article investigates the basic relationships between the topology of the alternator and the fields and inductances. This is not limited only to the study of PAs but it can also be used in both slotless and air-core conventional machines.